Advertisement
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Bellini CGH9501
Summary of Contents for Bellini CGH9501
-
Page 2: Table Of Contents
Bellini – 60/90cm gas hob Installation and Operating Instructions Contents Page INTRODUCTION AND SAFETY WARNINGS OPERATING INSTRUCTIONS CLEANING INSTRUCTIONS TROUBLESHOOTING INSTALLATION SERVICING and PARTS WARRANTY... -
Page 3: Introduction And Safety Warnings
Please carefully read the following installation and operating instructions to ensure you get the safest operation from this appliance. These instructions apply only to the models CGH9501 and BG905X – 5 burner models and the CGH6401 and BG604X – 4 burner models, for use with Natural Gas or Universal LPG. -
Page 4: Operating Instructions
Depending on the hotplate model, the burner choices are: Model CGH6401: Auxiliary (small), Semi-Rapid (medium), and Rapid (large) burners. Models CGH9501 and BG905X: Auxiliary (small), Semi-Rapid (medium), Rapid (large), and Triple ring (wok) burners. Model BG604X: Auxiliary (small), Semi-Rapid (medium), and Triple ring (wok) burners. -
Page 5: Cleaning Instructions
Bellini – 60/90cm gas hob 3. CLEANING INSTRUCTIONS GENERAL Cleaning and maintenance should be carried out with the appliance cold especially when cleaning the enameled parts. Avoid leaving alkaline or acid substances(lemon juice, vinegar etc.) on the surfaces. STAINLESS STEEL The stainless steel hob of the hotplate must be cleaned regularly (e.g. -
Page 6: Troubleshooting
Bellini – 60/90cm gas hob 4. TROUBLESHOOTING Servicing of the hotplates must only be done by an authorised service representative (see back of this booklet) and the hotplate must not be modified. Power must be disconnected before any servicing or maintenance is conducted. -
Page 7: Installation
Bellini – 60/90cm gas hob 5. INSTALLATION IMPORTANT NOTE: Refer to the Warnings in Section 1 of these Instructions. This hotplate must be installed in accordance with: • AS 5601 - Gas Installations (for Australia) • NZS 5261 – Code of Practice for the Installation of Gas Burning Appliances and Equipment (for New Zealand) •... - Page 8 Bellini – 60/90cm gas hob Model CGH9501: Bench cutout size, 830 mm wide x 473 mm deep. Bench top thickness, 30 – 40 mm (3 – 4 cm). Model BG604X: Bench cutout size, 555 mm wide x 473 mm deep.
- Page 9 Bellini – 60/90cm gas hob Model BG905X: Bench cutout size, 830 mm wide x 472 mm deep. Bench top thickness, 30 – 40 mm (3 – 4 cm). Once satisfied that minimum clearances to combustible can be achieved, cut out the bench top to the dimensions specified.
- Page 10 Bellini – 60/90cm gas hob Then a particle board or similar heat baffle must be installed under the hob to prevent accidental touching of the underside surface. Leave sufficient rear clearance access gas and electrical connections. ELECTRICAL CONNECTION: Install a 10 amp general purpose...
- Page 11 Bellini – 60/90cm gas hob For the Models CGH9501, BG604X and BG905X, light the Triple Ring and Auxiliary burner and adjust test point pressure to 1.00 kPa. Turn the two burners off and on again and recheck the pressure is same as set previously or adjust as required.
-
Page 12: Servicing And Parts
Trade Practices Act and similar State and Territory Laws. The original purchaser of this Bellini product is provided with the following warranty, subject to the following warranty conditions. - Page 13 Whilst every effort is made to ensure that descriptions, specifications and other information in this publication is correct, no warranty is given in respect thereof and the company shall not be liable for any errors therein. NOTES: Cat. No. CGH6401, CGH9501, BG604X, BG905X. Rev: 8-9-2010...
Need help?
Do you have a question about the CGH9501 and is the answer not in the manual?
Questions and answers