Care And Operation - Lennox L30 BF-2 Installation And Operation Manual

CARE AND OPERATION

FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instruc-
tions exactly, a fire or explosion may result
causing property damage, personal injury or
loss of life.
A. This appliance has a pilot which must be lit.
When lighting the pilot, follow these instructions
exactly.
B. BEFORE LIGHTING smell all around the appli-
ance area for gas. Be sure to smell next to the
floor because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electric switch; do not use
any phone in your building.
Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's in-
structions.
If you cannot reach your gas supplier, call the
fire department.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, don't try to repair it, call a
qualified service technician. Force or attempted
repair may result in a fire or explosion.
D. Do not use this appliance if any part has been un-
der water. Immediately call a qualified service
technician to inspect the appliance and to replace
any part of the control system and any gas control
which has been under water.
Gas Control Valve
Pilot Assembly
LIGHTING AND SHUTDOWN INSTRUCTIONS
1. STOP! Read the safety information on this page or on label
(on appliance).
2. Turn off all electrical power to the appliance (unplug blower
power cord). Make sure the burner ON/OFF switch is in the
OFF position.
3. To gain access to the gas controls, swing the control access
door open. The control access door is located directly under
the window.
4. Push in gas control knob slightly and turn clockwise
"OFF."
NOTE: Knob cannot be turned from "PILOT" to "OFF" un-
less knob is pushed in slightly. Do not force.
5.Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low "B" in the safety information above on this label. If you
don't smell gas, go to the next step.
6.Visually locate the pilot located in the center of the firebox
beneath the rear ceramic log.
7.Turn knob on gas control counterclockwise
8.This appliance contains a spark ignition system (piezo ig-
niter), which is used to light the pilot. Push in the gas control
knob all the way and hold it in. Immediately press the button
on the piezo igniter located to the left of the gas control knob.
The spark produced by the piezo igniter should light the pilot.
Continue to hold the control knob in for about one (1) minute
after the pilot is lit. Release the gas control knob and it will
pop back up. Pilot should remain lit.
If it goes out, repeat steps 4 through 8.
If the knob does not pop up when released, stop and im-
mediately call your service technician or gas supplier.
If the pilot will not stay lit after 3 or 4 tries, turn the gas con-
trol knob to "OFF" and call your service technician or gas
supplier.
9. Turn gas control counterclockwise
switch, located either on the control panel or the exterior
side panel, to operate main burner. Adjust variable pres-
sure dial (RB Regulator / Flame Height Control) to set
burner flame to desired heat output.
10. Swing the control access door closed.
11. Turn on electrical power to the appliance (plug in blower
power cord. See page 13, Circulation Blower Operation.)
TO TURN OFF GAS TO THE APPLIANCE
1. Turn off all electric power to the appliance if service is to be
performed.
2. To gain access to the gas controls, swing the control ac-
cess door open. The control access door is located directly
under the window.
3. Push in gas control knob slightly and turn clockwise
"OFF."
NOTE: Knob cannot be turned from "PILOT" to "OFF" un-
less knob is pushed in slightly. Do not force.
4. Swing the control access door closed.
PAGE 12
2 2 2 2
to
3 3 3 3
to "PILOT."
3 3 3 3
to "ON." Use rocker
2 2 2 2
to