Related Manuals for Teknetics T2
Summary of Contents for Teknetics T2
- Page 1 Professional Metal Detector Comprehensive Operating Manual and Guide to Metal Detecting...
- Page 2 • Double-Filter Discrimination modes for searching in trashy areas • Trigger-actuated target pinpointing with variable audio pitch If you have any questions, or need assistance with your metal detector, Call 1-800-413-4131, and ask for Teknetics Customer Service. Revision Level 6.0 Copyright First Texas Product, L.P. February 9, 2007...
-
Page 3: Table Of Contents
Using Headphones (not included) ........7 Introduction to the Teknetics T General information . -
Page 4: Quick-Start
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting QUICK START Start using your T right out of the box Assemble the detector (see instructions beginning page 5-6). Install four AA alkaline batteries. All positive terminals point up. Turn the knob, located under the armrest, fully clockwise. - Page 5 TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting ASSEMBLY Remove all components from box. Battery Compartment Attach searchcoil to lower stem by Headphone Jack lining up the holes. Release Clip Push coil knob through hole and tighten knob gently.
-
Page 6: Assembly Instructions
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting Assembly (continued) Firmly tighten bottom locking collar to secure lower stem. 10. Attach cable to s-rod with upper Velcro strip 11. Tighten up coil knob to keep searchcoil from flopping. 12. Insert batteries. -
Page 7: Using Headphones (Not Included)
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting MECHANICALS (continued) Arm Rest Position on Pole: Remove the two bolts to position the arm rest farther forward or back, to adapt to your arm’s length. — To reinsert the bolts, spin and twist them into place. Be careful not to damage the power cable that runs through the aluminum tube. -
Page 8: Introduction To The Teknetics T
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting Introduction to the Teknetics T HIGH PERFORMANCE The Teknetics T is a multi-purpose high-performance computerized metal detector. It has the high sensitivity and ground cancellation features needed for professional gold prospecting, the discrimination responsiveness needed for serious relic hunting under difficult conditions, and visual target ID considered essential in searching for coins. -
Page 9: Specifications
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting SPECIFICATIONS Mechanical: S-rod with electronics housing mounted on handgrip, 3-piece breakdown, batteries under elbow, 2-way armrest adjustment — forward/backward & around forearm. Searchcoil: 11” (28 cm) open-frame elliptical double-D, waterproof. Batteries: 4 AA, alkaline or NiMH (not included). -
Page 10: Controls
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting CONTROLS ON-OFF & VOLUME Knob (Under the elbow) This knob turns the machine on or off, and controls Menu speaker volume and headphone Botton volume. Knob position has no effect on Settings detector’s sensitivity or susceptibility to... -
Page 11: Menu System
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting Controls (continued) searchcoil motion. This aids in pinpointing the exact location of objects which were found while searching in the All Metal or Discrimination Mode. When the trigger is pushed forward, FASTGRAB automatic ground cancellation is activated. -
Page 12: Ground Cancellation
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting GROUND CANCELLATION What is Ground Cancellation? All soils contain minerals. Signals from ground minerals are often tens or hundreds of times as strong as the signal from a buried metal object. The magnetism of iron minerals, found in nearly all soils, causes one type of interfering signal. - Page 13 TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting GROUND CANCELLATION (continued) MANUAL GROUND CANCELLATION In most situations, it is preferable to push the trigger switch to activate FASTGRAB automatic ground cancellation. Generally, it is best to first let the computer automatically cancel interference from ground minerals.
- Page 14 TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting GROUND CANCELLATION (continued) MANUAL GROUND CANCELLATION (continued) To perform the Manual Ground Cancellation operation, do the following: Select the MANUAL G.C. function The legend G.C. PHASE appears. The present ground cancellation setting is displayed (0-99).
