Advertisement
into place. Keep smoke alarm parallel to the mounting plate so upper
and lower tabs on the plate seat into the smoke alarm (Figure 13).
CAUTION: Failure to observe any conditions set forth may cause
system malfunction and damage to smoke alarm.
CHECKOUT & TROUBLESHOOTING
1. Turn test knob to the NORMAL position and supply house power
to the smoke alarm. The red indicator should flash every 15-30
seconds, showing that the smoke alarm is operating properly.
2. If red light is not flashing or the green LED is not on:
a. Check that the battery is installed.
b. Check to see if the plug is in the outlet.
c. If the power and wiring check out, but the red light does not flash or
the green LED is still off, return the device to the manufacturer. See
TO RETURN A SMOKE ALARM.
3. Testing with the Test Knob:
a. Rotate test knob counter-clockwise to TEST 1 position, wait up to
20 seconds for smoke alarm to sound and visual signal flash. If
device does not sound after 20 seconds, return device for service.
b. After successfully testing smoke alarm, return test knob to
NORMAL (non-test) position and wait 20 seconds for the smoke alarm
to stop sounding.
Figure 15
c. To test unit for high sensitivity, turn test knob clockwise to TEST 2
position. Smoke alarm should remain silent. Return knob back to
normal position. If the unit sounds during test, the device's sensitivity
has become too high and may cause false alarms. This could mean
the smoke alarm is dirty and should be cleaned as described in
maintenance procedure below. If the smoke alarm continues to alarm
for TEST 2 position following cleaning return it to Gentex for service.
d. To check for proper smoke entry into smoke alarm's sensing
chamber. Gentex recommends using the Home Safeguard Smoke
Detector Spray or CHEKKIT® SMOKE Detector Tester from SDI.
This test should be performed once a year and should be sprayed
from a distance no closer than 12 inches from device.
MAINTENANCE
When smoke alarm has been in operation for a period of time or it
was installed prior to the completion of all building construction, the
device can become more sensitive due to dirt build-up in smoke
alarm's optic sensing chamber which could cause nuisance alarms or
could cause activation from small amounts of smoke build-up.
If this should occur, following this simple washing procedure will
restore your smoke alarm back to its original condition.
For further information, regarding frequency of cleaning and test-
ing, refer to NFPA 72, NFPA, Batterymarch Park, Quincy, MA 02269.
NOTICE: Failure to follow full cleaning instructions could result
in damage to this smoke alarm. DO NOT remove all smoke
alarms at the same time for cleaning.
1. Rotate smoke alarm counter-clockwise to remove it from its
mounting plate.
2. Unplug electrical power cord to smoke alarm and remove battery.
3. Select three (3) standard size wash buckets and fill them each with
one gallon of normal tap water (distilled or de-ionized treated water is
recommended as a final rinse if water is extremely hard in your area).
4. Add 1/8 cup of Ivory dishwashing liquid to first bucket of water,
mix thoroughly. Place one dirty smoke alarm into soap water mixture
For a period of 12 months from the date of purchase, or a maximum of 18 months from the date of manufac-
ture, Gentex warrants to you, the original consumer purchaser, that your Smoke Alarm will be free from defects
in workmanship, materials, and construction under normal use and service. If a defect in workmanship, materi-
als, or construction should cause your Smoke Alarm to become inoperable within the warranty period, Gentex
will repair your Smoke Alarm or furnish you with a new or rebuilt replacement Smoke Alarm without charge to
you except for postage required to return the Smoke Alarm to us. Your repaired or replacement Smoke Alarm
will be returned to you free of charge and it will be covered under this warranty for the balance of the warranty
period.
This warranty is void if our inspection of your Smoke Alarm shows that the damage or failure was caused by
abuse, misuse, abnormal usage, faulty installation, improper maintenance, or repairs other than those performed
by us.
ANY WARRANTIES IMPLIED UNDER ANY STATE LAW, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, APPLY ONLY FOR THE WARRANTY
PERIOD SPECIFIED ABOVE. PLEASE NOTE THAT SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
Important Notice:
These materials have been prepared by Gentex Corporation ("Gentex") for informational purposes only, are necessarily summary, and are not purported to serve as legal advice and should not be used as such. Gentex makes no representations and warranties, express or implied, that these
materials are complete and accurate, up-to-date, or in compliance with all relevant local, state and federal laws, regulations and rules. The materials do not address all legal considerations as there is inevitable uncertainty regarding interpretation of laws, regulations and rules and the
application of such laws, regulations and rules to particular fact patterns. Each person's activities can differently affect the obligations that exist under applicable laws, regulations or rules. Therefore, these materials should be used only for informational purposes and should not be used as a
substitute for seeking professional legal advice. Gentex will not be responsible for any action or failure to act in reliance upon the information contained in this material.
