Duratrax Micro street force RTR Assembly And Operation Manual
  1. Manuals
  2. Brands
  3. Duratrax Manuals
  4. Motorized Toy Car
  5. Micro street force RTR
  6. Assembly and operation manual

Duratrax Micro street force RTR Assembly And Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Length: 8-1/8" [207mm]
Width: 4-1/8" [105mm]
Height: 2-11/16" [69mm]
Weight: 13.5oz [383g]
Wheelbase: 5-7/8" [150mm]
Radio: 2-Channel
•
DuraTrax will warranty this kit for 90 days after the purchase date from defects in materials or workmanship. DuraTrax will either repair
or replace, at no charge, the incorrectly made part.
•
Make sure you save the receipt or invoice you were given when you purchased your model. It is your proof of purchase and we must
see it before we can honor the warranty.
•
To return your Micro Street Force for repairs covered under warranty you should send your model to:
If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this
kit immediately in new and unused condition to the place of purchase.
READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT
INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.
© Copyright 2003
ASSEMBLY AND OPERATION MANUAL
3002 N. Apollo Drive Suite 1
Champaign, Illinois 61822
Attn: Service Department
Phone: (217) 398-0007 9:00 am-5:00 pm Central Time M-F
E-mail: hobbyservices@hobbico.com
®
Warranty
Hobby Services
™
Technical Support Information
For technical assistance, contact:
DuraTrax Product Support
3002 N. Apollo Drive, Suite 1
Champaign, IL 61822
(217) 398-8970, Ext. 5
carsupport@duratrax.com
DTXZ1103 For Kit DTXD10**

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Micro street force RTR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Duratrax Micro street force RTR

Summary of Contents for Duratrax Micro street force RTR

  • Page 1 ASSEMBLY AND OPERATION MANUAL Warranty • DuraTrax will warranty this kit for 90 days after the purchase date from defects in materials or workmanship. DuraTrax will either repair or replace, at no charge, the incorrectly made part. • Make sure you save the receipt or invoice you were given when you purchased your model. It is your proof of purchase and we must see it before we can honor the warranty.

  • Page 2: Table Of Contents

    • Place a mat or towel over your work surface.This will prevent INTRODUCTION parts from rolling off and will protect the work surface. Thank you for purchasing the DuraTrax Micro Street Force. • Test fit all parts before attaching them permanently. This manual contains the instruction you need to build, operate and maintain your new electric R/C vehicle.

  • Page 3: Repair Service

    Street Force repaired for a small charge by the expert at 2. Charge the included 6-cell battery with the included DuraTrax's authorized repair facility, Hobby Services, at wall charger. Connect the 6-cell NiCd battery to the the address listed on the front cover of this manual.

  • Page 4: Running The Micro Street Force

    5. Turn on the transmitter using the on/off switch (see step 9. Program the ESC. Start by centering the trim knobs on #3). The red light on the transmitter should light up. If there is the transmitter. Turn the transmitter “on” then turn the ESC no light on, turn the transmitter off and check to ensure that the “on.”...

  • Page 5: Changing Wheel Track (Width)

    CHANGING WHEELBASE (LENGTH) CHANGING WHEEL TRACK (WIDTH) TO FIT OTHER BODIES NOTE: A micro servo and optional short belt are required to run the 140mm wheelbase. Hole #1 Hole #2 1. Detach the front of the rear shock from the upper plate ball stud.
  • Page 6 NOTE: Be careful not to lose the ride height spacer 8. Remove the long belt from the diff pulley. located below the lower suspension arm. 9. Remove the outer 2x8mm screw that attaches the left (when viewed from the front) front shock to the upper 12.

  • Page 7: Assembly Guide

    ASSEMBLY GUIDE USE THIS GUIDE FOR MAINTENANCE AND ASSEMBLY OF YOUR MICRO STREET FORCE ..1 (87) 6x10mm Ball Bearing Make sure the bearings are fully seated to prevent binding...2 (D) 2x6mm S/T Screw ..1 (87) 6x10mm Ball Bearing ..1 (54) 1.5x16mm Shaft Make sure the bearings are fully seated to prevent binding.
  • Page 8 2.7mm ..1 (M) M2 Nut Use threadlock Make sure the set screw is secured onto the flat spot ..1 (85) on the shaft. 5x8mm Ball Bearing ..1 (N) 3mm Set Screw 4.5mm ..1 (M) M2 Nut...
  • Page 9 Stock Glue Optional (included) Be careful not to get any glue Add the CA Glue on the gear teeth. Make sure the gear mesh is not too tight, causing binding, or too loose, causing the gears to strip...2 ( ) 2x4mm Screw ..2 (L) 2mm Washer...
  • Page 10 ..4 (E) 2.6x8mm S/T Screw ..2 (E) 2.6x8mm S/T Screw Wheelbase 150mm Wheelbase 140mm A micro servo is required for 140mm wheelbase. The stock belt for the Micro Street Force is 150mm.
  • Page 11 ..2 (30) 2x7.5mm Shaft ..6 (G) 2x6mm S/T Plate Screw ..2 (J) 2x6mm Screw ..2 (36) 5x11mm Ball Bearing ..2 (26) 3.8mm Ball Make sure the bearings are fully seated to prevent binding...2 (G) 2x6mm S/T Plate Screw 0.2mm Front Brace (15) ...2 (46) 2x23mm Shaft...
  • Page 12 ..4 (B) 2x8mm S/T Screw ..2 (33) Spring For Wheelbase 150/140mm 21.5mm For Wheelbase 150mm 18.6mm TRANSMITTER...
  • Page 13 ..1 (G) 2x6mm S/T Plate Screw Micro Standard Servo Servo 2x30mm Shaft (45)
  • Page 14 Wheelbase 150mm Wheelbase 140mm ..2 (G) 2x6mm S/T Plate Screw ..1 (H) 2x6mm F/H Screw ..1 (B) 2x8mm S/T Screw ..3 (C) 2.6x8mm S/T Screw ..1 (26) 3.8mm Ball Belt Tensioner ..1 (K) 2x12mm Screw Wheelbase 150mm Wheelbase 140mm ..2 (E) 2.6x8mm S/T Screw ..1 (33) Spring...
  • Page 15 ..2 (G) 2x6mm Plate Screw ..2 (B) 2xmm S/T Screw Rear Front Thicker sidewall Thicker sidewall to the outside. to the outside. Rear Front Outside Outside Glue Glue Add the CA glue inside both on the rim and tire. Caution: Don't overflow the glue over the tire surface.
  • Page 16 ..6 (A) 2x6mm S/T Screw ..6 (B) 2x8mm S/T Screw...
  • Page 17 ..4 (79) ..1 (72) Nylon Strap Nylon Strap...
  • Page 18 ..4 (72) ..2 (D) 2x6mm S/T F/H Screw ..2 (A) 2x6mm S/T Screw ..2 (73) O-Ring ..2 (72)

  • Page 19: Maintenance Tips

    Universal Battery Case Use this battery box to hold the included optional "AA" battery holder. Hard Standard Shock Collar To raise the front ride height of the car, add the included shock collar as shown. Shock Collar MAINTENANCE TIPS BEFORE EACH RUN •...
  • Page 20 OTHER ITEMS AVAILABLE FROM DURATRAX DTXP4010 TX NiCd Conversion DTXP2027 Micro Carrier DTXC2377 Kwik Trak Racing Cones DTXC2458 Power Shot DTXR0140 Screwdriver Set DTXQ0100 Metric Phillips Head Screw Set...

Table of Contents