1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Adapter
  5. DVG-2001S
  6. Quick user manual

D-Link DVG-2001S Quick User Manual

Voip terminal adapter
Hide thumbs Also See for DVG-2001S:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Manual, Manual
DVG-2001S VoIP Terminal Adapter
Quick User Guide
Version 1.0

Advertisement

Table of Contents
loading

Related Manuals for D-Link DVG-2001S

Summary of Contents for D-Link DVG-2001S

  • Page 1 DVG-2001S VoIP Terminal Adapter Quick User Guide Version 1.0...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION ..................... 1 PACKAGE CONTENTS .................. 1 CONNECTIONS ....................2 LEDS....................... 3 FEATURES ..................... 4 USING THE CONFIGURATION WIZARD............5 A. H > WAN > D IP A .............. 6 YNAMIC DDRESS B. H > WAN > S IP A ..............

  • Page 3: Introduction

    Ethernet Cable (the DVG-2001S’s Ethernet port is Auto-MDIX) If any of the above items are missing, please contact your reseller. Note: Using a power supply with a different voltage rating than the one included with the DVG-2001S will cause damage and void the warranty for this product.

  • Page 4: Connections

    3. Connections The Ethernet Port (LAN) is auto MDI/MDIX, meaning you can use either a straight-through or a crossover Ethernet cable. Power Adapter Phone Connection Connect your Connect to your phone 12V 1.2A power using standard phone adapter here. cabling. Auto MDI/MDIX LAN Port Connect the Ethernet Factory Reset...

  • Page 5: Leds

    4. LEDs Phone LED This LED will light when a telephone is off the hook. A blinking LED indicates an incoming call is detected LAN LED Power LED An active LED indicates A solid light a link has been indicates a valid established.

  • Page 6: Features

    5. Features One Foreign Exchange Subscriber (FXS) POTS port (RJ-11 Jack) One NWay 10/100BASE-TX Fast Ethernet port for network connection Voice Activity Detection (VAD)/Comfort Noise Generation (CNG) Silence suppression to reduce bandwidth consumption Adaptive jitter buffer for smooth voice reception Lost packet recovery ability for improved voice quality Support QoS (Quality of Service) for voice quality guarantee Built-in PPPoE function to support dial-up connection for broadband...

  • Page 7: Using The Configuration Wizard

    6. Using the Configuration Wizard http://10.1.1.1 Whenever you want to configure your network or the DVG-2001S, you can access the Configuration Menu by opening the web-browser and typing in the IP Address DVG-2001S. DVG-2001S default IP Address is shown to the right: •...

  • Page 8: Home > Wan > Dynamic Ip Address

    A. Home > WAN > Dynamic IP Address Dynamic IP Address Choose Dynamic IP Address to obtain IP Address information automatically from your ISP. This option should be selected if your ISP has not supplied you with an IP address. This option is commonly used for Cable modem services.

  • Page 9: Home > Wan > Static Ip Address

    B. Home > WAN > Static IP Address Static IP Address Choose Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP.

  • Page 10: Home > Wan > Pppoe

    C. Home > WAN > PPPoE Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and pass- word. This option is typically used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection.
  • Page 11 Secondary This is an optional DNS Address entry to be used if the primary DNS fails. DNS Address Click Apply to set any changes made to the memory of the VoIP Terminal Adapter. Click Connect to initiate a PPPoE connection. Click Disconnect to end a PPPoE connection.

  • Page 12: Advanced > Voip > Server Configuration

    D. Advanced > VOIP > Server Configuration The VoIP Terminal Adapter can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). The screen shown to the right, along with those on the following pages are used to configure your router to communicate with the devices that will send and receive...
  • Page 13 Caller ID Delivery You can set this to YES or NO. This determines whether CID is received. Display CID You can set this to Enabled or Disabled. This determines whether to display Caller ID. Use the drop-down menu provided to select the desired time increment. Timer T2 You can set this to Enabled or Disabled.

