D-Link DVG-5102S User Manual
D-Link DVG-5102S User Manual

D-Link DVG-5102S User Manual

D-link dvg-5102s voip telephone adapter
Hide thumbs Also See for DVG-5102S:

Advertisement

Quick Links

DVG-5102S
VoIP Telephone Adapter
User's Manual
Version 1.2
(16 Sept. 2014)

Advertisement

Table of Contents
loading

Subscribe to Our Youtube Channel

Summary of Contents for D-Link DVG-5102S

  • Page 1 DVG-5102S VoIP Telephone Adapter User’s Manual Version 1.2 (16 Sept. 2014)
  • Page 2 Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of D-Link Corporation/D-Link Systems Inc.; Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
  • Page 3: Table Of Contents

    Contents 1. Introduction ................................ 4 1-1 Product Overview ............................4 1-2 Hardware Description ..........................5 2. Getting Started ..............................7 2-1 SETUP ..............................10 2-1-1 Internet Setup ..........................10 2-1-2 LAN Settings ..........................13 2-2 MAINTENANCE............................15 2-2-1 Device Management ........................15 2-2-2 Backup and Restore ........................
  • Page 4: Introduction

    The DVG-5102S can be configured a fixed IP address or it can have one dynamically assigned by DHCP or PPPoE. It adopts either the G.711, G.726, G.729A, G.723.1 and G.722 voice compression format to save network bandwidth while providing real-time, toll quality voice transmission and reception.
  • Page 5: Hardware Description

    When a phone is ringing, the indicator will blink. Note: When starting up DVG-5102S, all indicators will light up. After about 40 seconds, the Register indicator will blink in green. If the Alarm indicator continues to blink, it means DVG-5102S is currently communicating with ISP and has yet to obtain an IP address or fail to register to VoIP Service Provider.
  • Page 6 DVG-5102S User’s Manual Telephone Interface Description Rear Panel Phone Port: Connect to your phones using standard phone cabling (RJ-11). WAN: Connect to your broadband modem / router using an Ethernet cable. LAN: Connect to your Ethernet enabled computers using Ethernet cabling.
  • Page 7: Getting Started

    Internet Explorer and enter the IP address of the DVG-5102S. *Statics IP: 192.168.8.XXX, the “XXX” can be any number from 1~253 except 254 cannot be used* If the DVG-5102S is connected behind a router, the IP address of the router is determine by the router’s DHCP Server.
  • Page 8 DVG-5102S User’s Manual MAINTENANCE VoIP TA Web Configuration During configuration, please follow the Setup Hint for some specific procedure in case the VoIP TA fails to make the changes active. Situation 1: (example: Internet Setup) Setup Hint: Select DHCP WAN Setup.
  • Page 9 DVG-5102S User’s Manual MAINTENANCE Situation 2: (example: Enable IP Filtering) Setup Hint: Click “Enable IP Filtering” check box to open the main screen. Click “Add” to enter an entry. After Adding an entry, you have to click “Apply”. Don’t forget to click “Apply” which in the field of “Enable IP Filtering”.
  • Page 10: Setup

    DVG-5102S User’s Manual MAINTENANCE 2-1 SETUP 2-1-1 Internet Setup WAN (Wide Area Network) Settings are used to connect to your ISP (Internet Service Provider). The WAN settings are provided to you by your ISP and oftentimes referred to as "public settings". Please select the appropriate option for your specific ISP.
  • Page 11 DVG-5102S User’s Manual MAINTENANCE DHCP: Select this option if your ISP (Internet Service Provider) provides you an IP address automatically. Cable modem providers typically use dynamic assignment of IP Address. The Host Name field and Vendor Class ID are optional but may be required by some Internet Service Providers.
  • Page 12 DVG-5102S User’s Manual MAINTENANCE SETUP → Internet Setup VoIP Connection Interface: Select a WAN interface for DVG-5102S VoIP traffic. SETUP → Internet Setup Factory Default MAC Address: The original MAC address of the VoIP Router. Your MAC Address: It is left blank as you log-in via the WAN port.
  • Page 13: Lan Settings

    Note: If you set a LAN port to be bridge mode that the LAN port will be bundled with WAN. If you would like to connect to DVG-5102S at the bridged LAN port you must enter WAN port IP. VLAN ID: Assign a VLAN ID for DVG-5102S to transit traffic through-out at WAN port for WAN-LAN...
  • Page 14 DVG-5102S User’s Manual MAINTENANCE bridge mode. The packets are un-tagged at LAN port and added tag at WAN port. Note: It is not allowed to change VLAN ID for NAT mode LAN ports. The VLAN ID of NAT LAN ports are bundled with WAN 1 which assigned at Internet Setting page. The packets are un-tagged at LAN port and added tag at WAN port.
  • Page 15: Maintenance

    DVG-5102S User’s Manual MAINTENANCE 2-2 MAINTENANCE 2-2-1 Device Management MAINTENANCE → Device Management Password: By default there is no password configured. It is highly recommended that you create a password to keep your router secure. 2-2-2 Backup and Restore Save and Reboot MAINTENANCE →...
  • Page 16 DVG-5102S User’s Manual MAINTENANCE Backup Configurations Template File MAINTENANCE → Backup and Restore Click the Backup Settings button to save your current settings to a template file for editing. Update Settings MAINTENANCE → Backup and Restore To restore a system settings file, click on Browse to search the local hard drive for the file to be used.
  • Page 17: Diagnostics

