Front Glass Enclosure Panel Removal/Installa- Tion; Ment - Superior DRT6340TYN Installation And Operation Instructions Manual

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT6340/45TYN) • INSTALLATION INSTRUCTIONS
NOTE: Clean glass after first two weeks of
operation (after Burn-In period is over) and
then only when necessary and when the
fireplace is cool. Wipe surface with clean,
dampened, soft cloth. Follow with a dry, soft
towel as desired. Take care not to scratch the
glass surface.
WARNING: Do not use abrasive cleaners
on glass. Never clean the glass when it
is hot.
The viewing glass should be cleaned periodically
to remove any build-up caused from the
following:
• During start-up, it is normal for condensation
to form on the inside of the glass (this
condensation and fog will usually disappear
in a few minutes). The moisture can cause
lint, dust and other airborne particles to cling
to the glass surface.
• Initial curing of the high temperature paint
and burning off of lubricants used in the
manufacturing process may result in a film
on the glass.
• A white coating may form on the glass as a
result of impurities and minerals in the fuel.
It is recommended that the glass be cleaned
two or three times during each burning season,
depending on the circumstances present. The
following cleaning solutions are approved for use
to clean glass:
• Non-ammonia based household cleaner
• 50/50 mix of white vinegar & water
• Gas fireplace/stove glass cleaner
Inspect Glass Gasket
Visually inspect the gasket on the backside of the
glass enclosure panels. The gasket surface must
be clean, free of irregularities and seated firmly.
Clean Control Compartment
Keep control compartment clean by vacuuming
or brushing at least twice a year. More frequent
cleaning may be required due to excessive lint
from carpeting, bedding materials, etc. It is
important that control compartments, burners
and circulating air passageways of the appliance
be kept clean.
Clean Logs and Burner
Carefully remove the logs (use care when
handling the fiber logs, as they become quite
fragile after curing). Vacuum out any foreign
matter (lint, carbon, etc.) on the burner. Ensure
the burner ports are "open." Remove any carbon
deposits from the under side of the logs using
a vacuum cleaner, or a soft bristled brush (i.e.
paint brush).
NOTE: Improperly positioned logs can create
carbon build-up and will alter the performance
of the appliance.
Replacing Logs
If the logs become damaged by accident or
improper handling and need replacement,
use only the proper replacement logs from
manufacturer (see Page 45 for ordering
information).
Re-install Embers, Volcanic stone and Logs
Carefully follow placement instructions on
Pages 14 and 15). All logs should fit onto
corresponding pins and/or log stoppers. This
will ensure a proper flame and safe combustion.
NOTE: If installing the contemporary burner/
floor kit, skip this step and instead refer to the
instructions provided with the kit.
Inspect Wiring
Refer to wiring diagram on Page 48.
CAUTION: Label all wires prior to
disconnection when servicing controls.
Wiring errors can cause improper and
dangerous operation. Verify proper
operation after servicing.
ATTENTION: Au moment de l'entretien
des commandes, étiquetez tous les
fils avant de les débrancher. des
erreurs de cáblage peuvent entraîner
un fonctionnement inadéquat et
dangereux.
Inspect and clean all wire connections. Ensure
there is no melting melting or other damage.
Inspection should include:
• Terminals at the valve
• Wall ON/REMOTE/OFF switch
Low Battery Power Detection
The life span of the remote control system
batteries depends on many factors:
• the quality of the batteries used
• the number of appliance ignitions
• etc.
When the batteries are low, the receiver will
emit two (2) beeps (low battery alert) when
it receives a command from the transmitter.
After the batteries are replaced, the receiver will
emit one (1) beep when it receives a command
from the transmitter. See "Initialization of the
System" in the Installation Instructions.
Inspect Burner Flame and Pilot Flame Appearance
Periodically do a visual check of the burner
flame and the pilot flame. Ensure that the
burner flame appearance resembles the flame
shown in Figures 62 and 63 and as described
in Flame Appearance and Sooting on Page
43. Refer to Figure 64 on Page 43 for more
information about the pilot flame appearance.
Contact a qualified service technician at once if
any abnormal condition is observed.
Small Area Paint Touch-up
Only use a factory supplied paint kit for touch-
ups. Paint is available at your local Innovative
Hearth Products dealer. Never attempt to paint
a hot fireplace.
If the surface later becomes stained or marred,
it may be lightly sanded and touched up with
spray paint.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Front Glass Enclosure Panel Removal
and Installation
WARNING
• When reinstalling the glass
door, the door latch screws
must be securely tightened
to prevent the glass door
from falling out, which could
potentially cause damage and
possible injury.
• Do not attempt to substitute the
materials used on this door,
or replace cracked or broken
glass.
• Handle this glass with extreme
care! Glass is susceptible to
damage - Do not scratch or
handle roughly while reinstall-
ing the glass door frame.
• The glass door of this appli-
ance must only be replaced
as a complete unit as provided
by the manufacturer. Do not
attempt to replace broken,
cracked or chipped glass sepa-
rately.
• Do not attempt to touch the
front enclosure glass with your
hands while the fireplace is in
use.
WARNING
Do not operate appliance with
the glass front removed, cracked
or broken.
AVERTISSEMENT
Ne pas utiliser l'appareil si le
panneau frontal en verre n'est
pas en place, est craqué ou
brisé.
(Front Glass Enclosure Panel Removal
and Installation continued on following
page)
39