Superior VRL4543ZMN Installation And Operation Instructions Manual page 17

MODE Zone: Blank
ROOM TEMP Zone: Blank
SET TEMP Zone: Blank
LIGHT Zone: Blank
FAN Zone: Blank
TIME/PROG Zone: Day of Week, or Time of Day will Flash
AUX Zone: Blank
FLAME Zone: Blank
• Temperatures may be displayed in degrees F (factory
default) or degrees C. Press the up and down buttons
simultaneously to change between degrees F. and C.
MODES OF OPERATION
Operation modes:
• MANUAL OFF
• MANUAL ON
The modes may be cycled in the order above by pressing the MODE
Zone or the MODE/SET Button.
MANUAL OFF MODE
• Transmits flame OFF command.
• LCD Displays:
• MODE Zone: OFF is displaye
• ROOM TEMP Zone: Measured temperature is displayed
• SET TEMP Zone: Blank
• LIGHT Zone: LIGHT and light setting level is displayed
• FAN Zone: Blank
• TIME/PROG Zone: Current day indicator and current time
is displayed
• AUX Zone: Blank (AUX function is omitted on this control)
• FLAME Zone: Blank
MANUAL ON MODE:
• Transmits flame ON command
• LCD Displays:
• MODE Zone: ON is displayed
• ROOM TEMP Zone: Measured temperature is displayed
• SET TEMP Zone: Blank
• LIGHT Zone: LIGHT and light setting level is displayed
• FAN Zone: FAN and fan setting level is unused
• TIME/PROG Zone: Current day indicator and current time
is displayed
• AUX Zone: Blank (AUX function is omitted on this control)
• FLAME Zone: A&B Flame Icons and flame setting level
numbers are displayed
THERMOSTAT Mode:
NOTE: THE FACTORY DEFAULT SETTING DISABLES THERMOSTAT
MODE.
• Will cycle flame on and off based on room and set temperatures.
Will transmit ON command if SET TEMP (+SWING) is higher
than ROOM TEMP and will transmit OFF command if SET TEMP
(-SWING) is lower than ROOM TEMP.
• Built-in thermostat will measure room temperature.
• All programming should be written for deg. F and converted to
deg. C when selected.
126861-01C
REMOTE CONTROL OPERATION
•
•
•
EXAMPLE:
Set Temperature
Set Temperature (72)
•
•
o
o
o
o
o
o
o
o
•
o
o
o
Superiorfireplaces.US.com
Continued
Temperatures may be displayed in degrees F (factory default) or
degrees C. Press the UP and DOWN Buttons simultaneously to
change between degrees F and C.
SET TEMP: While in THERMOSTAT mode, press the UP or DOWN
Button to change the SET TEMP (45-90 deg. F, 7-32 deg. C);
the new set temperature will automatically be accepted after 2
seconds. The factory default SET TEMP is 45 deg. F.
SWING Temperature: This model does not allow for SWING
temperature adjustment. This model utilizes thermostatic flame
modulation that will modulation the main flame based on the
difference between room temperature and set temperature:
o Important - factory SWING TEMPERATURE setting is 2
degrees. The thermostatic flame modulation feature will not
allow this SWING to be changed.
Room Temp.
74F
73F
72F
71F
70F
69F
68F
67F
Manual Flame Adjustment while in THERMOSTAT mode: Flame-
A will be the only flame setting that is adjusted automatically.
Flame-A and Flame-B may be manually adjusted while in thermo-
stat mode. If Flame-A is manually adjusted while in thermostat
mode, it will override the automatic flame setting until the flame
cycles off, then back ON thermostatically; when the flame cycles
ON again, automatic flame adjustment will resume (Flame-B
setting will remain as-set by the user). Automatic flame adjust-
ment will also resume if the operational mode is cycled out of,
then back into THERMOSTAT mode or if the SET temperature
is changed.
THERMOSTAT OFF LCD Displays:
MODE Zone: THERMO and OFF is displayed
ROOM TEMP Zone: Measured temperature is displayed
SET TEMP Zone: SET TEMP is displayed
LIGHT Zone: LIGHT and light setting level is displayed
FAN Zone: Blank
TIME/PROG Zone: Current day indicator and current time is
displayed
AUX Zone: Blank (AUX function is omitted on this control)
FLAME Zone: Blank
THERMOSTAT ON LCD Displays:
MODE Zone: THERMO and ON are displayed
ROOM TEMP Zone: Measured temperature is displayed
SET TEMP Zone: SET TEMP is displayed
Flame Level
OFF
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
17