Honeywell HDZ30A Quick Installation Manual

HDZ Series Analogue PTZ Dome Quick Installation Guide
800-16525 - Rev B - 07/2014

Cautions and Warnings

RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING Installation and servicing should be performed only by qualified
and experienced technicians to conform to all local codes and to maintain your
warranty.
WARNING To ensure compliance with electrical safety standards, CSA
Certified/UL Listed Class 2 power adapters are required.
FCC Statement of Compliance
Information to the User: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Note Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
Manufacturer's Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the
European Parliament and Council Directive on the Restrictions of the use of certain Hazardous
Substances in electrical and electronic equipment (2011/65/EU), General Product Safety Directive
(2001/95/EC) and the essential requirements of the EMC Directive (2004/108/EC), conforming to the
requirements of standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60950-1 for
electrical equipment safety.
CAUTION
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
WARNING To comply with EN50130-4 requirements, a UPS should be
employed when powering the camera from 24 V AC.
Waste Electrical and Electronic Equipment (WEEE)
Correct Disposal of this Product (applicable in the European Union and other
European countries with separate collection systems).
This product should be disposed of, at the end of its useful life, as per applicable local
laws, regulations, and procedures.

Safety Instructions

Before installing or operating the unit, read and follow all instructions. After
installation, retain the safety and operating instructions for future reference.
1. HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.
2. INSTALLATION
• Install in accordance with the manufacturer's instructions.
• Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
• Do not install indoor rated models in outdoor locations.
• Any wall or ceiling mounting of the product should follow the manufacturer's instructions
and use a mounting kit approved or recommended by the manufacturer.
3. POWER SOURCES - This product should be operated only from the type of power source
indicated on the marking label.
4. HEAT - Situate away from items that produce heat or are heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers).
5. MOUNTING SYSTEM - Use only with a mounting system recommended by the manufacturer,
or sold with the product.
6. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as
they may result in the risk of fire, electric shock, or injury to persons.
7. ACCESSORIES - Only use accessories specified by the manufacturer.
8. CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
9. SERVICING - Do not attempt to service this unit yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
10.
REPLACEMENT PARTS - When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the same
characteristics as the original part. Unauthorized substitutions may result in fire, electric shock
or other hazards. Using replacement parts or accessories other than the original
manufacturers may invalidate the warra
CAUTION
Risk of explosion if Battery is replaced by an incorrect type. Dispose of
used batteries in accordance with local laws.
Document 800-16525 – Rev B – 07/2014
nty.

Before You Begin

The Honeywell HDZ Series True Day/Night Analogue PTZ dome camera is a high
resolution PTZ camera series designed for use in a wide range of applications. This guide
is intended for basic installation and setup information. Please refer to the HDZ Series
Analogue PTZ Dome Camera User Manual for more thorough information. This guide is
intended for use with the following HDZ Series cameras:
• HDZ30A(X): HDZ Series Indoor Analogue PTZ Dome, 30x zoom, NTSC/PAL.
• HDZ36AE(X): HDZ Series Outdoor Analogue PTZ Dome, 36x zoom, NTSC/PAL.
Before you begin, check that you have received all of the parts listed below. If any parts
are missing or damaged, contact your dealer immediately.
Indoor models: • PTZ dome camera
HDZ30A
• Optical cover
HDZ30AX
• Honeywell logo label
• Hard ceiling mount
• Torx driver
Outdoor models: • PTZ dome camera
HDZ36AE
• Outdoor mount kit
HDZ36AEX
• Honeywell logo label
• Waterproof rubber
• Lubricant
• CD: User manuals

Installation Overview

Follow these general steps for installing the HDZ Series Analogue PTZ camera:
1. Choose an installation location. Ensure the mounting surface can support the
combined weight of the camera and mount before starting. The weight
requirements of each mounting option are listed in the installation section for that
mount (see Mounting the Camera on page
2. Assemble the camera (see Assembling the
3. Prepare the cables that will be needed for installation. Each camera requires a
power, video, and RS-485 connection (see
page 2). The RS-485 connection is needed to connect to a keyboard/controller.
Some installations may also require alarm input/output connections.
4. Use the corresponding dip switches to set the camera ID for the PTZ dome (see
Setting on page 2). This step is required if you have more than one PTZ dome in
your surveillance system.
5. Use the corresponding dip switches to set the camera control protocol for the PTZ
dome (see Setting the Camera Control Protocol on page
6. Start mounting the camera. Follow the instructions included for the specific mount
being used in your installation (see
secure the camera during installation by connecting a safety cable from a secure
part of the mounting structure to the eyelet on the back of the camera (see
Safety Cable During Installation on page
7. Route the cables through the mount and connect them to the camera and
peripheral devices (see Dip Switches and Cable Connections on page
8. Finish mounting the camera (see
9. Configure the camera with the connected keyboard/controller (see
PTZ Dome on page 4). Refer to the
Guide for detailed instructions on configuring the camera settings.

Assembling the Camera

Camera assembly is quick and easy. To assemble the camera:
1. Take the camera and all other components out of the packaging.
2. Rotate and remove the protective cover bag from the camera body.
3. Use the torx driver to remove the dome cover.
4. Remove the foam and tape from inside the dome.
5. Remove the lens cap from the camera lens.
6. Use the torx driver to fasten the dome cover to the camera body.
Note Optional: Use the lubricant on the dome cover's rubber ring to make it
easier to re-attach to the housing and seal the PTZ dome cover and
housing without water coming in. Be careful not to get any lubricant on
the dome as it may interfere with viewing PTZ images.
7. Leave the protective film on the dome cover until installation is complete.
• CD: User manuals
• Quick Installation Guide
• M4 screws (x4)
• Plastic anchors (x4)
• UTP balun accessory
• Optical cover
• M5 and M3 security and
standard screws (1 each)
• Quick Installation Guide
• Torx driver
• UTP balun accessory
3).
Camera, below).
Dip Switches and Cable Connections on
2).
Mounting the Camera on page 3). Make sure to
3).
2).
Mounting the Camera on page 3).
Configuring the
HDZ Series Analogue PTZ Dome Camera User
ID
Using