Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Net Optics Manuals
  4. Switch
  5. iBYPASS 40G
  6. Quick install manual

Net Optics iBYPASS 40G Quick Install Manual

Net optics ibypass 40g switch
Hide thumbs

Advertisement

Quick Links

Download this manual

Quick Install Guide

I2BP-40
800-0228-001 Rev A 11/13

Advertisement

loading
Need help?

Need help?

Do you have a question about the iBYPASS 40G and is the answer not in the manual?

Questions and answers

Related Manuals for Net Optics iBYPASS 40G

Summary of Contents for Net Optics iBYPASS 40G

  • Page 1: Quick Install Guide

    Quick Install Guide I2BP-40 800-0228-001 Rev A 11/13...
  • Page 2 PLEASE READ THESE LEGAL NOTICES CAREFULLY. By using the Net Optics iBypass 40G Switch, you agree to the terms and conditions of usage set forth by Net Optics, Inc. No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics retains all intellectual property rights associated with the technology described in this manual.

  • Page 3: Table Of Contents

    Contents iBypass 40G Switch Content iBypass 40G Switch Overview Connect Power Connect PC to Console Port Configure the iBypass 40G IP Connect to the Network Connect Monitoring Tools...

  • Page 4: Ibypass 40G Switch Content

    40G Switch Content This guide provides the initial steps to set up and configure the Net Optics iBypass 40G Switch. Carefully unpack the contents and verify you have the following components: • iBypass 40G Switch • 3-meter RJ45, CAT 5e 4-pair •...

  • Page 5: Ibypass 40G Switch Overview

    40G Switch Overview Management Monitor Network Port Ports Ports 2x16 Character Display Console Activity & Alarm Bypass, Tap, Power Port LEDs LEDs Figure 1 - Front View • Console Port (RJ45) and Management Port (RJ45) • 2 x 40G Monitor Ports (uses QSFP+ transceivers ) •...
  • Page 6 Rack Mount iBypass 40G Switch Install the iBypass 40G Switch into a standard 19-inch equipment rack. The switch is designed to occupy one rack unit. Do the following to install the iBypass 40G Switch into an equipment rack: Remove the Ear Extenders and screws from the shipping bag.
  • Page 7 Short Ear Extender Long Ear Extender binds two switches for one switch Figure 3 - Use Ear Extenders in Rack Mount Preparation...

  • Page 8: Connect Power

    Plug one of the supplied power cords to a power connector located at the rear of the chassis. Plug the other end to a power source. See Figure 4. For redundancy, plug the other power cord to the iBypass 40G. Plug the other end to a source independent from the first power source.
  • Page 9 Figure 4 - Power Connections...
  • Page 10 Step 3 Connect Options You have two ways of logging in to the iBypass 40G switch. Option 1 - Connect PC to Management Port Connect a PC whose IP address is on the same subnet as the iBypass switch. The default address on the switch is: IP Address: 10.60.4.180...
  • Page 11 Go to Configure the IP section and follow the instructions to set a new IP address. For more information about using the iBypass 40G Switch CLI, enter help to display command information or see the iBypass 40G Switch User Guide for more details.

  • Page 12: Connect Pc To Console Port

    Go to Configure the IP section and follow the instructions to set a new IP address. For more information about using the iBypass 40G Switch CLI, enter help to display command information or see the iBypass 40G Switch User Guide for more details.
  • Page 13 DB9 to RJ45 console cable Computer with terminal emulation software Figure 6 - PC to Console Port...
  • Page 14 Step 4 Configure the IP The iBypass 40G switch ships with a default address. You can decide to use the default address, assign a static IPv4 or IPv6 IP address or use DHCP to assign an address. To configure the system with a static IPv4 or IPv6 address, do the following:...
  • Page 15 After setting the IP address, connect the Management port to the network, so that you can access the device remotely over SSH or launch the Web UI with the new IP address. To configure the system to use a DHCP address, do the following: At the CLI prompt, type the following to set the address mode: set network mode dhcp At the next prompt, type the following to reboot the device:...
  • Page 16 Assign IP in Web UI If you want to change the IP address through the Web UI, do the following: Open a browser on a PC connected to the iBypass switch or on the same subnet, and enter the default IP address in the URL, https://10.60.4.180. At the iBypass log in banner page, enter Username admin and Password netoptics.
  • Page 17 Figure 7 - Home Page Figure 9 - Configure IP Web Page...

  • Page 18: Connect To The Network

    Step 5 Connect to the Network The iBypass 40G Switch Network ports require 40G MTP cables. Network port A to a network switch or router Network port B to a network switch or router Figure 10 - MTP Cables to the Network Connect Network Port A to a network device with a 40G MTP cable.

  • Page 19: Connect Monitoring Tools

    Step 6 Connect Monitoring Tools Do the following to connect monitoring tools to the iBypass 40G Switch: Insert transceiver to Monitor port 1 Insert transceiver to Monitor port 2 Figure 11 - QSFP Connections to the Monitoring Tools Insert QSFP+ transceivers into Monitor port 1 and Monitor port 2.
  • Page 20 If you have questions while your product is under warranty or you are enrolled in a support plan, please contact the Net Optics Technical Assurance Center (TAC) via email at support@netoptics.com or by calling +1.408.737.7777, Monday through Friday, between the following hours in your region: •...