Technical Data; Optional Accessories; What To Do If - Bosch WTC84101GB Instruction Manual

Technical data

Dimensions (DxWxH)
Weight
Max. capacity
Condensation container
Ambient temperature
Connection voltage
Connected load
Fuse protection
Product number
Production number
You can find the rating plate on the back of the dryer.
Consumption rates
Residual moisture in the
Fabrics/programmes
fabrics after spinning
Cottons 6 kg
. Cupboard Dry* 1400 rpm
1000 rpm
800 rpm
Iron Dry* 1400 rpm
1000 rpm
800 rpm
Easy-Care 3 kg
. Cupboard Dry* 800 rpm
600 rpm
* Programme setting for testing in accordance with applicable standard EN61121.
** The values may differ from those specified, depending on the type of fabric, composition of
laundry to be dried, residual moisture in the fabric and the amount of laundry being loaded.
Fabrics/programmes Drying time
Cottons 6 kg / 3 kg*
. Cupboard Dry*** 85 min / per cycle
***Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.

Optional accessories

Washer-dryer stack connection set
WTZ
The dryer can be placed on top of a suitable washing machine with the same width and depth
11311
to save space. The dryer must be fastened on the washing machine with this connection set.
If the worktop of the washing machine is less than 544 mm deep, please consult the
after-sales service or your specialist retailer.
Platform
WMZ
For easier loading and unloading. The basket contained in the drawer can be used to carry
20500
the laundry.
60 x 60 x 85 cm
approximately 35 kg
6 kg
approx. 4.2 l
5 - 35 °C
220 - 240 V
2600 W
13 A
Rating plate or inside of the door
Drying time**
consumption**
13 A
(50%) 92 min
(60%) 110 min
(70%) 128 min
(50%) 75 min
(60%) 90 min
(70%) 105 min
(40%) 44 min
(50%) 55 min
Annual energy consumption
465 kWh / per year
(from after-sales service using order number)

What to do if ...

If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales
service. We will always find an appropriate solution and will avoid unnecessary visits by
engineers. Trust the expertise of the manufacturer and rest assured that the repair will be
carried out by trained service technicians using original spare parts. The contact details of your
local after-sales service can be found in the enclosed after-sales service directory, or by
calling one of these numbers:
– GB 0844 8928979 (Calls from a BT landline will be charged at up to 3 pence per minute.
A call set-up fee of up to 6 pence may apply.)
– IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
When contacting the after-sales service, please quote the appliance's product number (E no.)
and production number (FD) (see the inside of the door).
Set the programme selector to Off and remove the appliance plug from the socket.
Start/Stop indicator lamp does
not light up.
The display panel light and
indicator lights (depending on
model) go out and the
Energy
Start/Stop indicator light
flashes.
13 A
Container empty / clean filter/air
3.19 kWh
cooler indicator lights up.
3.83 kWh
Container empty / clean filter/air
4.47 kWh
cooler indicator light flashes.
2.44 kWh
2.93 kWh Dryer does not start.
3.42 kWh
Programme terminated shortly
1.27 kWh
after the start.
1.59 kWh
Water is leaking out.
The door opens by itself.
The required degree of dryness
was not achieved or the drying
time was too long.
Laundry damp.
The humidity in the room has
increased significantly.
One or more indicator lights are
flashing.
Power failure.
9
Mains plug plugged in?
Programme selected?
Check the socket fuse.
Energy-saving mode is activated see the separate
Energy-saving mode instructions.
Empty container for condensation see page 4.
Clean the fluff filter under running water
Clean the air cooler, if required see page 6.
Has the Start/Stop button been pressed?
Door closed?
Programme set?
Ambient temperature greater than 5 °C?
Make sure the dryer is level.
Push the door closed until you hear it engage.
Clean the fluff filter see page 4.
Empty the container for condensation.
Ambient temperature higher than 35 °C
room.
Air inlet may be blocked clear obstruction.
Unsuitable programme selected? see page 7.
Dryer installed too closely to other objects? Provide
adequate air circulation.
Mains failure Restart the dryer.
Fine layer of limescale on the moisture sensors. Clean the
sensors see page 6.
Use the next drying programme up or use the timed
programme as a supplement see page 7.
Warm laundry feels damper than it really is!
Make sure the room is sufficiently ventilated.
Air inlet blocked? Clear obstruction.
Make sure that the air cooler is inserted.
Clean the fluff filter and air cooler under running water
see page 4/6.
Check the installation conditions see page 8.
Switch off, allow to cool, switch back on and restart the
programme.
Remove the laundry from the dryer immediately and
spread it out. Heat may escape.
see page 4.
ventilate the
10