Do you have a question about the 58259 and is the answer not in the manual?
Questions and answers
Sakile Thomas
June 8, 2025
i have a best way heater when the power is on it's say Ed
WHEN YOU press the power button it says on, but the water temperature remains unchanged, left heater running for approxcimatly 3hr and no change the the tempreture of the water
1 comments:
Mr. Anderson
June 8, 2025
The "Ed" code on the Bestway heater model 58259 indicates that the heater is in standby mode and not yet turned on. To resolve this and begin heating, press and hold the power symbol on the heater until it switches from "Ed" to "On".
If the water temperature is not increasing, ensure the pump is running and properly connected to the heater. Heating a large volume of water may take at least 24 hours. Use a solar cover to retain heat when the pool is not in use.
This answer is automatically generated
Levi
May 15, 2025
Hi the heater is leaking water from the from bit of the unit itself, is this normal
1 comments:
Mr. Anderson
May 22, 2025
No, it is not normal for the Bestway heater model 58259 to leak water from the front of the unit. Possible causes of leaking include loose hose clamps, incorrectly positioned or damaged hose O-rings, or a broken hose. These issues should be checked and corrected.
This answer is automatically generated
Nicola Lewis
July 9, 2025
When i turn it on its says ed when i hold it down and press it say E1
евгений петрович солдатенко
June 29, 2025
можно ли использовать фильтр насос bestway 1249 л\час
Валерий
June 4, 2025
Добрый день, при включении начинает мигать сигнальная лампа 1 раз в сек без сигнала. Нагрев не работает. Датчик потока в норме, давление воды в норме. Сброс настроек делал. Первое включение было все ОК, потом часа через 4-5 началась это проблема.
• To reduce the risk of electric shock, do not use extension cords to connect • Please examine all equipment before use. Notify Bestway through our the unit to electric supply; provide a properly located outlet. customer service address listed on this manual for any damaged or •...
Page 4
Pedestal Fixing The pool heater must be vertically fixed on ground or a certain pedestal made of wood or concrete before it can be used. There should be two holes, 8mm in diameter on the pedestal, the space between which should be 254mm. Put the pool heater on the pedestal and fix them together with bolts and nuts.
Page 5
Zip code: instructions. Bestway is not responsible for economic loss due to water or chemical costs. Bestway City: will not replace any products deemed to have been neglected or having been used outside of the owner manual guidelines.
Page 6
E-mail: aftersales@bestway-uk.com E-mail: assistenza@bestway-europe.com E-mail: austria@bestway-service.com www.bestway-uk.com The Netherlands Belgium & Luxembourg Bestway Central & South America Ltda Tel: 08002378929 Tel: 0 800 20 132 Salar de Ascotan 1282, Parque Enea, Fax: (+31) 887878969 Fax: (+32) 02 6104411 Pudahuel, Santiago, Chile E-mail: dutchservice@bestway-europe.com...
Need help?
Do you have a question about the 58259 and is the answer not in the manual?
Questions and answers
i have a best way heater when the power is on it's say Ed WHEN YOU press the power button it says on, but the water temperature remains unchanged, left heater running for approxcimatly 3hr and no change the the tempreture of the water
The "Ed" code on the Bestway heater model 58259 indicates that the heater is in standby mode and not yet turned on. To resolve this and begin heating, press and hold the power symbol on the heater until it switches from "Ed" to "On".
If the water temperature is not increasing, ensure the pump is running and properly connected to the heater. Heating a large volume of water may take at least 24 hours. Use a solar cover to retain heat when the pool is not in use.
This answer is automatically generated
Hi the heater is leaking water from the from bit of the unit itself, is this normal
No, it is not normal for the Bestway heater model 58259 to leak water from the front of the unit. Possible causes of leaking include loose hose clamps, incorrectly positioned or damaged hose O-rings, or a broken hose. These issues should be checked and corrected.
This answer is automatically generated
When i turn it on its says ed when i hold it down and press it say E1
можно ли использовать фильтр насос bestway 1249 л\час
Добрый день, при включении начинает мигать сигнальная лампа 1 раз в сек без сигнала. Нагрев не работает. Датчик потока в норме, давление воды в норме. Сброс настроек делал. Первое включение было все ОК, потом часа через 4-5 началась это проблема.