1. Manuals
  2. Brands
  3. HandyWave Manuals
  4. Adapter
  5. HandyPort-Serial HPS-120
  6. User manual

HandyWave HandyPort-Serial HPS-120 User Manual

Handywave handyport-serial wireless adapter user's manual
Hide thumbs Also See for HandyPort-Serial HPS-120:
Table of Contents

Advertisement

Quick Links

See also: User Manual
HPS-120
Wireless Solutions in your Hand
HandyPort-Serial
User's Manual
UK / Europe Office
Tel: +44 (0)8700 434040
Fax: +44 (0)8700 434045
info@omniinstruments.co.uk
www.omniinstruments.co.uk
Australia / Asia Pacific Office
Tel +61 (0)282 442 363
Fax +61 (0)294 751 278
info@omniinstruments.com.au
www.omniinstruments.com.au
USA / Canada Office
Tel +1-866-849-3441
Fax +1-866-628-8055
info@omniinstruments.net
www.omniinstruments.net

Advertisement

Table of Contents
loading

Related Manuals for HandyWave HandyPort-Serial HPS-120

Summary of Contents for HandyWave HandyPort-Serial HPS-120

  • Page 1 HPS-120 HandyPort-Serial Wireless Solutions in your Hand User’s Manual UK / Europe Office Australia / Asia Pacific Office USA / Canada Office Tel: +44 (0)8700 434040 Tel +61 (0)282 442 363 Tel +1-866-849-3441 Fax: +44 (0)8700 434045 Fax +61 (0)294 751 278 Fax +1-866-628-8055 info@omniinstruments.co.uk info@omniinstruments.com.au...

  • Page 2: Table Of Contents

    Table of Contents INTRODUCTION ........................3 1.1..........................3 EATURES 1.2...........................3 ACKAGE SPECIFICATIONS........................4 2.1...........................4 ENERAL 2.2. RS-232 I ......................5 NTERFACE 2.2.1. Pin-out .........................5 2.2.2. Signals .........................5 2.3......................5 ACTORY ETTING 2.4.........................6 ISPLAY TATUS 2.5........................6 ESET UTTON 2.5.1. Enter Configuration Mode....................6 2.5.2.

  • Page 3: Introduction

    1. Introduction Thank you for purchasing a HandyPort-Serial. The HandyPort-Serial can be used as a component in many types of systems allowing them to communicate wirelessly with other Bluetooth products such as PC-cards, laptops, handheld computers, mobile phones and other HandyPort-Serial.

  • Page 4: Specifications

    2. Specifications 2.1. General Baud Rate Up to 115.2kbps (Recommend above 2.4kbps) Supports 1.2/2.4/4.8/9.6/19.2/38.4/57.6/115.2kbps Coverage Up to 100 M Connection Point-to-Point (Remark1) Signal DCD, TxD, RxD, GND, CTS/DSR , DTR, RTS RS-232 Interface D_SUB 9 Pin Female Standard Bluetooth Specification Version 1.1 Frequency 2.400 ~ 2.4835GHz Hopping...

  • Page 5: Rs-232 Interface

    2.2. RS-232 Interface 2.2.1. Pin-out 2.2.2. Signals Pin Number Signal Direction Description Output Data Carrier Detect Output Transmitted Data Input Received Data (Remark1) N/A (Input) Option: Data Set Ready Signal Ground Output Data Terminal Ready (Remark1) Input Clear to Send Output Request to Send Input...

  • Page 6: Display Status

    2.4. Display Status The following is status LED information. OPR (Red): When HPS-120 is powered on, it is turned on or flashing. LNK (Green): When a wireless link is on, it is turned on. If HPS-120 is in the configuration mode, it will be flashing every second. 2.5.

  • Page 7: Hardware Installation

    3. Hardware Installation 3.1. Hardware Description RST Button Screw RS-232 Connector OPR LED LNK LED DC In Jack USB Cable Antenna / for Power Connector 3.2. Power Supply You can supply power to the HPS-120 as follows: Use an AC/DC converter (Output Power: +5 ~ +12Vdc / 300mA). Use a provided USB cable.

  • Page 8: Usage

    4. Usage You can change the configuration of HPS-120 using Hyper Terminal. 4.1. Hyper Terminal Settings Baud Rate: 9600 bps / Data Bit: 8 / Parity Bit: None / Stop Bit: 1 / Flow Control: None / Emulation: VT100 4.2. Configuration 4.2.1.

  • Page 9: Command Set

    4.3. Command Set 4.3.1. Command List for Local Device Item Syntax Description Remarks Connecting AAddr<Enter> remote device local remote address address wireless BD_ADDR always need to connection. be difference. 2. Baud rate BBaud Rate Change the baud rate Baud Rate - 0: 1200, 1: 2400, 2: 4800, 3: 9600, 4: 19200, 5: 38400, 6: 57600, 7: 115200...

  • Page 10: Command List For Remote Device

    4.3.2. Command List for Remote Device To change the configuration for a remote device via over-the-air, firstly you have to use a command “O” at the local device. The following are a procedure for changing configuration of remote device via over-the-air. Configure a remote device at the local device.

Table of Contents