Playing Tracks Repeatedly (Repeat Play); Playing Tracks: Repeating A Specified Portion (Loop Play) - Sony MHC-GR5 Operating Instructions Manual

6
Repeat steps 4 and 5 to program the
remaining tracks you want to play in the
order you want them to play.
7
Press fl.
All the tracks play in the order you
choose.
To Press
Check the CHECK on the remote
1
program repeatedly*
Program a pause on the remote*
p (
Stop play on the remote)
Cancel program CONTINUE*
play
Erase a track CLEAR on the remote in
from the end stop mode
Erase a specific CHECK on the remote
track repeatedly so that the
number of the track
lights up, and press
CLEAR on the remote
p (
Erase the entire on the remote)
program once in stop mode or
twice while playing
* 1 After the last track appeared "CHECK
END" appears in the display.
* 2 "P" appears and the total playing time is
reset to 0.00.
* 3 The program is erased.
To change the order of
programmed tracks
To change the order, erase the entire
program and create a new one.
Notes
• The program you made remains in the CD
player even after it has been played back.
Press fl to play the same program again.
• If "--.--" appears instead of the total
playing time during programming, this
means:
– you have programmed a track number
which exceeds 20, or
– the total playing time has exceeded 100
minutes.
Playing Tracks
Repeatedly
(repeat play)
You can choose between two different
repeat play modes. One repeats all the
tracks in the current play mode; the other
repeats a single track.
Use the buttons on the unit to do this
operation.
POWER n ON
1
2
3
Repeating all the tracks
1 Press REPEAT once so that "REPEAT"
appears in the display.
1 2 3
2 Press fl.
Repeating a single track (in normal
play mode only)
Press REPEAT repeatedly while playing the
desired track until "REPEAT 1" appears in
the display.
DOLBY
OFF
1 2 3
To cancel repeat play
Press REPEAT so that "REPEAT" or
"REPEAT 1" disappears from the display.
Playing Tracks:
Repeating a
Specified Portion
(loop play)
You can use the loop function to record
from a CD to a tape with the sampler play.
Use the buttons both on the unit and
remote to do this operation.
EXAMPLE
Original song:
"Hey, come on everybody!"
When you use the loop function:
"Hey, come come come come come on
everybody!"
2
DOLBY NR
1 2 3 4 5
OFF
6 7 8
REPEAT
VOL
NR
1 2 3 4 5
6 7 8
1 DISC
REPEAT 1
VOL
POWER n ON
3,5
1
Press FUNCTION repeatedly until "CD"
appears in the display.
2
Press § OPEN/CLOSE and place a CD.
Then, press § OPEN/CLOSE again to
close the disc tray.
3
Press LOOP repeatedly to select
NORMAL or RHYTHM (as for
NORMAL and RHYTHM, see "What is
the difference between NORMAL and
RHYTHM?" for details).
NORMAL or RHYTHM has five modes
respectively, depending on the interval
you want. The display changes as
follows:
NORMAL1.....NORMAL5
RHYTHM5.....RHYTHM1
The interval (about 0.25 to 1.00 second)
becomes longer as the number gets
bigger.
4
Press fl.
5
Press and hold down LOOP when a
portion you want to repeat is played
and release when you want to stop
repeating it.
What is the difference between
NORMAL and RHYTHM?
There is a difference between NORMAL
and RHYTHM in restarting point of normal
play when the loop effect ends.
Select NORMAL or RHYTHM while stop
playing or pause playing.
NORMAL
Normal CD play resumes from the same
point as you have started the loop play
when you release LOOP button.
RHYTHM
The portion over-ridden by the loop effect
will be skipped and then normal play
resumes.
Chapter 2: the CD Player
4
2
1
EN
9