  • Page 14: Advanced > Voip > Provisioning

    E. Advanced > VOIP > Provisioning Provisioning is a function that automatically updates your DVG-2001S’s VoIP configuration by using a TFTP server located on the Internet. If you have accesses to such a service, you will need to know the URL and Proxy...

  • Page 15: Advanced > Voip > Stun Configuration

    NAT. STUN is useful if you need to use the DVG-2001S behind a modem or router that provides the connection to your ISP and then to the Internet and does not support symetric NAT. You will need access to a STUN server on the Internet and its IP address to use STUN on the DVG-2001S.

  • Page 16: Advanced > Voip > User Agent

    G. Advanced > VOIP > User Agent The VoIP Terminal Adapter can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Same Phone Number Use this field to enable or disable the use of the same telephone number for the User Agent as for the Server Agent.

  • Page 17: Advanced > Voip > Peer To Peer

    H. Advanced > VOIP > Peer to Peer The VoIP Terminal Adapter can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Index This field assigns the telephone socket (on the back of the router) to the information entered in the User Agent.

  • Page 18: Advanced > Voip > Telephony

    Advanced > VOIP > Telephony The VoIP Terminal Adapter can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Out-of band Dual Tone Multi-frequency – The Dual Tone Multi-frequency DTMF Method (DTMF) mode sets how the router will handle the tones that your telephone makes when you push its buttons.

  • Page 19: Advanced > Misc

    J. Advanced > Misc. Signaling ToS Signaling ToS -ToS field value in UDP IP Packets carrying a SIP Message RTP ToS RTP ToS - ToS field value in UDP IP Packets carrying a RTP data Receive Gain Used to raise or lower the gain (volume) of signals that come in from the IP and are sent to the line-side or trunk-side interface.

  • Page 20: Tools > Admin

    K. Tools > Admin Change System Password To change the password used to access the web manager, type the New Password and Confirm Password to be certain you have typed it correctly. Click the Apply button activate password. System User Name remains “admin”,...

  • Page 21: Tools > System

    L. Tools > System Reset to Factory Default Click Reset to Factory Default to restore the settings.

  • Page 22: Tools > Firmware

    Please check the D-Link Support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site. Firmware Update Click on the link in this screen to find out if there is an updated firmware;...

  • Page 23: Tools > Config

    N. Tools > Config This screen allows you to backup and restore configuration files. Click Backup to initiate the backing configuration file. Click Upload to initiate the uploading configuration file once you have located it by...

  • Page 24: Tools > Save & Reboot

    O. Tools > Save & Reboot This screen allows you to save and reboot the VoIP Terminal Adapter. Click Reboot...

  • Page 25: Status > Device Info

    P. Status > Device Info This page displays the current information for the DVG-2001S. MAC Address: MAC address of the DVG-2001S IP Address: WAN/Public IP Address Subnet Mask: WAN/Public Subnet Mask Default Gateway: WAN/Public Gateway IP Address...

  • Page 26: Status > Stats

    The screen above displays the Traffic Statistics. Here you can view the amount of packets that pass through the DVG-2001S on the WAN port. The traffic counter will reset if the device is rebooted or can be reset by clicking the Reset button. To refresh...

  • Page 27: Status > Cable Tester

    R. Status > Cable Tester The VoIP Terminal Adapter offers you to conduct a Ping test by entering the IP address in the field below and then clicking the test button. .

  • Page 28: Help

    S. Help The Help tab will give basic information referring to various screens located in the VoIP Terminal Adapter. To view a specific section, click on its hyperlinked name. A new window of information will appear.

