SIZZIX eclips2 User Manual
Sizzix eclips2 diy electronic cutter
Hide thumbs
Also See for eclips2:
- User manual (32 pages) ,
- User manual (32 pages) ,
- User manual (32 pages)
Related Manuals for SIZZIX eclips2
Summary of Contents for SIZZIX eclips2
- Page 1 ™ by Sizzix™ DIY Electronic Cutter USER’S GUIDE ™ DIY Electronic Cutter by Sizzix™ ™ DIY Electronic Cutter SUBSECTION eCAL lite Software Access Code included! Read Guide Before Operating Product. Save Guide For Reference.
-
Page 2: Important Safety Instructions
SAVE THESE INSTRUCTIONS AND WARNINGS and keep them near your eclips 2 DIY Electronic Cutter. ® Please visit sizzix.com for more information. NOTICE The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 3 * If your software doesn’t activate or if you’re not connected to the Internet, you can manually activate eCAL lite from the Help menu or go to www.craftedge.com. **12" x 24" Cutting Mat also available (sold separately). Visit sizzix.com to see a complete selection of available accessories.
- Page 4 Right Side of Machine Computer USB Port Plug Power Cord into Universal Power Supply. Plug Universal Power Supply into back of eclips2 Machine. Plug USB cable into back of eclips2 Machine. Plug flat end of USB cable into USB port of computer.
-
Page 5: Cutting Blade Maintenance
SET UP INSERTING THE BLADE INTO THE BLADE HOLDER CUTTING BLADE MAINTENANCE CAUTION: CUTTING HAZARD Blade is sharp, handle with care. Non-Cutting Side Safety Cap Angled Cutting Edge Insert this end into Blade Holder Carefully remove Safety Cap from Carefully insert Non-Cutting Side Note that Blade is exposed, but Blade, exposing Angled Cutting of Blade into hole at bottom of... -
Page 6: Starting The Machine
Leave 12 to 24 inches of clear space behind your eclips2 Machine to allow full Cutting Mat movement. Place your eclips2 Machine at least 12 inches from the edge of your work surface to prevent it from tipping over and causing possible injury. -
Page 7: Replacing The Cutting Blade
Blade, remove it from the Blade Holder and clean it with Isopropyl Alcohol (rubbing alcohol) poured onto a clean paper towel. Remove any material left inside the Cutting Blade Holder, using a Die Pick from the Tool Kit (sold separately). Visit sizzix.com to see a complete selection of available accessories. ADJUSTING THE CUTTING BLADE DEPTH CAUTION: CUTTING HAZARD Blade is sharp, handle with care. -
Page 8: Troubleshooting
Problem: Cutout cannot be removed from Cutting Mat ��������� • Use the eclips Spatula (sold separately)* when removing cutouts from the Cutting Mat. *For a complete selection of available accessories and replacement Cutting Mats, visit sizzix.com. For latest updates to the User's Guide, please visit sizzix.com. -
Page 9: End User License Agreement
ECLIPS®2 DIY ELECTRONIC CUTTER BY SIZZIX™ property rights, subject only to the limited rights granted to you in this Agreement. No right to use Sizzix, eclips2 or Ellison Educational Equipment, Inc., doing business as any other brand of Ellison Educational Equipment is granted Sizzix (“Sizzix”) is willing to grant to you a license to use... - Page 10 Following a determination by provided “AS IS”. Please refer to the End User License Sizzix that a fault covered by this Limited Warranty may have Agreement included with the Product for your rights occurred, Sizzix will: (a) ship you replacement parts or (b) and obligations with respect to the software.
- Page 12 Font: Humanist Pantone P 10 (CMYK by Sizzix™ ™ DIY Electronic Cutter by Sizzix™ ©2013 Ellison Educational Equipment, Inc. All rights reserved. 25862 Commercentre Drive, Lake Forest, CA 92630 • 877-355-4766 ™...
Need help?
Do you have a question about the eclips2 and is the answer not in the manual?
Questions and answers