550-0094-TAB
until it becomes completely covered or submerged. NOTE: If smoke
alarms are exceptionally dirty, you may wish to first wipe off any
excess dirt before washing smoke alarm so as not to dirty the wash
water too quickly.
DO NOT open smoke alarm for cleaning. IF SMOKE ALARM IS
OPENED, PRODUCT WARRANTY BECOMES VOID.
NOTICE: ONLY IVORY DISHWASHING LIQUID IS TO BE USED.
OTHER BRANDS ARE NOT RECOMMENDED AND MAY CAUSE
YOUR SMOKE ALARM TO MALFUNCTION.
5. Allow smoke alarm to soak for approximately 10 minutes (longer if
extremely dirty). Agitate for 5 or 10 seconds to flush out any
remaining dirt left inside smoke alarm's housing.
6. Remove smoke alarm from wash water and transfer directly to one
of first rinse buckets containing clear water. Allow smoke alarm to
become completely submerged, agitate once more for 5 or 10 sec-
onds to remove soap residue.
7. Finally, transfer smoke alarm to second and final rinse bucket,
repeating method found in Step 6. Remove unit to a clean dry area
for a period of 48 hours to allow it to thoroughly dry.
NOTICE: SMOKE ALARMS ARE TO BE AIR DRIED ONLY. DO
NOT PLACE DEVICE IN OVEN, MICROWAVE OR USE A HOT AIR
BLOWER TO ACCELERATE DRYING TIME. THIS COULD RESULT
IN DAMAGE TO YOUR SMOKE ALARM.
IMPORTANT: IT IS RECOMMENDED TO CHANGE WASH AND
RINSE WATER AFTER FIVE (5) SMOKE ALARMS. IF YOUR
DEVICES ARE EXTREMELY DIRTY, WATER SHOULD BE
CHANGED MORE FREQUENTLY.
In the event you experience difficulty in the cleaning of device(s) or
if questions arise, please contact Gentex Corporation.
WARNING! If smoke alarm does not work properly, do not try and fix it
yourself. This will void your warranty. See "To Return a Smoke
Alarm" for instructions to return smoke alarm that does not operate
properly. DO NOT TRY TO FIX IT YOURSELF.
IMPORTANT: Gentex recommends smoke alarm be tested a
minimum of once a week.
WARNING! Never use an open flame of any kind to test your unit.
You may ignite and damage the smoke alarm as well as your home.
The test feature of your smoke alarm accurately simulates smoke
conditions and tests the device's functions as required by UL.
WARNING! Do not cover, tape, or otherwise block the openings of
smoke alarm. These openings are designed to allow air to pass
through your smoke alarm, thus sampling the air around the device.
WARNING! Smoke alarms are not to be used with detector
guards unless the combination has been evaluated and found
suitable for that purpose.
FAILURE TO REGULARLY CLEAN SMOKE ALARM WILL
RESULT IN FALSE ALARMS. A BUILD UP OF DUST CREATES AN
OBSCURATION THAT SIMULATES SMOKE. THIS MEANS UNIT
WILL GO INTO ALARM WITHOUT A FIRE CONDITION.
TO RETURN A SMOKE ALARM
Should you experience problems with your smoke alarm, proceed
as follows:
1. Rotate unit counter-clockwise to remove from its mounting plate.
2. Unplug electrical power cord or connector to smoke alarm and
remove battery. Do not ship smoke alarm with battery installed.
3. Carefully pack (manufacturer is not responsible for damage) and
return to manufacturer. Include complete details as to exact nature of
difficulties being experienced and date of installation.
4. Return to: Gentex Corp., 10985 Chicago Dr., Zeeland, MI 49464.
Prior to returning, call Gentex at 1-800-436-8391 or e-mail
FP_RMA@gentex.com to obtain RMA Number from return dept.
LIMITED WARRANTY
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
GENTEX WILL NOT BE LIABLE FOR ANY LOSS, DAMAGE, INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY KIND ARISING IN CONNECTION WITH THE SALE, USE, OR REPAIR OF THIS SMOKE
ALARM. PLEASE NOTE THAT SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
If a defect in workmanship, materials, or construction should cause your Smoke Alarm to become inoperable
within the warranty period, you must return the Smoke Alarm to Gentex postage prepaid. You must also pack
the Smoke Alarm to minimize the risk of it being damaged in transit. You must also enclose a return address.
Smoke Alarms returned for warranty service should be sent to: Gentex Corporation, 10985 Chicago Drive,
Zeeland, MI 49464.
If we receive a Smoke Alarm in a damaged condition as the result of shipping, we will notify you and you
must file a claim with the Shipper.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
GENTEX CORPORATION
10985 CHICAGO DRIVE, ZEELAND, MI 49464
PHONE: 1-800-436-8391
www.gentex.com
9-1-93
Page 7-6
Advertisement