  • Page 29: Technical Specifications

    7. Technical Specifications Standards: IEEE 802.3 IEEE 802.3u Device Management: HTTP 1.0 Web-Based - Internet Explorer v6 or later; Netscape Navigator v6 or later; or other Java-enabled browsers DHCP Client Auto-provisioning Telnet TFTP Client Performance monitoring using DSP/Ethernet statistics Operating Temperature: º...
  • Page 30 Ext. Power Supply DC 12V, 1.2A Weight: 0.1225kg Warranty: 3 year (depends on D-Link global warranty policy) Telephony Support: Call Control Protocol – SIP (RFC 3261) CODEC – G.711 (A-law and U-law), G.723.1, G.726, and G.729A Echo Cancellation – G.168 DTMF Relay –...

  • Page 31: Frequently Asked Questions

    8. Frequently Asked Questions Why can´t I access the web based configuration? When entering the IP Address of the DVG-2001S (10.1.1.1), you are not connecting to the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself.
  • Page 32 Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) What type of cable should I be using? (continued) What´s the difference between a crossover cable and a straight-through cable? The wiring in crossover and straight-through cables are different.
  • Page 33 Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) When to use a crossover cable and when to use a straight-through cable: Computer to Computer – Crossover Computer to an normal port on a Hub/Switch – Straight-through Computer to an uplink port on a Hub/Switch –...
  • Page 34 Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) Disable any Internet security software running on the S t e p 2 computer. Software firewalls like Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, etc. might block access to the configuration pages.
  • Page 35 Check your IP Address. Your computer must have an IP Address in the S t e p 4 same range of the device you are attempting to configure. Most D-Link devices use either 10.0.0.1 or the 192.168.0.X range. How can I find my IP Address in Windows 95, 98, or ME? Step 1 Click on Start and then click on Run.
  • Page 36 Click OK to close the IP Configuration window. (continued) Check your IP Address. Your computer must have an IP S t e p 4 Address in the same range of the device you are attempting to configure. Most D-Link devices use either 10.0.0.1 or the 192.168.0.X range.
  • Page 37 Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) How can I find my IP Address in Windows 2000/XP? Step 1 Click on Start and select Run. Step 2 Type cmd then click OK. Step 3 From the Command Prompt, enter ipconfig.
  • Page 38 Link device uses 10.1.1.1. Make sure you take note of your computer´s Default Gateway IP Address. The Default Gateway is the IP Address of the D-Link VoIP Terminal Adapter. By default, it should be 10.1.1.1. How can I assign a Static IP Address in Windows XP? Step 1 Click on Start >...
  • Page 39 Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) can I assign Static IP Address Windows 2000? (continued) Click “Use the following IP Address” and enter an IP Address that is on the same subnet as the LAN IP Address on your VoIP Terminal Adapter.
  • Page 40 Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) can I assign Static IP Address Windows 98/Me? Step 1 From the desktop, right-click on the Network Neighborhood icon (Win ME - My Network Places) and select Properties. Highlight TCP/IP and click the Properties button.
  • Page 41 Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) can I assign Static IP Address Windows 98/Me? Step 2 Click Specify an IP Address. Enter in an IP Address that is on the same subnet as the LAN IP Address on your VoIP Terminal Adapter.
  • Page 42 Access the web management. Open your web browser and enter the IP S t e p 5 Address of your D-Link device in the address bar. This should open the login page for the web management. Follow instructions to login and complete the...
  • Page 43 Frequently Asked Questions (continued) How can I setup my router to work with a Cable modem connection? Power cycle the cable modem and router: S t e p 1 Turn the cable modem off (first). Turn the router off Leave them off for 2 minutes.** Turn the cable modem on (first).
  • Page 44 MTU to a lower number such as 1472, 1452, etc. Contact your ISP for more information and the proper MTU setting for your connection. Click Apply. When prompted, click Continue. Once the screen refreshes, Step 6 unplug the power to the D-Link VoIP Terminal Adapter.
  • Page 45 Turn off your DSL modem for 2-3 minutes. Turn back on. Once the modem Step 7 has established a link to your ISP, plug the power back into the D-Link VoIP Terminal Adapter. Wait about 30 seconds and log back into the router.

  • Page 46: Technical Support

    Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone.

Table of Contents