Bona HD Belt Owner's Operation Manual

Bona belt hd
Hide thumbs Also See for HD Belt:

Advertisement

Quick Links

Bona Belt HD
by
Owner & Operation Manual
Manual is compatible with Kunzle & Tasin Taurus
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HD Belt and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Bona HD Belt

  • Page 1 Bona Belt HD Owner & Operation Manual Manual is compatible with Kunzle & Tasin Taurus...
  • Page 2 BELT HD TAURUS User Manual_January 2014 Edition Foreword This manual contains important information on the safe use and operation of this machine. Failure to read this manual before operating, adjusting or servicing this machine could cause injury or damage to persons or objects. Anybody operating the machine should understand how to use and operate it before starting it up.
  • Page 3: Table Of Contents

    BELT HD TAURUS User Manual_January 2014 Edition Contents Key for machine symbols Operator safety instructions Storage Transporting and handling the machine Transport with one person Transport with two people Introduction Information on safe use Correct use Machine data plate Commencing operation Instructions for assembly following transportation Instructions for electrical connection Cables, extensions and plugs...
  • Page 4: Key For Machine Symbols

    BELT HD TAURUS User Manual_January 2014 Edition Key for machine symbols READ THE INSTRUCTIONS CONTAINED IN THIS USER AND MAINTENANCE MANUAL BEFORE USING THE MACHINE HEARING PROTECTION DURING USE IS RECOMMENDED PROTECTION OF THE AIRWAYS DURING USE IS RECOMMENDED HAZARD DUE TO ELECTRICITY HAZARD DUE TO MOVING PARTS Operator safety instructions Failure to comply with HAZARD notices on the machine or in this...
  • Page 5: Storage

    BELT HD TAURUS User Manual_January 2014 Edition Storage It is advisable to store the machine in its original packaging. Doing so makes it possible to form a column of two packages maximum, with one on top of the other. If the machine is removed from the original packaging and is not used for some time ensure the wheels and drum are not in contact with the ground.
  • Page 6 BELT HD TAURUS User Manual_January 2014 Edition Transporting and handling the machine Transport with one person 3. Loosen the belt tightener using the lever pos. 2 fig. A and remove the belts. 5. Remove the motor and take it to the work 4.
  • Page 7: Transport With Two People

    BELT HD TAURUS User Manual_January 2014 Edition Transporting and handling the machine Transport with one person 7. Loosen the handle (pos. 9 fig. A) and 8. Lift the base frame by clasping the front and back. Bring the remove the tube from its housing and bring belt guard to the edge and take it to the work area.
  • Page 8: Introduction

    Introduction Information on safe use This instruction manual should be read carefully before using the BELT HD TAURUS wood flooring sander for the first time. The instruction manual contains important information on safety and preventing improper use of the machine and will resolve any doubts or questions, making it possible to operate the machine safely and with ease.
  • Page 9: Commencing Operation

    BELT HD TAURUS User Manual_January 2014 Edition Commencing operation Instructions for assembly following transportation To re-assemble the machine following transportation proceed as follows: 1. Open the belt guard. 2. Position the motor in Secure the motor by tightening its housing. the knob (pos.
  • Page 10: Instructions For Electrical Connection

    BELT HD TAURUS User Manual_January 2014 Edition Commencing operation Instructions for assembly following transportation 6. Pull the belt tightener as shown: 7. Fit the suction pipe and drum control rod. 8. Lift the drum with the lever (pos. 4 fig. A). 9.
  • Page 11: Cables, Extensions And Plugs

    BELT HD TAURUS User Manual_January 2014 Edition Commencing operation Cables, extensions and plugs Only use approved cables. The maximum recommended cable length is 7m; for greater lengths use cables with a larger cross-section. CAUTION Using the machine with unsuitable cable cross-sections and/or excessively long cables may cause injury or damage to people or objects.
  • Page 12: Recommendations On Prevention Measures For Users

    BELT HD TAURUS User Manual_January 2014 Edition Recommendations on prevention measures for users Personal safety measures WARNING Sawdust can spread through the air and be inhaled when using the sander. Always wear a dust mask when using the sanding equipment. WARNING The eyes and/or body may suffer injury if personal safety clothing is not used.
  • Page 13: Instructions On Correct Machine Use

    BELT HD TAURUS User Manual_January 2014 Edition Recommendations on prevention measures for users Compliance with safety measures and warnings HAZARD The use of this machine with a damaged power supply cable may cause electric shock. Check the power supply cable regularly for damage such as splitting or wear and tear. Do not use the machine if the power supply cable is damaged.
  • Page 14 BELT HD TAURUS User Manual_January 2014 Edition Instructions on correct machine use 11. Always keep the work area well-lit. 12. The use of accessories other than those recommended in this manual may cause injury. 13. The sander is for indoor use only.
  • Page 15: Machine Specifications

    BELT HD TAURUS User Manual_January 2014 Edition Machine specifications 750 x 203 mm Abrasive belt dimensions 200 mm Drum width 185 mm Drum diameter Drum speed 1800-2050 revs/min 50 Hz 2000-2200 revs/min 60 Hz Motor 230V  50 Hz 2.99 kW (A04) EUROPE 380V ...
  • Page 16: Machine Warnings

