Table of Contents
Advertisement
BEForE startInG a FlIGHt:
1. Pay attention to your surroundings:
•
Do not fly the helicopter in strong winds,
rain or at night.
•
Do not fly the helicopter near roads, rail-
ways or electrical lines.
2. Pre-flight checks:
•
Before starting always check to ensure
that there is no damage to any part and
that model responds and operates cor-
rectly.
•
Always be sure to check that all the mov-
ing parts are correctly positioned and
that all nuts bolts are suitably tightened.
•
Please ensure that the batteries for your
transmitter as well as your helicopter are
fully charged and operational.
wHIlst In opEratIon:
1. Always disconnect the battery when:
•
adjusting parts on the helicopter or trans-
mitter.
•
attaching or replacing parts.
•
any unusual noises or vibrations occur.
•
if any other potentially dangerous situa-
tions could occur.
2. When connecting the battery please ob-
serve the following procedures:
•
Be sure that the transmitters throttle is in
its lowest position.
•
Ensure the idle up function is disen-
gaged.
aFtEr a FlIGHt:
1. Inspect parts immediately. If any screws
seem loose or are missing be sure to re-
place or refit. If cracks or damage are
apparent please replace the components.
parts lIst:
modEls:
INT-400
INT-401
sparEs:
INT-001
INT-002
INT-003
INT-004
INT-005
INT-006
INT-007
INT-008
INT-009
INT-010
INT-011
INT-012
INT-013
INT-014
INT-015
INT-016
INT-017
INT-018
INT-019
INT-020
INT-021
INT-022
INT-023
INT-024
INT-025
INT-026
INT-027
INT-028
INT-029
INT-030
INT-031
INT-032
INT-033
INT-034
INT-035
INT-036
INT-037
INT-038
INT-039
INT-040
Main gear 138T (w/one way bearing)
INT-041
INT-042
INT-043
INT-044
INT-045
INT-046
INT-047
INT-048
INT-049
INT-050
INT-051
INT-052
INTERCEPTOR 400 KIT
INTERCEPTOR 400 ARF
Flush head screw M2x7
φ5 Ball with stand
Blade holder
Center hub CNC
Brg φ3xφ8x4 ZZ
Bearing collarφ3xφ5x4
M3 nylon nut
O-ring P3
Spindle bush
Feathering spindleφ3
φ2 Collar with stand
Pan head screw M2x4
Bearing spacer 2x3x1.5
Brg φ2xφ5x2.5 ZZ
Pan head screw M2X10mm
Seesaw (L)
Mixing Arm (L)
Stabilizer control set
Stabilizer bar
Stabilizer blade
Set screw M3x3
φ2.6 Bail radius pin
Swash plate set
M2 nylon nut
Pan head screw M2x12
φ5 Main mast
φ5 Mast lock
Needle pin 1.5x7
Wash-out control arm
Radius arm
Slide block
FW φ2xφ4x0.3T
Drive pulley 11T
Brg φ3xφ8x3 ZZ
Counter gear case
Counter gear 21T
E-ring E-2.5
Bearing block
Brg φ5x11x5 ZZ
Auto-ratation gear set
Auto-rotation drive shaft
Auto-rotation gear 105T
M2 nut
Radius arm stay set
Cabin cross member
Tapping screw M2x6
Elevator lever
Upper frame set (w/bearing)
Tail boom holder
Elevator shaft
Cross member M2x16
13
Advertisement
Table of Contents
