Advertisement
Assembly & User Instructions
Mirage 38,200Btu
Heat Focusing Patio Heater
These instructions are for your safety. Please read them
thoroughly before use and retain them for future reference
DANGER:
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from the
appliance and immediately call your gas
supplier or fire department.
WARNING:
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
An LP-cylinder not connected for use shall
not be stored in the vicinity of any other
appliance.
WARNING:
For Outdoor Use Only.
WARNING:
Improper installation, adjustment, alteration,
service or maintenance can cause
injury or property damage.
Read the installation, operating and
maintenance instuctions thoroughly before
installing or servicing this equipment.
We provide a Customer Support Service.
If you have any queries please contact us
on info@uig.biz or tel. (678) 534 2876
or visit our website www.uig.biz
Advertisement
Table of Contents
Related Manuals for Mirage HDMIRAGE10
Summary of Contents for Mirage HDMIRAGE10
- Page 1 Assembly & User Instructions Mirage 38,200Btu Heat Focusing Patio Heater These instructions are for your safety. Please read them thoroughly before use and retain them for future reference DANGER: If you smell gas: 1. Shut off gas to the appliance.
-
Page 2: Parts Supplied
Parts Supplied Description Illustration Qty Ref Description Illustration Qty Lower Base Support Pole Upper & Lower Cylinder Chamber Upper Supports Support Pole A,B and C A B C Cylinder Lantern Chamber Door Cylinder Parasol Side Chamber Wall Panels Cylinder Parasol T op Chamber T op Panel Reflector Handle... - Page 3 Fixings Supplied Description illustration Qty Ref Description illustration M6 Nut Washer M6x10 Dome M8x10 Bolt Head Bolt M6x12 Dome Hex Bolt Before You Start • Check the contents of the box and make sure you have all the parts and fittings listed.
-
Page 4: Assembly Step
Assembly step 1 Upper & Lower Cylinder Chamber M6 Bolt (C) Base x 1 Supports (A,B,C) Fix the cylinder chamber supports. (A,B,C) to corresponding location on the base with 6 M6 bolts (Ref. C). Cylinder chamber supports Base Page 3... - Page 5 Assembly step 2 M6 Nut (A) Lower M6x12 Support Pole Dome Hex Bolt (C) Fix lower support pole to cylinder chamber supports as shown using 6 M6 bolts (Ref. C) and 6 M6 nuts (Ref. A) M6x12 Bolt Cylinder chamber supports Page 4...
- Page 6 Assembly step 3 M6Nut M6x10 Dome Cylinder Head Bolt (B) Chamber Wall Fit the cylinder chamber wall to the cylinder chamber supports using 6 dome head bolts (Ref. B) and 6 M6 nuts (Ref. A) Cylinder Chamber Wall Cylinder Chamber Supports Page 5...
- Page 7 Assembly step 4 Cylinder Chamber door Hang door on hinges. Ensure correct alignment and tighten bolts securely. Cylinder Chamber door Hinges Page 6...
- Page 8 Assembly step 5 M6 x 10 Cylinder M6 Nut Dome Bolt (B) Chamber Top Fit cylinder chamber top onto cylinder chamber support legs using 3 dome head bolts (Ref. B) and M6 nuts (Ref. A) Cylinder Chamber Top M6 Nut M6x10 Dome Head Bolts Page 7...
- Page 9 Assembly step 6 M6 x 12 Dome Hex Bolt (C) Fit upper support pole to lower suport pole using 3 x m6x12 dome hex bolts (Ref.C) Upper Support Pole M6x12 Dome Hex Bolts Page 8...
- Page 10 Assembly step 7 M6 x 12 Dome Hex Bolt (C) 1. Feed the lantern hose down the support pole and secure lantern to support pole using 4 M6x12 Dome Hex Bolts. (Ref. C) Lantern M6x12 Dome Hex Bolts Page 9...
-
Page 11: Check For Leak
Assembly step 8 Regulator Connect the lantern hose to the regulator hose and secure tightly with adjustable wrenches. Then attach the regulator to the cylinder, turn clockwise to tighten it securely. Place cylinder in position as shown. Connect securely with adjustable wrenches Check for Leak... - Page 12 Assembly step 9 Reflector handle Fitting reflector handle Retaining Pin R Clip Reflector handle Heat focus reflector bracket Remove R clip and retaining pin Fit reflector handle Secure with retaining pin and R clip. Page 11...
- Page 13 Assembly step 10 M8x10 Side M6 Nut Dome Washer Bolt Head Bolt Panel Panels Remove any protective layer and loosely screw parasol side panels together overlapping as shown with 18 dome head bolts and nuts (B,A), fix the top panel to the top of assembled side panels. Tighten all nuts. Fix assembled parasol onto top of Parabolic Reflector Bracket using 3 M8x10 Bolts (E) and M8 washers (D).
- Page 14 For all appliances: • The heater, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. • Certain materials or items, when stored under the heater, will be subjected to radiant heat and could be seriously damaged.
- Page 15 Leak Testing • To be performed in a well ventilated area. • Confirm all control knobs are in the off position. • Open the gas control valve on the bottle or regulator. • Check the leaks by brushing a solution of 1/2 water and 1/2 soap over the gas system joints, including all valve connections, hose connections and regulator connections.
-
Page 16: Use Instructions
Use Instructions Before proceeding make sure you understand the warnings section of this manual. Lighting instructions: • Turn on gas supply at cylinder. • Push dial in and turn to position • While dial is held pressed in at position , press spark button repeatedly to ignite the burner. •... - Page 17 • When using the heater after extended periods of storage, re-attach the reflector. The heater should never be operated without the reflector in place. • If the heater is to be stored indoors, the gas bottle must be disconnected and left outside.
- Page 18 CAUTION • It is normal for the heater to smoke during the first few minutes of use. • Regularly clean your patio heater after every use. • If you smell gas – turn off the appliance and extinguish all flames. If the odour continues, immediately contact your gas supplier.