Advertisement
Your
Changing the batteries
REFLEX DP
1
Low Battery indicator
1.
2
Your hearing system may be
1.
Open the battery
programmed to inform you when the
battery should be replaced for best
compartment.
3
system performance. You may hear an
4
intermittent series of beeps and/or
8
experience low amplification power or
5
volume/ change the battery when
6
2.
either of thes occurs.
7
2.
Remove coloured
Features
sticker from new
battery, place battery
1. Earhook
in drawer with +
2. Mircophone opening
symbol on battery +
3. Volume control
side up. (You should
4. Cover for programming socket
only remove the
3.
5. Program button
protective sticker if
6. Battery compartment
you actually use the
7. udio input
battery).
8. Colour-coded typeplate
red = right instrument
blue - left instrument
3.
Close battery door.
Switching the
instrument on/off
On:
Using the push button
Power-on delay
Close the battery compartment fully
Your REFLEX DP can
Your hearing instrument may be
to switch on.
also be programmed
equipped with a "power-on delay"
by your NHS
feature.
Audiologist to be
This feature delays sound from entering
turned on and off
your hearing instrument when it is first
using the program
turned on, so that you may insert the
button.
heaing instrument into your ear
To turn your hearing instrument off,
without experiencing unpleasant
press and hold the program button for
feedback (whistling).
approximately 3 seconds. To turn your
Check with your NHS Audiologist
Off:
hearing instrument on again, press
about which on/off function your
and hold the program button for
Press open the battery compartment
REFLEX DP is equipped with.
to the first stop to switch off.
approximately 3 seconds. Please note
that when you turn your hearing
instrument off using the program
button, you must wait approximately
10 seconds for the instrument to reset
before turning it back on using the
program button.
Selecting the
hearing program
Using the volume control
tick box
The REFLEX DP can be programmed
Your REFLEX DP
with up to 3 hearing programs which
hearing system is
are selected with a program button.
fully automatic.
Each time the button is pressed the
There is no need to
instrument changes to the next
manually adjust the
program, which is confirmed with beep
volume control.
tones. The number of beep tones is the
However, if you
Rotate the wheel
same as the selected program.
upwards to increase
prefer manual
volume. Rotate it
volume control, your
down to decrease
Your audiologist will complete
REFLEX DP hearing
volume.
your program details below:
system can be
programmed for
Hearing program
manual adjustment.
This will be done by
1.
Everyday listening
your NHS audiologist.
2................................
3................................
REFLEX DP will always be on
program 1 when initially switched on.
Fitting the audio shoe to
the hearing instrument
It is possible to connect
Attaching the audio shoe
accessories through an
If your system is programmed for
audio shoe.
manual adjustment, the wheel-shaped
volume control can be rotated up
Ask your hearing instrument specialist.
(louder) or down (softer) to select the
desired listening volume.
Fitting
To increase volume, place your index
finger gently against the volume
Before the audio shoe can be connected
control wheel and rotate it upward. If
to the hearing system the following
your system is equipped with a
steps have to be fulfilled:
warning tone for volume control
1.
Open the battery compartment
limits, once it is heard, adjusting the
Removing the audio shoe
volume control further in that
2.
Open the audio shoe cover
direction will have no effect. To
3.
Close the Battery compartment
reduce the volume, rotate the wheel
in the opposite direction.
If your hearing system has not been
programmed for manual control
adjustment, the volume will
automatically adjust and rotating
the volume control wheel will have
no effect.
Take the audio shoe
With the connected audio shoe the
and hook the two nibs
battery compartmrnt switch is disabled
into the small recesses
and the hearing system only can be
of the hearing system
switched off with the push button.
housing. Slide the
Safety instructions for hearing
audio shoe to the
systems with audio input.
inner side of the
The audio input may be connected to
hearing system
line-operated equipment only if the
housing until it snaps
equipment fulfils the safety
into the end position.
requirement IEC 65 / DIN VDE 0860.
To remove the audio
shoe, slide the audio
shoe in the opposite
direction.
Advertisement
