Design Guide (For Zifi240 And Zibi240); The Installation Space; Product Clearances; Side-By-Side Installations - GE ZIFI240 Installation Instructions Manual

For models ZIFI240 and ZIBI240 with Custom Door Panels and Handles

THE INSTALLATION SPACE

Locate
Outlet
8-1/2"
10-1/2"
9"
9" Max.
34-1/2"-35"
Max.
1-1/2"
1-1/2"
23-3/4" Min.
NOTE: If installing between
frameless cabinets, a 1/2"
wide filler strip or side panel
may be needed on the hinge
side. The filler strip will act as
a spacer between the door
case and adjacent cabinet
and will prevent interference
with the cabinet door swing.
The width of the opening
must include the filler panels.
The cutout depth should be 24"
The cutout dimensions shown allow for a full door
swing and access to the pull-out racks when installed
in standard 24" deep cabinets.
• All models may be used freestanding.
• In a standard 24" opening, the refrigerator door will
protrude 1-3/4" forward of the adjacent cabinets.
Additional Specifications
• A 120 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch circuit
or circuit breaker is recommended. Install a properly
grounded 3-prong electrical receptacle recessed into
the back wall as shown. Electrical must be located on
rear wall as shown. NOTE: GFCI (ground fault circuit
interrupter) is not recommended.
Black or Stainless Steel Toekick Options
• These products are shipped with a stainless steel toekick
and a black toekick. For shipping purposes, one of the
toekicks will be secured to the back of the unit, and the
second will be installed on the unit. Keep the unused
toekick and any unused parts for future use.

SIDE-BY-SIDE INSTALLATIONS

For a complete refreshment center, install a Fresh-Food Refrigerator
beside a Double Drawer Refrigerator, Beverage Center or Wine Chiller/
Wine Reserve. Or, install a Refrigerator with Icemaker beside
a Wine Chiller/Wine Reserve.
• A side-by-side installation requires at least a 47-1/2" wide opening.
No trim kits required.
• Products must operate from separate, properly grounded receptacles.
Design Guide
NOTE:
24"
Water line location
for ZIBI240 or
ZIBS240 model only
34-1/4"
to 34-3/4"
24-7/8"
23-3/4"

PRODUCT CLEARANCES

The Fresh-Food Refrigerator or Bar Refrigerator with
Icemaker is factory set for a 110° door swing.
When installed in a corner:
• Allow 16" minimum clearance on the hinge side
for a full 110° door swing.
• Allow 4-1/2" min. clearance on the hinge side for
the 90° door swing and to allow racks to slide out.
NOTE: Custom handle clearances may vary.
16" Minimum to Wall
110° Door
Swing
110°
NOTE: Right hand models illustrated. Allow the same
clearances on the opposite side for left hand fresh food
models ZIFI240 and ZIFS240 only. Models ZIBI240 and
ZIBS240 are not available with left hand door swing.
• Test the door swing. Carefully open and close
the door. The door should not rub or catch on adjacent
cabinetry. NOTE: When installing custom panel and
handle, use above clearances as a general guide but
adjust according to the installation.
Choose the location:
• These products may be closed in on the top and
three sides as long as the front is unobstructed for
air circulation and proper access to the door.
• Do not install these products where the temperature will
go below 55°F (13°C) or above 90°F (32°C).
• These products are not designed to be stacked one
over the other.
ZTBSS1—Monogram stainless steel tubular handle
for 3/4" thick custom panels. Order this kit from your
Monogram supplier.
34-1/2"-35"
5
90° Door
21-5/8"
Swing
23-5/8"
90°
4-1/2" Minimum to Wall
Locate
Outlet
10-1/2" 10-1/2"
24"
14"
9" 9"
15"
1-1/2"
47-1/2" Min.