CAUTION : The laser used in the CD-RW/DVD-ROM drive can damage your eyes. Do not attempt to open the cover. To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. Use of controls or performance of procedures other than those specified herein may result in hazardous radiation exposure.
This product is manufactured to comply with the radio interference requirements of EEC DIRECTIVE 89/336/EEC, 93/68/EEC and 73/23/EEC. CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM. VARNING-OSYNLIG LASERSTRÄLNING NÄR DENNA DEL ÄR ÖPPNAD STRÄLEN ÄR FARLIG. CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1...
DirectCD v2.5b(s) Introduction Features • Enhanced-IDE (ATAPI) interface. • Power tray loading and ejection of disc. (The disc can also be ejected manually.) • Combination CD-R/RW and DVD-ROM Drive functions into one drive. • Supports UDF for easy writing to CD-RW discs. •...
DirectCD v2.5b(s) Introduction Important Precautions Follow these precautions when handling the drive or discs. • Please take notice that the manufacturer of this equipment does not offer any warranty against data loss due to inappropriate installation or handling, or direct or indirect damages. •...
5.25-inch half-height bay required +5V/+12V power socket required Windows 95/98/2000/ME/XP, Windows NT Workstation Ver.4.0 or later* CD-R : LG, Ricoh, Mitsubishi Chemical, Verbatim, Taiyo Yuden, Mitsui Toatsu, TDK, Kodak, or SKC discs are recommended. CD-RW : Ricoh, Mitsubishi chemical, Verbatim,...
DirectCD v2.5b(s) Introduction Location and Function of Controls 1. Headphone Jack 2. Volume Control 3. Emergency Eject Hole 4. Stop/Eject Button 5. Disc Tray 6. Drive activity indicator (Read/Write) 1. Digital Audio Output Connector 2. Analog Audio Output Connector 3. Jumper Connector This jumper determines whether the drive is configured as a master or slave.
DirectCD v2.5b(s) Installation Installing the Drive Before installing the drive, please note the following points. I You will need the following: • A screw driver of a suitable size to fit the securing screws • The manual for the computer, so you can find the mounting I Turn off all peripheral appliances of the computer and the computer itself, and disconnect their power cords from the wall sockets.
DirectCD v2.5b(s) Installation Before installation, set the jumper connector on the rear panel. The drive can be connected as the Master or Slave on an EIDE (ATAPI) interface. When several (up to four) EIDE devices are connected, each must be set in a unique way. Specific knowledge of hardware and software is necessary to install the drive.
DirectCD v2.5b(s) Installation The CD-RW/DVD-ROM drive connects to the motherboard of the host computer using an IDE interface cable. You may connect the CD-RW/DVD- ROM Drive as a Slave or Master device, depending on your computer. To install the drive as a Master, the jumper can be left as supplied from the factory.
DirectCD v2.5b(s) Installation To install the drive as a Slave, change the jumper setting on the rear panel to SL. Master drive (Booting hard disk) Primary connector Connect the power cable from the computer’s power supply to the socket on the drive unit, fitting the connector firmly into the power in connector. If there is no spare power cable available in the computer, you will have to purchase a splitter cable of a suitable type.
DirectCD v2.5b(s) Installation Connect the 40-pin IDE cable to the back of the CD-RW/DVD-ROM Drive, making sure the coloured (red) stripe on the IDE cable is connected to pin 1 on the CD-RW/DVD-ROM drive. Pin 1 is closest to the Power Connector. NOTE : Generally, the IDE connector is keyed and will only fit one way.
DirectCD v2.5b(s) Installation Device Drivers When using Windows 95/98/2000/Me/XP or Window NT Workstation Ver.4.0, no special device driver is required. Your system, upon Power On and bootup after installing and connecting the new CD-RW/DVD-ROM drive, will recognize and load native software drivers automatically.
DirectCD v2.5b(s) Operation How to Use the Discs When using CD-ROM discs, CD-R discs, DVD discs or CD-RW discs, don’t attach any stickers or labels to the discs. Using discs with them attached not only causes read and write errors, but data on the disc may be lost due to damage to the disc itself.
DirectCD v2.5b(s) Appendix Troubleshooting Before calling for service, check this list. • The drive doesn’t have power. • Is the power supply cable from the host computer plugged in? • Is the Power Connector to the drive securely attached? • The system doesn’t start.
Specifications Items General Supported Discs *Read Function *Write Function Disc Diameter Host Interface Read/Write Speed Mounting direction Performance Data transfer rate *Sustained *Burst(ATAPI) Average Access Time (Random) Buffer capacity MTBF Audio Output Line Output Level Headphone Environmental When operating Conditions When not operating Dimensions Dimensions &...
550 MATHESON Blvd. East Mississauga. Ontario L4Z4G3 CANADA LG Electronics Deutschland GMBH Jakob-Kaiser-Straße 12, D-47877 Willich, Germany LG Electronics U. K. Ltd. LG House, 264 Bath Road, Slough Berkshire SL1 4DT United Kingdom Goldstar France S.A.R.L Paris Nord II 22, Avenue des Nations-B.P.50372 VILLEPINTE...