Sanyo VPC-X1420EXR Service Manual page 19

3-9. Factory Code Setting
1. Check the "Factory Code" display within the Setting group.
2. For U.S.A., Canada and NTSC general area
If "FC_SANYO_U" does not appear, click on the "
located on the right of the "Factory Code" display BOX and
select "FC_SANYO_U".
3. For Europe and PAL general area
If "FC_SANYO_EX" does not appear, click on the "
located on the right of the "Factory Code" display BOX and
select "FC_SANYO_EX".
3-10. Language Setting
1. Click on the " " mark located on the right of the
"Language" display BOX.
2. Select language. (Default is English.)
3. End "DscCal" and remove the camera before turning the
camera power OFF.
LCD
Calibration Upload
R Bright
AWB
Firmware
Focus
RGB Offset
Data
UV Matrix
Tint
Cal Mode
Initialize
OK
EVF VCO
H AFC
Cal Data
LCD Type
OK
USB storage
Get VID Set Serial
PID
Set
Backrush pulse :
Get
3-11. Reset Setting
Carry out reset settings after replacing CP1 board.
1. Turn on the camera.
2. Double-click on the DscCalDi.exe.
3. Select "Set Default" on the LCD "Test".
3-12. The Compulsive boot starting method
1. Keep SET button and SHUTTER button depressed while
switching on the power.
2. Connect the camera and the computer with USB cable.
" mark
" mark
B Bright VCOMDC
Gain VCOMPP
Phase
Hall Cal.
Test
Setting
Language
Set
Video Mode
Set Rev. Set
Factory Code
Set
3-13. Firmware uploading procedure
1. Uploading the firmware should be carried out if the version
number (COMPL PWB XX-X) on the replacement circuit
board is lower than the version of the distributed firmware.
For XX-X, enter the name of the circuit board containing the
firmware.
2. The firmware is distributed by e-mail in self-extracting archive
format. Change the extension of the distributed file to .EXE
and save it in your preferred folder.
3. When you double-click the saved file, the firmware (binary
file) will be saved in the same folder.
4. The firmware must not be distributed without permission.
1. Overwriting firmware from the SD card
Preparation:
SD card: SD card with firmware rewritten into the root direc-
tory
Data: S41BNxxx.BIN (xxx: version)
Overwriting method:
1. Insert the above SD card.
2. Turn on the camera.
3. The play button is pushed for 2 seconds and PLAY mode is
desplayed.
4. Press the MENU button.
5. Choose the OPTION MENU.
6. Choose the FORMAT.
7. Toggle the SET button to the left for 2 seconds. FIRMWARE
UPDATE will display.
8. Choose YES.
9. Press the SET button. Update is starting.
Note:
Do not turn off the camera's power or remove the SD card
while the firmware is being updated.
The power will turn off after the update is complete.
2. Overwriting firmware from the calibration software
Preparation:
PC with overwriting firmware copied to the preferred folder in
the HD.
Data: S41BNxxx.BIN (xxx: version)
Overwriting method:
1. Connect the camera's USB/AV terminal to the computer'
USB connector.
2. The USB Connection screen appears on the camera's LCD
monitor. Choose the "COMPUTER", and press the SET
button. Next, choose the "CARD READER", and press the
SET button.
3. Double-click on the DscCalDi.exe.
4. Click the Firmware.
5. Choose the fimware file to use for overwriting, and click
the Yes.
6. Update is starting. The message will appear, and choose
OK.
7. After the update is complete, disconnect the USB cable
and turn the camera's power off.
Note:
Do not turn off the camera's power while the firmware is be-
ing updated.
– 19 –