Page 3
Installation Manual WMTW4371M WMTW4371M** Note: “**” = C (Color), 2,3,4... (Color variant). E.g. WMTW4371MC2 =”Ore Silver” WARNING: ALL OPERATING AND MAINTENANCE PROCEDURES SHOWN IN THIS MANUAL MUST BE FOLLOWED AT THE FREQUENCY SPECIFIED FOR PROPER OPERATION OF YOUR MACHINE. PLEASE ENTER THE FOLLOWING INFORMATION AS IT APPEARS ON THE MACHINE(S) DATA PLATE(S).
Page 5
IMPORTANT SAFETY INSTRUCTIONS IMPORTANTES MESURES DE SECURITE WARNING - AVERTISSEMENT - Pour réduire les risques d´incendie, de choc électrique ou de blessure quand, I´appareil est utilisé: 1. Read all instructions before using the appliance. Lire toutes les instructions avant d’utiliser l’appareil. 2.
Page 6
Missing or illegible ones must be replaced immediately. Be sure you have spare signs and labels available at all times. These can be obtained from your distributor or from Laundrylux. 2. Check the door safety interlock, as follows: (a) RAISE THE LID of the machine and attempt to start in the normal manner: For coin-operated models, insert the proper coins to start the machine.
Page 7
NOTICE TO INSTALLER Improper installation of this machine: • May cause serious damage to the machine. • May result in other property damage. • May cause personal injury. • Will void the manufacturer’s warranty. Location Requirements • performance, minimize noise and decrease washer movement. •...
Page 8
Contents Technical Data ....................1:1 Installation ......................2:1 Water Connections ..................3:1 Drain Connection ..................4:1 Connection of External Liquid Supplies ............5:1 Function Checks ....................6:1 Preventive Maintenance ...................7:1 The manufacturer reserves the right to make changes to design, material Safety Instructions •...
Page 9
Technical Data Technical Data WMTW4371M WMTW4371M** Innerdrum volume litres/ft 82/2.9 diameter mm/inch 505 /19 7/8 Drum speed wash extraction max rpm G-factor Weight, net kg/lbs 62/137 WMTW4371M Connections WMTW4371M** Water valves DN20 connection 3/4" Garden Hose via included hoses Rec. water pressure 15-90 100-620 Functioning limits...
Page 10
Technical Data Control Panel Coin Meter (coin operated models only) Hot Water Cold Water Cable Entry for Optional External Harness Drain NOTES: A 1126 mm = 44 21/64inch B 686 mm = 27 inch C 686mm = 27 inch D 1345 mm = 52 61/64 inch...
Page 11
Installation Installation For safety, two people should install this product. First remove all the packing materials. Upon opening of the package, water drops may be seen on the plastic bag and the drum. This is a normal phenomenon resulting from water tests in the factory.
Page 12
Installation Install the Coin Meter (coin operated models) Fig. 2 Remove the coin meter housing cover (c) Install the front plate the coin meter and fasten it (b) Fig. Install the cover of the coin meter housing (a) Plug the coin meter(s) into the COIN 1 (Red) and COIN 2 (White) harness plugs.
Page 13
Installation Siting Install the machine close to a drain standpipe or Water supply spigots. In order to make installation and servicing Drain standpipe the machine easier the following clearances are recommended: • At least 20 inches (500 mm) between the Fig.
Page 14
Installation Water Connections All inlet connections to the machine are to be fitted with manual shut-off valves and filters, to facilitate installation and servicing. NOTE: The inlet filter screens are provided inside the machine’s connection fittings. Water pipes and hoses should be flushed clean before installation. After installation, hoses should hang in gentle arcs.
Page 15
Installation Water Type Water Connection Fig. Cold and Cold...
Page 16
Installation Drain Connection Connect the machine’s drain hose to the back of the washer, using the spring clamp provided in the accessories package. Avoid sharp bends in the hose which may prevent proper draining. Fig. • You can connect the drain hose to a sewer stand pipe. If you do this, make sure that the outlet hose will not come out of the stand pipe.
Page 18
Installation Electrical Connections This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounded plug. The plug must be inserted into an outlet that is properly installed and grounded.
Page 19
Function Checks Function Checks Perform the following checks once the machine is installed: • Open the water supply valves. • Press the START button or, if needed, insert coins and press START. Check: • that the drum rotates normally and that there are no unusual noises. •...
Page 20
- Inspect the drive belt. Adjust the tension or replace as necessary. and repair any leak. Contact your local dealer, or Laundrylux Technical Support at (516) 371-0700 if you have questions regarding installation, operation, or maintenance of your machine.
Need help?
Do you have a question about the ENCORE WMTW4371M Series and is the answer not in the manual?
Questions and answers
how do i program the price in the coin acceptor