Advertisement
WARNING To comply with EN50130-4 requirements, a UPS should be
employed when powering the camera from 24 V AC.
Connecting Alarm Inputs/Outputs
Refer to the following figure and table when making alarm connections to your camera:
I/O 1 2 3 4 5 6 7 8 9 10 11 12
Pin
Definition
Pin
1
Alarm Out NO 1
5
2
Alarm Out NC 1
6
3
Alarm Out COM 1
7
4
GND
8
Mounting the Camera
Choosing a Camera Mount
You can install the camera to a ceiling, wall, pole, parapet, or roof using the following
Honeywell products:
Model No.
Description
HDZINBKT
In-Ceiling Bracket
HDCM1
Ceiling Mount
HDXWM2
Wall Mount
HDPRM2
Parapet/Flat Roof Mount
HDXCMA1
Corner Mount Adapter for HDXWM2
HDXPMA2
Pole Mount Adapter for HDXWM2
Refer to the installation instructions included with the mounts for more detailed
instructions on installing the mount and camera. See the following sections for more
information on installing the HDZ series camera with the HDCM1, HDXWM2, and
HDPRM2 mounts.
Note
If you are installing the camera with the HDZINBKT in-ceiling bracket,
follow the installation instructions included with the bracket.
Using Safety Cable During Installation
The HDZ Series camera includes an eyelet for attaching a safety cable to securely fix the
camera to the mounting structure. It is recommended that you install a safety cable (such
as a 3/32-in. [2.4 mm] plastic coated aircraft cable) to secure the camera to the building
structure. This will prevent the camera from falling during installation. The cable must be
strong enough to support the weight of the camera (4.9 lb [2.2 kg] for the indoor model,
5.7 lb [2.6 kg] for the outdoor model).
Eyelet location on indoor dome back panel
HDZ Outdoor Model Back Plate
Inputs (×4)
5 V, 4700 ohms,
pull up
Outputs (×2)
Relay output, 120
V AC/30 V DC
Definition
Pin
Definition
Alarm Out NO 2
9
Alarm In 4
Alarm Out NC 2
10
Alarm In 3
Alarm Out COM 2
11
Alarm In 2
GND
12
Alarm In 1
Indoor
HDZ Indoor Model Back Plate
Eyelet location on outdoor dome back panel
Installing an Indoor
Ceiling Mount (HDCM1)
The HDCM1 ceiling mount weighs 4 lb (1.8
kg) and can be installed directly to a load-
bearing ceiling. HDCM1 has a maximum
load rating of 26 lb (11.7 kg) and is for
indoor use only.
1.
Ensure that the ceiling can support the
combined weight of the camera and
the mount (at least 8.8 lb [4.0 kg]).
2.
Make a cable entry hole in the ceiling.
3.
Feed the cables through the mount,
leaving approximately 1 ft (0.3 m)
extending past the end of the mount.
Note
If you are using the recommended
safety cable, feed it through the
mount and attach one end to the
camera eyelet and the other end to
the building structure.
4.
Attach the mount to the ceiling using
appropriate hardware.
5.
Feed the cables through the indoor
mount kit and screw the mount kit
onto the ceiling mount.
6.
Connect the cables to the camera
(see previous section:
and Cable
Connections). Connect the
video output port either to a coaxial
cable (with BNC connection) or with
Outdoor
optional UTP balun accessory if
unshielded twisted pair cabling is
used.
Note
Check that the eyelet cable
connection is secure and carrying
all of the load of the camera after
making all cable connections.
7.
Attach the camera to the mount kit,
and then tighten the security screw on
the top of the camera.
Installing an Indoor/Outdoor Wall Mount (HDXWM2)
The HDXWM2 wall mount weighs 3.2 lb (1.45 kg) and can be installed directly to a load-
bearing wall, or to a corner or pole using an appropriate adapter. The mount has a
maximum load rating of 26 lb (11.7 kg) and can be installed indoors or outdoors.
1.
Ensure that the mounting surface can support the combined weight of the camera
and the mount (at least 8.9 lb [4.05 kg]).
2.
If you are using a corner or pole adapter, feed the cables through the cable access
hole of the adapter, and then attach the adapter to the mounting surface using
appropriate mounting hardware.
3.
Feed the cables through the mount, leaving approximately 1 ft (0.3 m) extending
past the end of the mount.
Optionally, you can feed the cables through the 0.75 in. (19 mm) conduit hole at the
base of the mount arm (see illustration).
Feed cables
through the
mount kit
Feed cables
through the
mount kit
Tighten the screw at
Dip Switches
the top of the camera
Screw the mount kit
onto the wall mount
Tighten the screw at
the top of the camera
after connecting the
three parts
Attach the
camera body
onto the mount
kit
Screw the
mount kit
onto the
ceiling
mount
Attach the
camera
body onto
the mount
kit
19 mm (0.75 in.)
cable access
hole for surface-
mounted conduit.
Cable access hole
for field service.
Advertisement
