Related Manuals for Laundrylux WHWF09810M
Summary of Contents for Laundrylux WHWF09810M
- Page 1 CROSSOVER SERIES In a class by itself MODEL N O. WHWF09810M/NM MODEL N O. E HWF09810M/NM 7 W A S H E R I N S T A L L A T I O N M A N U A L 3 Laundrylux DOC.
- Page 2 ATTENTION INSTALLER For coin-operated models, the coin meter housing is packed UNDER Fig. the machine. DO NOT DISCARD THE PACKING MATERIALS without first removing the meter housing! See installation instructions later in this manual for details. Coin meter housing ATTENTION INSTALLER Four transportation bolts are installed in the rear of the machine, to protect the suspension and tub assembly from damage during shipment.
- Page 3 Installation manual WHWF09810M/NM EHWF09810M/NM WARNING: ALL OPERATING AND MAINTENANCE PROCEDURES SHOWN ON THE NEXT PAGE OF THIS MANUAL MUST BE FOLLOWED DAILY FOR PROPER OPERATION OF YOUR MACHINE. PLEASE ENTER THE FOLLOWING INFORMATION AS IT APPEARS ON THE MACHINE(S) DATA PLATE(S).
- Page 4 Intentionally blank...
- Page 5 SAFETY AND WARNINGS SIGNS Replace If Missing Or Illegible One or more of these signs must be affixed on each machine as indica- ted, when not included as part of the front instruction panel. LOCATED ON THE FRONT OF THE DETERGENT DISPENSER:...
- Page 6 Ne pas réparer ou remplacer les pièces de l’appareil ou procéder à l’entretien de celui-ci sauf si les instructions visant l’entretien et les réparations qui doivent être effectués par l’utilisateur le spécifient, si vous comprenez bien ces instructi si vous possédez les connaissances nécessaires. MANUFACTURED BY HAIER EXCLUSIVELY FOR LAUNDRYLUX...
- Page 7 Follow all maintenance and safety procedures. Further information regarding machine safety, service and parts can be obtained from your dealer or from Laundrylux through its Teletech Service Hotline - 516/371- 0700. All requests for assistance must include the model, serial number and electrical characteristics as they appear on the machine identification plate.
-
Page 8: Location Requirements
NOTICE TO INSTALLER Improper installation of this machine: • May cause serious damage to the machine. • May result in other property damage. • May cause personal injury. • Will void the manufacturer's warranty. Location Requirements • The location for your washer should have a flat and even floor. This will improve performance, minimize noise and decrease washer movement. -
Page 9: Safety Instructions
Contents Contents Technical data................... 1:1 Installation ....................2:1 Water connections ................3:1 Drain connection .................. 4:1 Connection of external liquid supplies ..........5:1 Function checks ..................6:1 Preventive maintenance ................7:1 The manufacturer reserves the right to make changes to design, material and/or specifications without notice. - Page 10 Intentionally blank...
-
Page 11: Technical Data
Technical data Technical data WHWF09810M/NM EHWF09810M/NM Innerdrum volume litres/ft 98/3.5 diameter mm/inch 554/21 4/5 Drum speed wash extraction 1000 G-factor Weight, net kg/lbs 136/300 WHWF09810M/NM Connections EHWF09810M/NM Water valves DN20 connection 3/4" Rec. water pressure 30-90 200-600 Functioning limits 8-145... - Page 12 Technical data 1 Power line 2 Air Vent for Safety 3 Hot water 4 Cold water 5 Drain 6 Coin meter (coin operated models only) 7 Control panel 8 Detergent dispenser 9 Door 1 2 3 A 1109mm = 43 5/8 inch NOTES : B 1010mm = 39 3/4 inch C 592mm = 23 3/8 inch...
-
Page 13: Installation
Installation Installation For safety,two people should install this product. Leave the machine on the transport pallet until it can be placed in the final, prepared position. First remove all the packing materials. Upon opening of the package, water drops may be seen on the plastic bag and the drum. - Page 14 Installation Transportation Bolts The washer is fitted with transportation bolts to prevent internal damage during transportation. Transportation bolts must be removed before using the washer. Removing Transportation Bolts 1. Unscrew the 4 bolts with a wrench. Remove the lower 2 bolts first, then the upper two. Fig.
- Page 15 Installation Siting Install the machine close to a drain standpipe or floor drain,and within 4 feet of the water supply Water supply spigots. In order to make installation and servicing Drain standpipe the machine easier the following clearances are recommended: •...
- Page 16 Intentionally blank...
-
Page 17: Water Connections
Installation Water connections All inlet connections to the machine are to be fitted with manual shut-off valves and filters, to facilitate installation and servicing. NOTE: The inlet filter screens are provided inside the machine's connection fittings. Water pipes and hoses should be flushed clean before installation. After installation, hoses should hang in gentle arcs. - Page 18 Installation Water type Water connection Fig. cold and hot cold...
-
Page 19: Drain Connection
Installation Drain connection Connect the machine’s drain hose to the back of the washer, using the spring clamp provided in the accessories package. Avoid sharp bends in the hose which may prevent proper draining. You can connect the drain hose to a sewer stand pipe. If you do this, make sure Fig. - Page 20 Intentionally blank...
- Page 21 Installation Electrical installation must be carried out All optional equipment connected must be by licensed, qualified personnel! EMC-approved to EN 50081-1 or EN 50082- Connection of external price reduction control signal The accessories package includes a two-wire Fig. harness for price reduction (promotion) activation.
-
Page 22: Electrical Connections
Installation 5: 2 Electrical Connections This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounded plug. -
Page 23: Function Checks
Function checks Function checks Perform the following checks once the machine is installed: • Open the water supply valves. • Press the START button or, if needed, insert coins and press START. Check: • that the drum rotates normally and that there are no unusual noises. •... - Page 24 Intentionally blank...
-
Page 25: Preventive Maintenance
- Check that there are no signs of leakage on the floor beneath the machine. Locate and repair any leak. Contact your local dealer, or Laundrylux Technical Support at 516-371-0700 if you have questions regarding installation, operation, or maintenance of your machine. - Page 26 Installation OPL MODE SETUP To convert the machine for OPL operation, the front control / display module must be reset to “coin mode” and the prices of all six cycles and options must be set to $0.00. Fig 1 Reset Control / Display Module Method A 1.
- Page 27 4. Press four program buttons, COLD, WARM, HOT, & DELICATE to set price to 0.00 Each button increments a corresponding digit, left to right, in the price. Each digit rolls over from 9 to 0 without affecting other digits. The left-most digit cannot be programmed to “0”, but can be blanked out.
- Page 29 If your business is in need of laundry expansion large or small, Laundrylux Financial Services is ready to help you get there. Leasing and financing is available at the most competitive rates on all Wascomat products.