1. Manuals
  2. Brands
  3. Integral Audio Manuals
  4. Subwoofer
  5. 1101S
  6. Installation manual

Integral Audio 1101S Installation Manual

Mini cooper hardtop 2002-2006 (r50) with harmon/kardon audio
Hide thumbs Also See for 1101S:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Manual
Enlarged version
PRINTING INSTRUCTIONS: LANDSCAPE ORIENTATION, FIT TO PAGE
INSTALLATION GUIDE
MODEL 1101S SUBWOOFER SYSTEM
MINI Cooper Hardtop 2002-2006 (R50)
with harmon/kardon audio
INSTALLATION
TIME
4
Hrs
!
IMPORTANT
•
Read this Installation Guide completely before beginning the installation.
•
This is a guide - your vehicle may vary. ALWAYS check behind panels &
components before drilling, cutting, or screwing into any part of a vehicle.
INSTALLATION
SKILL LEVEL
DIFFICULTY
REQUIRED
3
DIY
OUT OF
5
Contents
OVERVIEW .................................................................................... 2
BEFORE YOU BEGIN! . .................................................................. 2
WHAT'S IN THE BOX .................................................................... 3
TOOLS YOU WILL NEED .............................................................. 5
INSTALLATION:
V
.................................................................. 6
....................................................................... 8
TROUBLESHOOTING ................................................................. 13
.......................................... 7
w
...................................... 9
IRING
............................................ 10
............................................ 11
............................. 12
ETTINGS

Advertisement

Table of Contents
loading

Related Manuals for Integral Audio 1101S

Summary of Contents for Integral Audio 1101S

  • Page 1: Table Of Contents

    PRINTING INSTRUCTIONS: LANDSCAPE ORIENTATION, FIT TO PAGE Contents OVERVIEW ..................2 BEFORE YOU BEGIN! ..............2 WHAT’S IN THE BOX ..............3 INSTALLATION GUIDE TOOLS YOU WILL NEED .............. 5 INSTALLATION: MODEL 1101S SUBWOOFER SYSTEM A. P ..............6 REP ThE EhICLE B. R & G .......... 7 UN ThE...

  • Page 2: Overview

    Overview Before You Begin! • MINI C 1101S hESE NSTRUCTIONS OMPLETELy hIS GUIDE COVERS INSTALLATION OF ThE OOPER ODEL 2002-2006 MINI C (R50) UBwOOFER ySTEM IN OOPER ARDTOPS wITh ThE • ISCONNECT ThE EGATIVE ATTERy ERMINAL ARMON ARDON SPEAkER STEREO •...

  • Page 3: What's In The Box

    What’s In The Box ELECT OMPONENTS FOR DENTIFICATION OMPONENTS hOwN ELOw I. M 1101S S odel ubwoofer ncloSure II. I IaSw26-4 10” S ntegral udIo ubwoofer III. arc a KS125.2 MInI a udIo MplIfIer IV. f alSe loor anel V. S ubwoofer ncloSure ardware ERMINAL UP w...

  • Page 4: Tools You Will Need

    Tools You Will Need a. w trIpper rIMper b. t • T50 c. e lectrIc rIll d. d rIll bItS • 1/8” • 7/16” e. w rencHeS ocKetS • 7/16” • 8 • 10 • 19 llen rencH g. e ’...

  • Page 5: Prep The Vehicle

    A. PREP THE VEHICLE 5. r eMoVe The outside of each seat back has a pin that sits in a “T” shaped keyway. Rotate each seat back up to 1. r & f eMoVe arcel Helf loor anel about 45 degrees and pull toward the center of the Detach straps (1) and slide the parcel shelf out of vehicle to release.

  • Page 6: Run The Power & Ground Wires

    9. d 13. r etacH rIVerS eMoVe IgHt Remove the Torx T-50 bolt. Remove the metal rod Repeat the previous three steps for the Right Side of that secures the bottom of the seat belt. the vehicle. See Previous Images B. RUN THE POWER & GROUND WIRES 10. r eMoVe part...

  • Page 7: Signal Wiring

    C. SIGNAL WIRING 17. I 2) nStall older Cut a length of Power Wire to run from the fuse holder to the battery. Strip the length of the Power 21. I nput Ignal IrIng VerVIew Wire and both ends. Crimp the red 5/16” Gold Ring The input signal connection is made by tapping into Terminal to one end.

  • Page 8: Mount Amplifier & Connect

    28. H eatSHrInK onnectIon Amplifier Signal Connections 29. Slide the heatshrink tubing over the ends of the Signal : HK Amp Wire Color: Pin: Connect To: Posi-taps. Using a small torch or lighter, gently Rear Left ++ Blue w/ Red Stripe Pigtail 1 White and evenly apply heat to the heatshrink tubing until it shrinks securely over the Posi-tap connections.

  • Page 9: Install The Enclosure Mounts

    E. INSTALL THE ENCLOSURE MOUNTS 33. I nStall MplIfIer racKet part Leaving the Common Ground connection in place, put the two 6mm washers over the Common Ground 37. M racKet laceMent threaded stud, then the bracket, and finally the 6mm Temporarily replace the Rear Sill. Center the nut.

  • Page 10: Prep & Install The Enclosure

    41. I 45. M nStall Hreaded nSertS part ount loor upportS part Using a utility knife, carefully trim the PVC jacket out The floor supports are assembled with one Rubber of the center of the Self-Sealing Threaded Inserts as Stand-off, one Cup Washer, and one #10 x 1.5” Pan shown.

  • Page 11: Testing & Recommended Initials

    49. H eMoVe ncloSure To remove the enclosure, simply disconnect the speaker wire, unscrew the Rosette Thumbscrews, and remove. WARNING: Do not allow the Banana Plug connec- tors to short (touch each other) while the system is energized. G. TESTING & RECOMMENDED INITIAL SETTINGS 50. r & I econnect attery...

  • Page 12: Tips & Tuning

    Unfortunately the factory speakers aren’t capable of producing this exaggerated level of bass without creating distortion that affects the other frequencies the speaker is asked to produce. The Integral Audio subwoofer sys- tem allows the correction of this factory “tuning”. Because the subwoofer system has an independent volume control, the “Bass”...

Table of Contents