Operating In All Metal Mode; Ground Grab; (Gg) Computerized Ground Balancing; Setting The Controls - Teknetics G2 Owner's Manual

OPERATING IN ALL METAL MODE

The All Metal Mode is more sensitive than the Discrimination Mode, and is used to
find all types of metal objects in the ground. The searchcoil must be in motion for
objects to be detected.
®

Ground Grab

(GG) Computerized Ground Balancing

Naturally occurring minerals in soil look like metal to a metal detector, so you want to
cancel out this mineral signal coming from the ground, and only detect the signal from
metal objects in the ground.
So before using your detector, set it in All Metal Mode and perform the automatic
ground balancing procedure. Press-and-hold the GG button while pumping the
searchcoil up and down over the ground. Release the button when the sound evens
out. The GND BAL number on the bottom right of the screen is the detector's internal
setting which cancels out the minerals in the ground. Different soils in different areas
will require different GND BAL settings, so balance to ground before you search. See
the section on Ground Balancing for a detailed description of this procedure.
Refer to the Ground Balancing section of this manual for a more in-depth description.

Setting the Controls

As you adjust any of the controls, notice that the values on the bottom-right of the
display indicate the settings of the value you are changing.
If you are new to metal detecting, start with the GAIN and THRESHOLD controls at a
low enough setting that you do not hear too many unwanted sounds, like warble or a
loud hum. Set the GAIN at the 12:00 position, or less. Then set the THRESHOLD to a
position where you hear a very slight background hum, or if you prefer, dial the control
just left of that position to a setting where the detector is silent.

Unwanted Noise

Read the section on Electrical Interference.
The G 2 is a highly sensitive device.
It is intended for use outdoors. Indoor operation will subject it to electrical interference
from a wide variety of devices in the home or office.

Sweeping the Searchcoil

As you sweep the searchcoil over the ground, try to keep the searchcoil parallel to the
ground.
Avoid lifting the searchcoil at the end of your sweeps.
Operating in All Metal Mode continued on next page
16
GROUND BALANCING -Technical Info
Fe O BARGRAPH
3 4
The Fe O 7-segment bargraph indicates the amount of ground mineralization,
3 4
independent of type, expressed as an equivalent volume concentration of
magnetite (Fe O ). It updates every second. It is sensitive to motion and will give
3 4
the most accurate readings if you pump the searchcoil up and down several times
over the ground. The presence of metal or "hot rocks" will cause the readings to be
inaccurate. If you stop moving the searchcoil, the bargraph will go blank.
INDICATION RELATIVE
MINERALIZATION
7 Bars High
2 to 6 Bars Medium
1 Bar Very Low
none --
Magnetic susceptibility is expressed in micro-cgs units. In a saltwater environment
in the absence of iron minerals, the bargraph indicates relative electrical conductivity.
In soils with greater than 10,000 micro-cgs units magnetic susceptibility, the
signal from the soil may saturate, or overload, the circuitry. This will not harm
the detector but the machine will not be usable in that condition. The solution
is to hold the searchcoil several inches above the soil surface so it is not "seeing
as much dirt." By listening and watching you will know how high you need to
hold the searchcoil in order to avoid overload.
The highest magnetic susceptibilities are usually found in soils developed over
igneous rocks, in alluvial black sand streaks on beaches, and in red clay soils
of humid climates.
The lowest magnetic susceptibilities are usually found in white beach sands of
tropical and subtropical regions, and soils developed over limestone.
% Fe O SUSCEPTIBILITY
3 4
over 1 over 2500
.026 - 1.0 61 - 2,500
0.006 - .025 15 - 60
less than .006 less than 15
25