Kenwood TK-2207 Service Manual page 6

TK-2207
8. If the cloning fails, no data will be available in the Slave unit
when it is returned to User mode.
9. When the cloning is successful, the Slave unit's "Scan" and
"Key lock" functions will return to their default values (Scan
= OFF, Key lock = OFF).
Notes:
• The dealer can clone data to two or more transceivers by
repeating the above procedures.
• If the transceivers Clone Mode is configured as "Disabled",
the transceiver cannot enter Clone mode.
• The table shown below will cover the frequency tables used
for wireless cloning.
• Clone mode cannot be entered in battery low state.
• A unit cannot be a "Master Unit" if it is unprogrammed. If
[PTT] is pressed, an "error" tone will sound.
• The language used in cloning depends on the "Model type"
setting, not the FPU setting. C, C2, C5 and C6 type
TK-3207 transceivers will use Chinese. Other types English.
• Once a unit is set to be the Master, it cannot be a slave
after the data has been transmitted. This protects the data
in the Master unit.
• Electronic interface may cause a failure in data transfer
during Wireless Clone, such as when waveforms or
electromagnetics are being performed at the workbench.
• Clone mode can be used ONLY by the authorized service
personnel.
• The Clone mode setting must be configured as "Disable"
before being delivered to the end-user.
• To clone, replace the antenna from both the master
transceiver and the slave transceiver with a dummy
load.
• The transmit output power is automatically set to Low
in Clone mode.
Clone Frequency Table
Operating Frequency
Clone (MHz)
Frequency Table
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
6
REALIGNMENT /
136~174
136.000
138.000
140.000
142.000
144.000
146.000
148.000
150.000
152.000
154.000
156.000
158.000
160.000
162.000
164.000
166.000
168.000
170.000
172.000
174.000
模式组合
注释：
• 经销商可以反复上述过程复制数据到 2 个或更多的手持机。
• 如果手持机复制模式被设置为 "无效" ， 则手持机不能进入复
制模式。
• 下表包含了无线复制用的频率表。
• 当电池处于低电压状态时不能进入复制模式。
• 如果手持机是非编程的它将不能成为主机。 如果按[PTT]， 将
发出一个 " 错误 " 音。
• 复制时所用的语言是根据 " 样机类别 " 设置，而不是 FPU 设
置，TK-3207 的 C，C2，C5 和 C6 类别的手持机用中文，其它
类别用英文。
• 手持机一旦被设置为主机，数据传送以后，它就不能成为子
机。这是为了保护主机里的数据。
• 在无线复制的数据传输过程中， 例如在工作台产生的电波或
电磁干扰有可能引起传输失败。
• 复制模式可以仅被批准的服务人员使用。
• 在交付给最终用户之前，复制模式设置必须被设置为"无
效" 。
• 为了复制，将模拟负载代替主手持机和子手持机的天线。
• 在复制模式，发射功率自动设定为低。
复制频率表
操作频率
(MHz)
复制频率表
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
136~174
136.000
138.000
140.000
142.000
144.000
146.000
148.000
150.000
152.000
154.000
156.000
158.000
160.000
162.000
164.000
166.000
168.000
170.000
172.000
174.000