Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Tennant S8
Summary of Contents for Tennant S8
- Page 1 Battery Sweeper Operator Manual Model Part No.: MS85004 MS85904 UK 9001217 Rev. 01 (12-05) TENNANT N.V. Industrielaan 6 5405 AB P.O. Box 6 5400 AA Uden-The Netherlands europe@tennantco.com www.tennantco.com Home Find... Go To..
-
Page 2: Table Of Contents
Page 13 Replacing and adjusting the belts Page 14 Replacing the flaps Page 15 5.10 Replacing the adjusting the traction cable Page 15 Wiring diagram S8 Page 16 Troubleshooting Page 17 Scrapping the machine Page 17 CE Declaration Page 18... -
Page 3: Technical Features And Specifications
Technical features and specifications DESCRIPTION Maximum width with 838 mm 33 in side brush Maximum length with 1219 mm 48 in side brush Maximum height with 1010 mm 39.75 in handlebar Actual cleaning width with 520 mm 20,5 in main brush Actual cleaning width with 711 mm 28 in... - Page 4 SAFETY PRECAUTIONS: FOR SAFETY: This machine is intended for commercial use only. It is Do not operate machine: designed to pick up dirt, dry debris and dust from dry hard - In flammable or explosive areas. floor or carpeted surfaces in an indoor environment. It is not - Unless trained and authorized.
-
Page 5: Safety Labels
1.1 -SAFETY LABELS The safety label appears on the machine in the location indicated. Replace label if it is missing or if it becomes damaged or illegible. BATTERY CHARGE LABEL – LOCATED ON TOP OF THE BATTERY CHARGER WARNING: Fire Explosion Hazard. -
Page 6: Serial Number And Ce Marking
1.2 -SERIAL NUMBER AND CE MARKING 2.1 -PREPARING THE MACHINE FOR OPERATION Always ensure that the machine is provided with a rating plate giving 2.1.1 -Mounting the side brush the serial number and CE marking in the position shown in Fig.1. - Switch the brush lift lever (1 Fig.3), to OFF. - Page 7 - To ensure that the traction lever works properly make sure To Install Battery: the lever cable is positioned as shown before replacing the 1. Remove key from machine. rear shroud. 2. Open the front hood to access the battery compartment. (Fig.2/C) 3.
-
Page 8: Controls
3.1 -CONTROLS Fig. 3 1) Side brush control lever: switch the lever to lower 6) Traction lever: By pulling this lever, the machine will start position and the side brush will move into the work moving forward position and start spinning. To stop the side brush, switch the lever to upper position. -
Page 9: Operating Machine
4.1 -OPERATING MACHINE 4.3 -CLEANING THE WASTE BINS FOR SAFETY: Do not operate machine unless trained Before carrying out this operation, make sure the machine is and authorized. When using machine, do not pick up turned off completely. liquids or leave unattended. Before leaving machine remove key and never allow children to play on or around (*)ATTENTION: WASTE... -
Page 10: Routine Maintenance
5.1 -ROUTINE MAINTENANCE 5.2 -BATTERY MAINTENANCE FOR SAFETY: When servicing machine all repairs must The battery must be kept clean and dry. Keep the terminals be performed by an authorized service person. Use and poles clean. For Wet (lead acid) Battery - Every 10 hours, manufacturer supplied or approved replacement parts remove the caps and check the electrolyte level. -
Page 11: Charger Troubleshooting And Error Codes
5.3 -CHARGER SETTINGS IMPORTANT: The on-board battery charger is factory set to accommodate a SEALED (GEL) battery. To use a WET (lead acid) battery with the machine, the charger's internal dipswitches must be reconfigured as shown below. Failure to follow these instructions will result in battery damage. WET (lead acid) BATTERY DIPSWITCH PANEL CONFIGURATION SEALED (GEL) BATTERY DIPSWITCH CONFIGURATION Fig. -
Page 12: Filter Maintenance
5.5 -FILTER MAINTENANCE Cleaning the filter The filter is one of the machine's main components. It is essential to achieve the best results from your machine. If you notice that dust forms when the machine is at work, check the filter. -
Page 13: Replacing And Adjusting The Side Brush
5.6 -REPLACING AND ADJUSTING THE SIDE BRUSH 5.7 -REPLACING AND ADJUSTING THE MAIN BRUSH Replacing Replacing (Fig.6/C) After lifting the front part of the machine, replace the side To replace the main brush, remove the front bin and slacken brush by removing the brush fixing screw Fig. 2, and the four fixing screws to remove the brush. -
Page 14: Replacing And Adjusting The Belts
5.8 -REPLACING AND ADJUSTING THE BELTS To prepare the machine for belt replacement, carry out the following operations: - remove the top cover and the front bin. 5.8.1 -Replacing the side brush belt - Remove the right wheel, screw out the screws that fix the bumper and the lateral right guard and remove them. -
Page 15: Replacing The Flaps
5.9 -REPLACING THE FLAPS 5.10 -REPLACING THE TRACTION CABLE 5.9.1 -Outer side flaps 5.10.1 -Remove the traction cable as follows To replace the side flaps pos.1 Fig.9, remove the rear wheels To replace the traction cable proceed as follows: and the relevant side guards. Loosen the screws that secure - Remove the upper bonnet of the machine. -
Page 16: Wiring Diagram S8
6.1 -WIRING DIAGRAM M1 Main brush motor F3 30A fuse M2 Traction motor S1 Key switch M3 Fan motor S2 Fan switch F1 50A Bar fuse Car.Batt Battery recharge socket F2 1A/250V fuse - 16 - Home Find... Go To.. -
Page 17: Troubleshooting
6.2 -TROUBLESHOOTING 6.3 -SCRAPPING THE MACHINE In the event the machine must be scrapped, please remember that batteries are not common waste materials. They must be disposed of in accordance with the relevant FAULT CAUSE REMEDY laws. The belt is broken Replace The machine is composed of different parts. -
Page 18: Ce Declaration
7.1 -CE DECLARATION EC Conformity Declaration I herewith declare that the design of the Walk behind vacumised sweeper Tennant S8 complies, in the supplied version, with the requisite provisions: • 98/37/CE Machinery Directive • 73/23/CE Low Voltage Directive • 89/336/CE – 92/31/CE Electromagnetic Compatibility Directive •...