Bellini CGH6401 Installation And Operating Instructions Manual
60/90cm gas hob
Hide thumbs
Also See for CGH6401:
- Installation and operating instructions manual (13 pages) ,
- Installation & operation instructions (31 pages)
Subscribe to Our Youtube Channel
Related Manuals for Bellini CGH6401
Summary of Contents for Bellini CGH6401
- Page 1 20120323 issue 2 For warranty service call 1300 373 199(Australia) or 0508 123108(New Zealand) to connect you to the nearest authorised service centre CGH6401 CGH6401-F CGH9501 CGH9501-F BG604X BG604X-F BG905X BG905X-F...
-
Page 2: Table Of Contents
Bellini – 60/90cm gas hob Installation and Operating Instructions Contents Page INTRODUCTION AND SAFETY WARNINGS OPERATING INSTRUCTIONS CLEANING INSTRUCTIONS TROUBLESHOOTING INSTALLATION WARRANTY SERVICING and PARTS WARRANTY... -
Page 3: Introduction And Safety Warnings
These instructions apply only to the models CGH9501 and BG905X – 5 burner models and the CGH6401 and BG604X – 4 burner models, for use with Natural Gas or Universal LPG. NOTE: Refer to gas type label and data plate label to ensure appliance is setup for the correct gas type. -
Page 4: Operating Instructions
DOT. BURNER AND UTENSIL CHOICE Depending on the hotplate model, the burner choices are: Model CGH6401: Auxiliary (small), Semi-Rapid (medium), and Rapid (large) burners. Models CGH9501 and BG905X: Auxiliary (small), Semi-Rapid (medium), Rapid (large), and Triple ring (wok) burners. -
Page 5: Cleaning Instructions
Bellini – 60/90cm gas hob 3. CLEANING INSTRUCTIONS GENERAL Cleaning and maintenance should be carried out with the appliance cold especially when cleaning the enameled parts. Avoid leaving alkaline or acid substances(lemon juice, vinegar etc.) on the surfaces. STAINLESS STEEL The stainless steel hob of the hotplate must be cleaned regularly (e.g. -
Page 6: Troubleshooting
Bellini – 60/90cm gas hob 4. TROUBLESHOOTING Servicing of the hotplates must only be done by an authorised service representative (see back of this booklet) and the hotplate must not be modified. Power must be disconnected before any servicing or maintenance is conducted. -
Page 7: Installation
GAS and ELECTRICAL CONNECTION LOCATIONS and OVERALL DIMENSIONS: Model CGH6401: Bench cutout size, 555 mm wide x 473 mm deep. Bench top thickness, 30 – 40 mm (3 – 4 cm). Rev: 8-9-2010... - Page 8 Bellini – 60/90cm gas hob Model CGH9501: Bench cutout size, 830 mm wide x 473 mm deep. Bench top thickness, 30 – 40 mm (3 – 4 cm). Model BG604X: Bench cutout size, 555 mm wide x 473 mm deep.
- Page 9 Bellini – 60/90cm gas hob Model BG905X: Bench cutout size, 830 mm wide x 472 mm deep. Bench top thickness, 30 – 40 mm (3 – 4 cm). Once satisfied that minimum clearances to combustible can be achieved, cut out the bench top to the dimensions specified.
- Page 10 Fit a manometer with a 6 mm rubber hose to the test point on the regulator (for natural gas). For the Model CGH6401, light one Rapid and Auxiliary burner and adjust test point pressure to 1.00 kPa. Turn the two burners off and on again and recheck the pressure is same as set previously or adjust as required.
- Page 11 Bellini – 60/90cm gas hob For the Models CGH9501, BG604X and BG905X, light the Triple Ring and Auxiliary burner and adjust test point pressure to 1.00 kPa. Turn the two burners off and on again and recheck the pressure is same as set previously or adjust as required.
-
Page 12: Warranty Servicing And Parts
Consumer until the expiry of two (2) years (Warranty Period). If within the Warranty Period a manufacturing defect is discovered in the Bellini product or it fails to perform to the Company’s specifications as a result of some defect in materials, components or workmanship (Defect) then the Company will, at its option, repair the Bellini product or supply a replacement Bellini product free of charge. - Page 13 1.10 If you are required to transport the Bellini product to the Company or its service agent, you must ensure it is safely disconnected by a qualified tradesman and securely packed and insured. The Company does not accept any responsibility for loss or damage of the Bellini product prior to it being received by the Company or its service agent.
Need help?
Do you have a question about the CGH6401 and is the answer not in the manual?
Questions and answers