Toshiba GN-1041 Operator's Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. All in One Printer
  5. GN-1041
  6. Operator's manual
Toshiba GN-1041 Operator's Manual

Toshiba GN-1041 Operator's Manual

Toshiba gn-1041 multifunctional digital system wireless lan module operator's manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

MULTIFUNCTIONAL DIGITAL SYSTEMS
Operator's Manual for
Wireless LAN Module
GN-1041

Advertisement

Table of Contents
loading

Related Manuals for Toshiba GN-1041

Summary of Contents for Toshiba GN-1041

  • Page 1 MULTIFUNCTIONAL DIGITAL SYSTEMS Operator’s Manual for Wireless LAN Module GN-1041...

  • Page 2: Precautions

    (Revision B/G). Wireless Interoperability The TOSHIBA Wireless LAN products are designed to be interoperable with any Wire- less LAN products that is based on Direct Sequence Spread Spectrum (DSSS)/Orthog- onal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to: •...

  • Page 3: Limitation Of Liability

    Bluetooth™ and Wireless LAN devices operate within the same radio frequency range and may interfere with one another. If you use Bluetooth™ and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network perfor- mance or even lose your network connection. GN-1041 Operator’s Manual — PRECAUTIONS...

  • Page 4: Regulatory Information

    (10 MHz-300 GHz) Hereby, TOSHIBA TEC, declares that this GN-1041 is in compliance with the essential require- ments and other relevant provisions of Directive 1999/5/EC. TOSHIBA TEC vakuuttaa täten että GN-1041 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä...

  • Page 5: Usa-Federal Communications Commission (Fcc)

    Bij deze verklaart TOSHIBA TEC dat deze GN-1041 voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC. Par la présente TOSHIBA TEC déclare que l'appareil GN-1041 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE Par la présente, TOSHIBA TEC déclare que ce GN-1041 est conforme aux exigences essen-...

  • Page 6: Regulatory Notice For Channel Use In France

    • The contents of this document are believed to be accurate, however if any discrep- ancies noted should be brought to the attention of TOSHIBA authorized dealer or service engineer. • Notwithstanding the foregoing, the manufacturer is unable to accept any claims for losses or lost profits, etc.

  • Page 7: Table Of Contents

    Canada - Industry Canada (IC) ............4 Europe - EU Declaration of Conformity ..........4 USA-Federal Communications Commission (FCC) ......5 Regulatory Notice for Channel Use in France........6 Approved Countries/Regions for use for the Toshiba Wireless LAN..6 NOTES! .....................6 Table of Contents ...................7 1. Setting Up Wireless Network................9 Before Setting Up Wireless Network ............10...
  • Page 8 —...

  • Page 9: Setting Up Wireless Network

    This section describes about the preparations before setting up the wireless settings of the equipment. • Before Setting Up Wireless Network.....................10 • Setting Up the Infrastructure Mode ....................13 • Setting up the Ad Hoc Mode ......................35 • Disabling Wireless Network ......................44 GN-1041 Operator’s Manual...

  • Page 10: Before Setting Up Wireless Network

    1. Setting Up Wireless Network Before Setting Up Wireless Network Thank you for purchasing the GN-1041 Wireless LAN Module. This product is a wireless LAN Module using the 2.4 GHz spectrum diffusion system, and is compatible with IEEE Standard 802.11g and 802.11b for wireless LAN.

  • Page 11: Determine The Ssid

    PKCS#7 encoding format) in the equipment. This equip- ment uses the user certification file to authenticate the access rights to the wireless net- work, and the RADIUS server authenticate this equipment using the user ID and password. GN-1041 Operator’s Manual — Before Setting Up Wireless Network...
  • Page 12 Mode and the Access Point supports WPA/WPA2/802.1x or WPAPSK/ WPA2PSK, it is recommended to use WPA/WPA2/802.1x or WPAPSK/WPA2PSK rather than WEP. The WEP authentication is available for both the Infrastructure Mode and Ad Hoc Mode. GN-1041 Operator’s Manual — Before Setting Up Wireless Network...

  • Page 13: Setting Up The Infrastructure Mode

    Press the [USER FUNCTIONS] button on the control panel to enter the User Functions menu. Press the [ADMIN] button. • The ADMINISTRATOR PASSWORD screen is displayed. Press the [PASSWORD] button. • The input screen is displayed. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 14 • The WIRELESS SETTINGS menu is displayed. Press the [WIRELESS SETTINGS] button. • The WIRELESS SETTINGS screen is displayed. NOTE: It may take a time to display the WIRELESS SETTINGS screen. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 15 The NETWORK TYPE screen is displayed. Press the [INFRASTRUCTURE] button and press the [NEXT] button. The SSID SETTINGS screen displayed. • Continue to the procedure for specifying the SSID. P.16 "Specify SSID" GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...

