Advertisement
In planning any installation,note that the free lengthof thisappliance'spower
Step 5:
Locate the LP orifice spud packettaped tothe undersideof th_
cord, extendingbeyonda point3_" (9.53 cm) left of the nominalcenter of the
burner box. The spuds are zinc-plated and have small hum
rear wall of the burner box, when viewed from the front ofthe unit,is approxi-
bets stamped on the side. This number codes the orificediem
mately 46" (117 cm).
eter and its correct burner location. The following illustration
show correct LP orificespud location for 4 burner and 5 burne
models, respectively.
WARNING
ELECTRICALGROUNDING INSTRUCTIONS
INSTALLATION OF LP (ZINC-PLATED) ORIFICE
THIS APPLIANCE IS EQUIPPED WITH ATHREE PRONG GROUND-
ING PLUG FORYOUR PROTECTIONAGAINSTSHOCK
HAZARDAND
SPUDS
SHOULD BE PLUGGED DIRECTLY INTO A PROPERLY GROUNDED
RECEPTACLE. DO NOTCUTOR REMOVETHE GROUNDING PRONG
4 Burner
model
(30" Wide)
FROMTHIS PLUG.
Fig. 8
WARNING
THIS APPLIANCE MUST BE DISCONNECTED FROM ITS ELECTRI-
CAL SUPPLYATTHE WALL RECEPTACLE BEFORE SERVICING THE
APPLIANCE.
CONVERTING APPLIANCE FOR USE WITH LP GAS
WARNING
Propane conversion is to be performed by a JENN-AIR AUTHORIZED
SERVICER
(or other qualified agency) in accordance with the
O
manufacturer's instructions and all codes and requirements of the au-
thority having jurisdiction. Failure to follow instructionscould result in
(_
(_
seriousinjuryor propertydamage. The qualified agency performing this
work assumes responsibilityfor this conversion.
WARNING
Electrical power and gas must be turned offpriorto conversion.
is appliance was adjusted at the factory for use with natural gas. To con-
,rtit for use with LP gas (propane or butane), each of the following modifica-
,,onsmust be performed:
5 Burner
Model
(36" Wide)
A. Replace all orifice spuds
Fig. 9
Step 1:
Remove the grates and burner heads.
Step2:
With an adjustablewrench, unscrewand removethe brasscollar
nuts (Fig. 7).
Step 3:
Trim a small piece of masking tape to the size of a dime and
affix it over the end of a 9/32" nut driver.
Step 4:
Firmly press the nut driver over the orifice spud (Fig. 7) and
loosenspud byturningcounterclockwise.Carefullyliftnutdriver
out of burner throat. Orifice spud should be captured in the
recess. Repeat this step for each burner.
Fig. 7 REMOVAL OF ORIFICE SPUD
©©©
©
©
BRASS
COLLAR
NUT
"_(_iJ
%2" NUTDRWER
PIECEOF MASKING
END
Step 6:
With the masking tape et/ll in place in the recess of the rl
OF DRIVER
driver,pressan LP odfice spud (zinc-plated) intothe recess:
I
__
INDENTATION
that it is snugly captured,
BURNERBASE
Step 7:
Carefully installthe orificespud in the appropriate burnerthrc
by turning clockwise to tighten, 33ghtento a torque of 15 to
inch-lbs.
ORIFICESPUD
Step 8:
Replace cylindricalbrass collar nuts and tighten to a torque
of 6Oin.-Ibs. Replace burear heads and grates. Index each
grate to its burner pan.
Step 9:
Save the odfices removed from the appliance for future us_
5
Advertisement
