Step 2 : Setting Up The Remote Commander - Sony SLV-SE230 Service Manual

Step 2 : Setting up the remote commander

Inserting the batteries
Insert two R6 (size AA) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Using the remote
commander
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with a
dot (•) can be used to operate your
Sony TV. If the TV does not have
the symbol near the remote
sensor, this remote commander
will not operate the TV.
To operate Set [TV] / [VIDEO] to
[VIDEO] and point at the remote sensor at the VCR
the VCR
[TV] and point at the remote sensor at the TV
a Sony TV
12 Setting up the remote commander
To
Switch to Teletext* 1
Select the sound* 2
Use FASTEXT* 1
Call up the on-screen display
1
Change the Teletext page*
Switch to/from wide mode of a Sony wide TV (For
other manufactures' wide TVs, see "Controlling
other TVs with the remote commander (SLV-
SE830N only)" below.)
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery together with an old one.
• Do not use different types of batteries together.
• Some buttons may not work with certain Sony TVs.
1
* SLV-SE830N only
2
* not available on SLV-SE430K
Controlling other TVs with the remote commander
(SLV-SE830N only)
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the following table, set the appropriate manufacturer's code
number.
1 Set [TV] / [VIDEO] at the top of the remote commander to [TV].
2 Hold down ?/1, and enter your TV's code number using the programme
number buttons. Then release ?/1.
Now you can use the following TV control buttons to control your TV:
?/1, t TV/VIDEO, programme number buttons, - (ten's digit),
PROG +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons,
(wide)*, MENU*, M / m /
* These buttons may not work with all TVs.
14 Setting up the remote commander
Remote sensor
[TV] /
[VIDEO]
1 2 3
4 5 6
7 8 9
0
Press
/ (Teletext)
AUDIO MONITOR
FASTEXT buttons
DISPLAY
c ⁄ C
(wide)
< / , *, and OK*.
DISPLAY
-
/
2 +/–
a
TV control buttons
To
Set the TV to standby mode
Select an input source: aerial in or line in
Select the TV's programme position
Adjust the volume of the TV
Switch to TV (Teletext off)*
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
To switch to wide mode, see the footnotes below this table for the applicable
code numbers.
Manufacturer Code number
Sony 01*
Akai 68
Ferguson 52
Grundig 10*
Hitachi 24
JVC 33
Loewe 45
Mivar 09, 70
NEC 66
Nokia 15, 16, 69*
1
* Press (wide) to switch the wide picture mode on or off.
* 2 Press (wide), then press 2 +/– to select the wide picture mode you want.
(wide). The menu appears on the TV screen. Then, press M/m/</, to
* 3 Press
select the wide picture you want and press OK.
Tip
• When you set your TV's code number correctly while the TV is turned on, the TV
turns off automatically.
Notes
• If you enter a new code number, the code number previously entered will be
erased.
• If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may
change. Set the appropriate code number every time you replace the batteries.
1-3
?/1
AUDIO MONITOR
t TV/VIDEO
1 2 3
Programme
4 5 6
number
7 8 9
buttons
0
PROG +/–/
c ⁄ C
FASTEXT buttons
Press
?/1
t TV/VIDEO
Programme number buttons,
-, PROG +/–
2 +/–
a (TV)
1
continued
Setting up the remote commander
Manufacturer Code number
1 , 02 Panasonic 17* 1 , 49
Philips 06* 1 , 07*
Saba 12, 13
1 , 11* 1 Samsung 22, 23
Sanyo 25
Sharp 29
Telefunken 36
Thomson 2
43*
Toshiba 38
3
Setting up the remote commander
13
1 , 08* 1
15