    BELT HD TAURUS User Manual_January 2014 Edition Machine warnings Prohibited use WARNING This equipment is not to be used by anyone (children included) with physical or mental disabilities, or anyone without the relevant experience and knowledge, unless they have received instructions on using the equipment and are supervised by a responsible person to ensure their safety.
  • Page 17 BELT HD TAURUS User Manual_January 2014 Edition Starting the machine 5. Open the side guard (fig. C. 6. Lower the tensioning unit using the drum tensioning lever. 7. Insert the abrasive belt letting it protrude by approximately 2 WARNING Only use 750x203 mm abrasive belts. ension the unit using the drumtensioning lever.
  • Page 18 BELT HD TAURUS User Manual_January 2014 Edition Starting the machine Connect the plug to the socket. 10. Ensure the lever is lowered (pos. 1 fig. A) and the drum is raised off the floor. 11. Starting up: a) SINGLE PHASE MOTOR 1- Turn the lever on the switch pos.
  • Page 19 BELT HD TAURUS User Manual_January 2014 Edition Starting the machine WARNING Check carefully that the drum rotation direction is the same as indicated on the belt cover. If not switch off the machine (STOP button) and turn the reversing switch lever from position 1 to position 2. Press the START button.
  • Page 20: Machine Adjustment Procedures

    BELT HD TAURUS User Manual_January 2014 Edition Starting the machine 15. To stop the machine: a) SINGLE PHASE MOTOR b) THREE PHASE MOTOR Turn the lever of the switch from position 1 to button. Press the STOP position 0. IMPORTANT If starting the machine is difficult in winter when temperatures are very low remove the abrasive belt and start the motor, letting it idle for several minutes.
  • Page 21: Adjusting Sanding Pressure

    BELT HD TAURUS User Manual_January 2014 Edition Machine adjustment procedures Procedures for centring the abrasive belt When first fitted the belt may be in the wrong position. In this case use the spanner as shown (pos. 13 fig. D proceed as follows: Turning screws 2.
  • Page 22: Wall Edge Castor

    BELT HD TAURUS User Manual_January 2014 Edition Machine adjustment procedures Wall edge castor A support with a free castor has been fitted to avoid damage to the skirting board or wall when sanding along the wall. WARNING The wall edge castor is correctly positioned when the machine is approximately 8 mm away from the wall with the castor up against Before starting work position the castor correctly by unscrewing the...
  • Page 23: Routine Maintenance To Be Performed

    BELT HD TAURUS User Manual_January 2014 Edition Machine adjustment procedures Wheel adjustment (on a surface parallel to the axis of the drum) To adjust proceed as follows: Turn the machine over. With the tool provided with the machine check how much the fixed wheel protrudes. Loosen the nut pos.
  • Page 24: Drums (For The User)

    BELT HD TAURUS User Manual_January 2014 Edition Routine maintenance to be performed Drums (for the user) Check the outer surface of the drum regularly. Remove any dirt. Wheels (for the user) Remove dirt from the machine unit and wheels regularly. Dirt may cause uneven sanding.
  • Page 25: Belt Tension (For The User)

    BELT HD TAURUS User Manual_January 2014 Edition Routine maintenance to be performed Dust bag (for the user) As an alternative to the fabric bag the following may be used: a) Disposable paper bags, available in packs of 3 b) Remote control industrial vacuum cleaner with tube (P/N 6300030142).
  • Page 26: Drum Pulleys And Suction Fan Pulleys (For The User)

    BELT HD TAURUS User Manual_January 2014 Edition Routine maintenance to be performed Drum pulleys and motor pulleys (for the user) Regularly check that the groove (2) of the pulley has not sunk otherwise the belt (1) will operate on the bottom (3) of the pulley itself.
  • Page 27: Emergency Situations (For The User)

    BELT HD TAURUS User Manual_January 2014 Edition Emergency situations (for the user) FAULTS CAUSES SOLUTIONS Insufficient cutting Unsuitable or worn abrasive Replace the abrasive Insufficient drum pressure Increase drum pressure Insufficient belt tension Increase belt tension Worn belt Replace the belt Insufficient motor speed Insufficient tension due to: Excessive cable length or unsuitable...
  • Page 28: Declaration Of Conformity

    BELT HD TAURUS User Manual_January 2014 Edition DECLARATION OF CONFORMITY DECLARATION OF CONFORMITY 2006/95 EC, 2006/42 EC 2004/108 EC, 2002/95 EC 2002/96 EC KUNZLE & TASIN S.r.l. Manufacturer and entity authorised to compile and maintain the technical file Registered headquarters Business Management and Production Site Via Circonvallazione Est.
  • Page 29: Disposal

    BELT HD TAURUS User Manual_January 2014 Edition Disposal Smaltimento di apparecchiature da rottamare da parte di privati nell’Unione Europea. Questo simbolo che appare sul prodotto o sulla confezione indica che il prodotto non deve essere smaltito assieme ad altri rifiuti domestici.
  • Page 30: Diagrams

    BELT HD TAURUS User Manual_January 2014 Edition Diagrams...
  • Page 31 BELT HD TAURUS User Manual_January 2014 Edition Diagrams...
  • Page 32 January 2014 Edition...

Table of Contents