Delivery Scope; Declaration Of Conformity; Noise/Vibration Information; Mounting And Operation - Bosch PST 700 E Original Instructions Manual

OBJ_BUCH-1067-002.book Page 10 Friday, July 1, 2011 10:58 AM
10 | English
Symbol Meaning
When sawing metal, apply coolant/
lubricant alongside the cutting line
Article number (10-digit)
P Rated power input
1
n Stroke rate at no-load
0
Cutting capacity, max.
Wood
Aluminium
Metal
Particle board
Weight according to
EPTA-Procedure 01/2003
/II Symbol for protection class II
(completely insulated)
L Sound pressure level
pA
L Sound power level
wA
K Uncertainty
a Vibration total value
h

Delivery Scope

Jigsaw.
"Cut Control", splinter guard, application tools and other ac-
cessories shown or described are not part of the standard de-
livery scope.
A complete overview of accessories can be found in our ac-
cessories program.
Intended Use
The machine is intended for making separating cuts and cut-
outs in wood, plastic, metal, ceramic plates and rubber while
resting firmly on the workpiece. It is suitable for straight and
curved cuts with mitre angles to 45°. The saw blade recom-
mendations are to be observed.
Technical Data
The technical data of the machine are listed in the Table on
page 60.
The values given are valid for a nominal voltage [U] of 230 V.
For different voltages and models for specific countries,
these values can vary.
Please observe the article number on the type plate of your ma-
chine. The trade names of the individual machines may vary.
2 609 005 186 | (1.7.11)

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2004/108/EC,
2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 17.06.2011

Noise/Vibration Information

The measured values of the machine are listed in the table on
page 60.
Noise and vibrational values (vector sum of three directions)
determined according to EN 60745.
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.

Mounting and Operation

Action
Inserting the Saw Blade
Removing the Saw Blade
Adapting the position of the guide
roller
Mounting the splinter guard
Mounting and use of "Cut Control" 5
Connecting the dust extraction
Adjusting the Cutting Angle
Switching on the sawdust blower
device
Figure Page
1 61
2 61
3 61
4 62
62
6 63
7 63–64
8 64
Bosch Power Tools