    DVG-5102S User’s Manual MAINTENANCE 2-2-3 Diagnostics Use “Ping” to verify if a remote peer is reachable. Enter a remote IP address and click “Test” to ping the remote host. The result would be shown on Result Table MAINTENANCE → Diagnostics...
  • Page 18: Status

    DVG-5102S User’s Manual STATUS 2-3 STATUS 2-3-1 Device Info STATUS → Device Info For System Information, it shows Model Name, Time and Date and Firmware Version. For WAN Port Information, it shows IP address, subnet mask, default gateway and DNS server. If you use PPPoE to obtain IP, you will know if the IP is obtained through this method.
  • Page 19: Voip Status

    DVG-5102S User’s Manual STATUS STATUS → Device Info For Hardware, it shows the hardware platform and driver version. 2-3-2 VoIP Status STATUS → VoIP Status For Port Status, it includes if each port registers to Proxy successfully, the last dialed number, how many calls each port has made since the VoIP TA is start, etc.
  • Page 20: Statistics

    DVG-5102S User’s Manual STATUS 2-3-3 Statistics STATUS → Statistics Display the information of the last call made. Press Refresh button to get the latest RTP Packet Summary. 2-3-4 Logout If setting or parameter has been changed, remember to save the changes before you logout the configuration menu.
  • Page 21: Configuring The Voip Ta Through Ivr

    DVG-5102S User’s Manual VoIP Router Configuration-IVR 3. Configuring the VoIP TA through IVR VoIP transmits voice data (packets) via the Internet, hence the condition and status of the network environment is relatively important to the telecommunications quality. If any one of the parties involved in VoIP communications has insufficient bandwidth or frequent packet loss, the telecommunication quality will be poor.
  • Page 22: Ivr Functions Table

    DVG-5102S User’s Manual VoIP Router Configuration-IVR a new IP address) enter 192*168*1*2 (new IP address). Save Settings When all setting procedures are completed, dial 509 (Save Settings) from phone keypad. Wait for about three seconds, you should hear a voice prompt “1 (one).” You can now hang up the phone and please reboot the VoIP TA to enable the new settings.
  • Page 23: Ip Configuration Settings-Set The Ip Configuration Of The Wan Port

    DVG-5102S User’s Manual VoIP Router Configuration-IVR 3-2 IP Configuration Settings—Set the IP Configuration of the WAN Port Static IP Settings Note: Complete static IP settings should include a static IP (option 1 under 114), IP address (111), Subnet Mask (112), and Default Gateway (113). Please contact your Internet Service Provider (ISP) if you have any question.
  • Page 24 DVG-5102S User’s Manual VoIP Router Configuration-IVR Select a PPPoE After entering IVR mode, dial 114. When voice prompt plays “Enter value,” dial 3 (to select PPPoE). PPPoE Account Settings After entering IVR mode, dial 121. When voice prompt plays “Enter value”, enter the account number followed by”#”.
  • Page 25: Pppoe Character Conversion Table

    (high-lighted) of each pair of the column (“Input Key”) represents the codes to be entered for the corresponding numbers, alphabets or symbols. For example, to enter “D-Link” according to the table below, enter: 148322495451 Numbers...
  • Page 26: Dialing Principles

    DVG-5102S User’s Manual Appendix 4. Dialing Principles 4-1 Dialing Options Dial the phone number which you want to call and press # to call out immediately. Note that if the “# (pound)” not dialed, the number will be called out after 4 seconds by default. The period between number dialed and call out is named “Inter Digits Timeout”.
  • Page 27: Routing

    DVG-5102S User’s Manual Appendix 4-3 Routing To achieve maximum flexibility, the number dialed will be looked up in several tables defined by VoIP TA. If no match is found from Digit Map Table, it will then look up the number from another table and to the registered VoIP Service Provdier.
  • Page 28 DVG-5102S User’s Manual Appendix Start Enter a phone number (D#) Is (D#) defined Change the number to in Digit Map Global Number. table? Is (D#) or Global Number defined in Phone Book table? Is (D#) or Global Number defined in Server 1?
  • Page 29: Appendix

    DVG-5102S User’s Manual Appendix Appendix Product Features  One 10/100Mbps auto-negotiation, auto-crossover RJ-45 Ethernet port  Support static IP, PPPoE and DHCP address assignment and dynamic DNS (DDNS)  QoS: IP TOS (Type of Services) and DiffServ (Differentiated Services) for both SIP signaling and RTP ...
  • Page 30 DVG-5102S User’s Manual Appendix STUN/UPnP status Hardware / software information  Firmware Upgrade through HTTP, TFTP, FTP and proprietary image server  Configuration Backup/Restore  Reset button (with restore factory default function)  Front Panel LED : voice ports, WAN, LAN, Register, Power, Alarm ...

Table of Contents