-
Page 15: All Metal Mode
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting ALL METAL MODE The All Metal mode is more sensitive and offers better feel than the Discrimination mode, and is used to find all metal objects present in the ground. The searchcoil must be in motion for objects to be detected. -
Page 16: Discrimination Mode
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting DISCRIMINATION MODE The Discrimination Mode is used to eliminate from detection trash metal objects such as nails, aluminum foil, or pull-tabs. The searchcoil must be in motion for metal objects to be detected. -
Page 17: Discrimination Mode
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting DISCRIMINATION MODE (continued) 2+: Two tones. Similar to 1+, except that iron produces a low-pitched tone regardless signal strength. The discriminator is continuous. However, the iron tone feature relies on a combination of continuous and sampled processing. -
Page 18: Pinpoint Feature
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting PinPoint Feature After a buried target has been located using the All Metal or Discrimination modes, you want to pinpoint the exact location of the target in order to facilitate its recovery. Accurate target pinpointing will minimize digging. -
Page 19: Lcd Visual Display
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting LCD VISUAL DISPLAY In normal operation, when the searchcoil passes over a metal object, the electrical signature (2-digit I.D.) of the metal object is displayed on the numeric display for 4 seconds, unless superceded by another object sooner. -
Page 20: Target Depth
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting LCD VISUAL DISPLAY (continued) The target indicator arrows are coded for signal strength — bold arrow for strong signals, caret ) arrow for medium signals, and small triangle for weak signals. When sweeping back and forth to check a target, the indications corresponding to the strongest signals will usually be the most accurate. -
Page 21: Bar Graph
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting LCD VISUAL DISPLAY (continued) BAR GRAPHS Fe (magnetite) This bar graph displays the magnetic mineralization factor, or magnetic susceptibility, of the soil. Magnetic susceptibility is expressed in terms of the percent volume of the iron mineral magnetite, which most black sand is made of. -
Page 22: Capabilities & Limitations
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting CAPABILITIES AND LIMITATIONS DEPTH The T can detect U.S. coins to a depth of about 12-15 inches under good conditions. Large objects (55 gallon drums, manhole covers, etc.) can be detected to a depth of several feet. -
Page 23: Depth Reading
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting CAPABILITIES AND LIMITATIONS (continued) GROUND CANCELING To achieve maximum depth in both the ALL METAL and DISCRIMINATION modes, as well as when using the PinPoint feature, the T offers the ability to cancel ground minerals either by manual adjustment, or automatically using the FASTGRAB feature (see p.11). -
Page 24: Capabilities & Limitations
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting CAPABILITIES AND LIMITATIONS (continued) STEEL BOTTLE CAPS & FLAT IRON TRASH Modern motion-type target ID metal detectors usually have difficulty consistently identifying steel bottle caps and other flat iron trash objects. Double-D searchcoils also have a reputation for being unable to distinguish steel bottle caps from coins, and for being unable to eliminate steel bottle caps from detection. -
Page 25: Search Techniques
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting SEARCH TECHNIQUES Sweeping Searchcoil (this does not apply to Pinpointing with the trigger switch) Keep the searchcoil in motion to RIGHT detect targets. Sweep the searchcoil parallel to the ground; do not lift the searchcoil at the end of the sweep. -
Page 26: Estimating Target Size And Depth
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting SEARCH TECHNIQUES (continued) Narrow It Down To narrow the response further, position the searchcoil near the center of the response pattern, release the trigger, and then pull it again. Now you will only hear a response when the searchcoil is right over the top of the target. -
Page 27: False Signals And Chatter
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting SEARCH TECHNIQUES (continued) Estimating Target I.D. With a single sweep over a target, you will usually see a 2-digit target ID displayed on the LCD. Repeated sweeps back and forth over the target may cause the 2-digit target ID values to change with each sweep of the coil;... -
Page 28: Ground Minerals
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting SEARCH TECHNIQUES (continued) NUISANCE BURIED OBJECTS In some areas there is a lot of metallic trash which produces weak signals. These could include deeply buried objects, little bits and pieces of rusty iron and corroded foil. These items can be detected, but are difficult to pinpoint due to their depth and small size. -
Page 29: Adjusting Sensitivity
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting SEARCH TECHNIQUES (continued) HOT ROCKS A hot rock is a rock which causes the metal detector to sound off because the rock contains iron minerals. They come in two basic types. -
Page 30: Tips On Ground Canceling
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting SEARCH TECHNIQUES (continued) Tips on ground canceling When the T first turns on, the ground cancellation Phase Number is preset to 90. This will give a positive response on nearly all soils. If you search in the Discrimination mode, you will probably not have to cancel the ground. -
Page 31: Detecting Activities
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting Detecting Activities Coinshooting Coinshooting is searching for coins, usually in places like parks, schoolyards, church lawns, and people’s yards. In most places where coins are likely to be found, there is also a lot of aluminum trash like pull-tabs and bottle caps, as well as steel bottle caps and often nails. -
Page 32: Relic Hunting
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting Detecting Activities (continued) Relic Hunting (continued) Before you go relic hunting, obtain permission from the property owner. If you intend to hunt on public land, check first with the administrator to make sure it’s not illegal. Certain kinds of sites, on both public and private land, are protected by law from relic hunting. -
Page 33: Gold Prospecting
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting Detecting Activities (continued) Hillsides are the best areas for gold prospecting using a metal detector, because hillsides cannot be cleaned out by panning and dredging the way streams can. Also, gold on hillsides,... -
Page 34: Cache Hunting
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting Detecting Activities (continued) Cache Hunting A cache (pronounced “cash”) is an accumulation of money, jewelry, gold, or other valuables, which someone has hidden. When people bury a cache, they usually put it in a strongbox or in a jar. -
Page 35: Shallow Water Hunting
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting Detecting Activities (continued) Shallow Water Hunting (continued) Salt water is highly conductive, and produces a strong signal which is like that of metal. Therefore the T is not suitable for use in or over salt water. In order to use the T... -
Page 36: Warranty
TEKNETICS Comprehensive Operating Manual & Guide to Metal Detecting 5-YEAR LIMITED WARRANTY The T 2 metal detector is warranted against defects in materi- als and workmanship under normal use for five years from the date of purchase to the original owner.