Installing Feet; Checking/Adding Oil; Operation - Ryobi RA-C2550 Operator's Manual

key. Make sure the handle is securely fixed.

InstALLIng feet

See figure 4.
1. Place a rubber foot under the left supporting frame at
the front. Align the screw holes.
2. Insert a screw and washer in the holes in the rubber
foot and the supporting frame from the bottom.
3. Insert a washer at the other end.
4. Secure the rubber foot with a hex nut.
5. Repeat the above steps to install the other foot on the
right.
6. Ensure the compressor is stable by lightly applying
lateral force on it.
InstALLIng wHeeLs
See figure 5.
1. Insert an axle bolt and washer in the centre hole of
the wheel.
2. Insert the threaded part of the axle bolt in the hole
in the rear supporting frame on the left side. Insert a
washer on both sides of the frame.
3. Secure the axle bolt with a hex nut.
4. Attach the wheel axle cover to the centre of the wheel.
5. Repeat the above steps to install the other wheel on
the right.
6. Ensure the compressor is stable by lightly applying
lateral force on it.
InstALLIng AIR fILteR
See figure 6.
Attach the air filter to the motor cover. Screw in a clockwise
direction to fasten securely.

cHeckIng/AddIng oIL

See figure 7.
To avoid damage to the compressor, add oil before
starting and check oil level before each use.
Always check the oil when the unit is sitting on a level
surface and before first use.
1. There is a red dot in the center of the sight glass.
2. An oil level at the top of the red dot indicates oil is at
maximum level.
3. An oil level at or below the bottom of the red dot
indicates oil is below desired level, and oil should be
added.
to add oil:
1. Unscrew the cap of oil fill hole.
2. Using a funnel, carefully pour oil into the oil fill hole. Fill
only with synthetic oil SAE-30.
note: Avoid using too much oil. Ensure that the level
wARnIng
of the oil does not exceed the top of the red dot at
sight glass.
3. Tighten the cap securely into the oil fill hole.
Replace the oil after the first 10 hours of operation and
every 100 hours following the first oil change. Refer to the
Replacing oil section for details.

oPeRAtIon

Do not disassemble check valve, tank drain valves or
safety relief valve with air in tank — bleed tank.
Always wear eye protection with side shields. Failure
to do so could result in objects being thrown into your
eyes resulting in possible serious injury.
Do not attach any tools to the open end of the hose until
start-up has been completed.
Do not use in an environment that is dusty or otherwise
contaminated. Using the air compressor in this type of
environment may cause damage to the unit.
tRAnsPoRtIng tHe AIR comPRessoR
See figure 8a.
The air compressor should be moved as instructed.
This will help you to avoid damaging the wheel or the air
compressor by rolling it over items in its path.
Ensure the air compressor is unplugged, make sure the
power cord is secured in the cord wrap.
to move the air compressor:
1. Grasp the front handle firmly with two hands.
2. Lift the air compressor toward you. Make sure the
compressor is balanced on the wheels.
3. Push the unit along to the desired location.
4. Lower the air compressor until it sits securely on a flat
surface.
to transport the air compressor up or down stairs:
See figure 8b.
1. Grasp the front handle and rear handle firmly. Lift the
unit into a safe and comfortable carrying position.
note: Use good lifting techniques and get help if needed.
2. With proper footing and balance, carry the unit one
4
dAngeR
wARnIng
wARnIng
cAUtIon