  • Page 16: Specify Ssid

    This Wireless LAN supports only channel 1 to 11. This equipment cannot connect the Access Point that uses the other channel than these channels. Please make sure to set the channel between 1 to 11 in the Access Point. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 17 The WIRELESS LAN SECURITY SETTINGS screen is dis- played. • Continue to the procedure for specifying the Security Mode. P.19 "Select Security Mode" Entering the SSID manually Press the [SSID] button. • The letter entry screen is displayed. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 18 The screen returns to the SSID SETTINGS screen. Press the [NEXT] button. The WIRELESS LAN SECURITY SETTINGS screen is dis- played. • Continue to the procedure for specifying the Security Mode. P.19 "Select Security Mode" GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...

  • Page 19: Select Security Mode

    When the [WPA] or [WPA2] button is selected, TKIP or AES(CCMP) can be selected. • When GN-1040 is connected, the [WPA], [WPA2], and [WPA2PSK] buttons cannot be selected. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 20 [ENTER] button. • The screen returns to the WIRELESS AUTHENTICATION (EAP-TLS) screen. NOTE: In the EAP USER NAME, enter the user name in “User Name@FQDN” format. Example: wlanuser@toshiba.com GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 21 Enter the value using the keyboard and digital keys, and press the [ENTER] button to set the entry. Specify the following items and press the [NEXT] button. ENCODING FORMAT Select the encoding format of the CA certification file. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 22 [ON] button is selected, press the [RADIUS SERVER NAME] button to enter the RADIUS server name. NOTE: In the RADIUS SERVER NAME, enter the user name in “Server Name@FQDN” format. Example: wlanserver@toshiba.com ENCRYPTION INTENSITY Select the encryption intensity. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 23 When 802.1x is selected for the security mode and GN-1040 is used, either [TKIP], [AES(CCMP)], or [Dynamic WEP] can be selected. • When 802.1x is selected for the security mode and GN-1041 is used, only [Dynamic WEP] can be selected. SUPPLEMENT: The encryption intensity between each encryption is: AES(CCMP) >...
  • Page 24 When using the WPA/WPA2/802.1x authentication with the PEAP protocol, you must install the CA certification file in the equipment using TopAccess first. For instructions on how to install the CA certification using TopAccess, please see TopAccess Guide. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 25 NOTE: In the EAP USER NAME, enter the user name in “User Name@FQDN” format. Example: wlanuser@toshiba.com [EAP PASSWORD] Press this to enter the EAP password that is used for the authentication. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 26 In the RADIUS SERVER NAME, enter the user name in “Server Name@FQDN” format. Example: wlanserver@toshiba.com ENCRYPTION INTENSITY Select the encryption intensity. When the PEAP protocol is selected, only [LOW] can be selected. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 27 When 802.1x is selected for the security mode and GN-1040 is used, either [TKIP], [AES(CCMP)], or [Dynamic WEP] can be selected. • When 802.1x is selected for the security mode and GN-1041 is used, only [Dynamic WEP] can be selected. SUPPLEMENT: The encryption intensity between each encryption is: AES(CCMP) >...
  • Page 28 PSK Path Phrase must be assigned in both the Access Point and other wireless devices. If the PSKs are same between the Access Point and other wireless devices, the Access Point allows them to access the wireless network through the Access Point. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 29 When pressing the [PSK PASS PHRASE] button, the letter entry screen is displayed. Enter the value using the keyboard and digital keys, and press the [ENTER] button to set the entry. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 30 If you want to change the settings, press the [PREV] button to move back to the screen that you want to change and then repeat the operation. Press the [YES] button to shut down the equipment. • The wireless settings apply after restarting the equipment. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 31 SUPPLEMENT: When pressing the [WEP KEY button, the letter entry screen is displayed. Enter the value using the keyboard and digital keys, and press the [ENTER] button to set the entry. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 32 If you want to change the settings, press the [PREV] button to move back to the screen that you want to change and then repeat the operation. Press the [YES] button to shut down the equipment. • The wireless settings apply after restarting the equipment. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 33 [AUTO]. When [AUTO] is selected, this equipment will use appropriate rate depending on the condition. Generally select [AUTO]. The communication may fail unexpectedly if you select a static transmit rate. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...
  • Page 34 If you want to change the settings, press the [PREV] button to move back to the screen that you want to change and then repeat the operation. Press the [YES] button to shut down the equipment. • The wireless settings apply after restarting the equipment. GN-1041 Operator’s Manual — Setting Up the Infrastructure Mode...

  • Page 35: Setting Up The Ad Hoc Mode

    Press the [USER FUNCTIONS] button on the control panel to enter the User Functions menu. Press the [ADMIN] button. • The ADMINISTRATOR PASSWORD screen is displayed. Press the [PASSWORD] button. • The input screen is displayed. GN-1041 Operator’s Manual — Setting up the Ad Hoc Mode...
  • Page 36 The WIRELESS SETTINGS menu is displayed. Press the [WIRELESS SETTINGS] button. • The WIRELESS SETTINGS screen is displayed. Press the [ON] button and press the [NEXT] button. • The NETWORK TYPE screen is displayed. GN-1041 Operator’s Manual — Setting up the Ad Hoc Mode...
  • Page 37 You can specify the between 1 to 11 for the channel. However, if there is a channel that has already been used for Ad Hoc network, use the same channel. The SSID SETTINGS screen displayed. • Continue to the procedure for specifying the SSID. P.16 "Specify SSID" GN-1041 Operator’s Manual — Setting up the Ad Hoc Mode...

