Commercial Mode Setup - LG 20LH1DC1 Installation And Operating Manual

COMMERCIAL MODE SETUP

This page provides an overview of the TV configuration. See the pages listed below for more spe-
cific, detailed instructions at each step; how to access and use the Installer menu etc.
*Note1: Disconnect all Aux inputs. Under certain conditions, Auto Program (Channel
search) is disabled if there is an Aux input active.
Overview: Commercial Mode Setup Procedure
1. Set Installer Menu Items
(Enter Installer Menu, see page 51 for detailed instructions.)
a. Set Installer menu item 1 17 FACT DEFAULT, to 001 and press ENTER.
(This clears all installer menu items, custom settings, channel labels/icons
and reloads the factory default settings.)
b. Set Item 003 BAND/AFC.
- Broadcast: set to 000.
- CATV: set to 001.
c. Set item 028 CH OVERIDE to 001. This allows access to Auto Program,
Channel Labels and Channel List options in the Channel Menu.
d. Set other particular installer items that affect your TV programming
network. See pages 55 - 60.
e. After all required installer menu item settings have been adjusted, press
ENTER on the remote to remove Installer Menu.
2. Set Up TV Features
(See Picture, Sound, Setup menus etc. See TV Clonable options list on page
60.) Installer Note: Some TV features will have to be set up after running.
Auto Program. An example is Digital Font options. This feature is not
available until digital channels are found in the channel scan. Set up Digital
Font options after Auto Program finds a digital channel with digital captions.
Do this before running 2-5-5 + Menu.
3. Run Auto Program
(Search for all available channels.) Go to the Channel menu and access the
Auto Program option, follow on-screen instructions.
a. Edit Channel Scan. In the Channel Menu, access the Channel List menu.
• Delete channels per your system requirements: do you want to delete any
free channels so the guest cannot access them?
• Add familiar Channel Icons like ABC, CBS, NBC etc. to the channel
on-screen display. Add identifiable labels for the end user to readily know
what common networks are available. In the Channel menu, select the
Channel Label option, follow instructions on the bottom of the screen.
4. Transfer TV Setup to Controller Box: 2-5-5 + Menu
After the TV channel scan has been edited and channel label icons added,
enter the Installer menu. Once in the Installer menu, press 2-5-5 and
MENU on the remote. This transfers the TV setup to the internal controller
box.
*Note: Only do 2-5-5 + MENU once or TV setup may be corrupted. TV scans
available channels and exits menu when transfer to controller is complete.
5. Perform Adding Custom Channel Labels: 2-5-4 + Menu Mode
Enter Installer menu, press 2-5-4 and Menu. Add your own custom labels to
the channel on-screen displays. (See page 60.) To remove menu press
MENU.
*Note: 2-5-4 + MENU can be performed more than once.
Verify TV Setup
At this point, verify that the channel lineup, channel icons and custom labels
are correct. Make sure the TV features are set per your requirements.
Set item 028 CH OVERIDE to 000 to lock the channel scan. After the
preceding has been completed, the Master TV setup is ready to be copied to
the LT2002 Clone Programmer, see next page.
- HRC: set to 002
- IRC: set to 003
HOSPITAL_20 PTC INSTALLER MENU
000 INSTALLER SEQ
UPN 000-000-000-000
PTC V1.00.000 CPU V1.01.00
20LH1DC1 Installer Menu
117 FACT DEFAULT
003 BAND/AFC
028 CH.OVERIDE
073 CH. NOT AVBLE
20LH1DC1 Installer Menu Items
DIGITAL 19-3 ANALOG 2
MONO STEREO SAP
WXYZ
MONO
WXYZ
Custom Channel Label 'WXYZ' created in
2-5-4 + Menu Add Channel Label Mode
028 CH. OVERIDE
After TV setup has been verified,
set item 028 Ch Overide back to 000.
*Note: Default setting for Aux sources is to be active
in the installer menu. The Aux sources will appear
between the highest Analog and lowest Digital
channel number with Channel Up/Down. If the Aux
sources will not be used, it is advisable to set them
to 000 (Off) before doing 2-5-5 + Menu.
After doing 2-5-5 + Menu, the only way to turn the
Aux source off so they will not appear in the
channel scan, is to go to the Channel Bank menus
and turn each Aux source off by selecting 'Normal
Delete' .
Refer to installer items: 35, 39.
000
FPGA 20FD
00X
00X
001
001
000
51