  • Page 38: Specify Ssid

    The letter entry screen is displayed. Enter the SSID using the keyboard and digital keys and press the [ENTER] button. • The screen returns to the SSID SETTINGS screen. Press the [NEXT] button. GN-1041 Operator’s Manual — Setting up the Ad Hoc Mode...
  • Page 39 1. Setting Up Wireless Network The WIRELESS LAN SECURITY SETTINGS screen is dis- played. • Continue to the procedure for specifying the Security Mode. P.19 "Select Security Mode" GN-1041 Operator’s Manual — Setting up the Ad Hoc Mode...

  • Page 40: Select Security Mode

    Enter the following items and press the [NEXT] button. WEP ENCRYPTION Select the bit length of the WEP key. KEY ENTRY METHOD Select the character code for the WEP key. GN-1041 Operator’s Manual — Setting up the Ad Hoc Mode...
  • Page 41 The shut down screen is displayed. SUPPLEMENT: If you want to change the settings, press the [PREV] button to move back to the screen that you want to change and then repeat the operation. GN-1041 Operator’s Manual — Setting up the Ad Hoc Mode...
  • Page 42 • Select the low transmit power if you want to limit the area that the wireless communication is enabled. If you do not have to limit the area, select [100%]. GN-1041 Operator’s Manual — Setting up the Ad Hoc Mode...
  • Page 43 If you want to change the settings, press the [PREV] button to move back to the screen that you want to change and then repeat the operation. Press the [YES] button to shut down the equipment. • The wireless settings apply after restarting the equipment. GN-1041 Operator’s Manual — Setting up the Ad Hoc Mode...

  • Page 44: Disabling Wireless Network

    • The input screen is displayed. Enter the administrator password and press the [ENTER] button. • The ADMIN menu is displayed. Press the [WIRELESS SETTINGS] button. • The WIRELESS SETTINGS menu is displayed. GN-1041 Operator’s Manual — Disabling Wireless Network...
  • Page 45 The NETWORK TYPE screen is displayed. Press the [FINISH] button. • The shut down screen is displayed. Press the [YES] button to shut down the equipment. • The wireless settings apply after restarting the equipment. GN-1041 Operator’s Manual — Disabling Wireless Network...
  • Page 46 1. Setting Up Wireless Network GN-1041 Operator’s Manual — Disabling Wireless Network...

  • Page 47: Appendix

    2. Appendix APPENDIX This section describes the specification and glossary of terms. • Specification............................48 • Troubleshooting ..........................49 • Glossary............................50 GN-1041 Operator’s Manual...

  • Page 48: Specification

    Microsoft Windows 2000/2003 Server (WiFi Standard) *2 Supported RADIUS server Microsoft Windows 2000/2003 Server (WiFi Standard) Operation Mode Infrastructure Mode, Ad Hoc Mode Wireless ON/OFF Available Wired LAN/Wireless LAN Not Available Simultaneous Operation Wireless LAN/Bluetooth Available Simultaneous Operation GN-1041 Operator’s Manual — Specification...

  • Page 49: Troubleshooting

    This equipment uses the certificate that the RADIUS server does not support. Unknown ca Installed CA certificate cannot verify the server certifi- cate in the RADIUS server. Make sure to install a cor- rect CA certificate. Unable to connect GN-1041 Operator’s Manual — Troubleshooting...

  • Page 50: Glossary

    System to integrate wireless LAN with wired LAN LAN (Local Area Network) A network configured from mutual connections between computers within a limited area. Also called an "intranet" or "business or regional data communications network." GN-1041 Operator’s Manual — Glossary...
  • Page 51 A method of transmission in which signals that are normally transmitted over a given limited frequency band undergo narrow band modulation (primary modulation), then again diffuse modulation (secondary modulation) to intentionally diffuse the signal over a broad frequency spectrum. GN-1041 Operator’s Manual — Glossary...
  • Page 52 2. Appendix GN-1041 Operator’s Manual — Glossary...

  • Page 53: Index

    INDEX INDEX INDEX...
  • Page 54 INDEX Numerics .......... 11 802.1x ............ 37 AD HOC ..........11 Ad Hoc Mode ..........12 AES(CCMP) ......16 AVAILABLE NETWORK ........22 CA CERTIFICATE ........25 EAP PASSWORD ........20 EAP USER NAME ..........11 EAP-TLS ......21 ENCODING FORMAT ENCRYPTION BETWEEN AP AND STA.....22 ENCRYPTION INTENSITY ..22...
  • Page 55 GN-1041 OME05009000...
  • Page 56 MULTIFUNCTIONAL DIGITAL SYSTEMS Operator’s Manual for Wireless LAN Module GN-1041 2-17-2, HIGASHIGOTANDA, SHINAGAWA-KU, TOKYO, 141-8664, JAPAN R05082091200-TTEC 2005-10 ©2005 TOSHIBA TEC CORPORATION All rights reserved...

Table of Contents