Copyright 2006 All rights Reserved Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit.
For Your Protection L Thoroughly read and understand the “Safety Label” section, read all instructions noted on them. PR2572 & PR2596 Powered Rakes 314-132M WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed.
Page 4
L Never allow children to operate equipment. PR2572 & PR2596 Powered Rakes 314-132M Table of Contents Transport Machinery Safely L Comply with state and local laws. L Maximum transport speed for implement is 20 mph.
L Avoid the hazard by relieving L Use a piece of paper or L Wear protective gloves and safety L If an accident occurs, see a PR2572 & PR2596 Powered Rakes 314-132M should be worn. appropriate for the job. Avoid loose fitting clothing.
Keep all safety labels clean and legible. Replace all damaged or missing labels. To order new labels go to your nearest Land Pride dealer or visit our dealer locator at landpride.com. Some new equipment installed during repair requires safety labels to be affixed to the replaced component as PR2572 &...
Page 7
Land Pride Important Safety Information 6/06/06 Table of Contents 15810 15813 15810 PR2572 & PR2596 Powered Rakes 314-132M KEEP AWAY 818-254C Danger: Rotating Roller Hazard (Both Sides) 818-255C Warning: General Safety 818-540C Danger: Guard Missing...
Page 8
Important Safety Information PR2572 & PR2596 Powered Rakes 314-132M Table of Contents 15811 ROTATING DRIVELINE KEEP AWAY! 15811 10592 Land Pride 818-540C Danger: Guard Missing 818-552C Danger: Rotating Driveline 838-094C Warning: Hydraulic Pressure 6/06/06...
Land Pride Introduction Introduction Land Pride welcomes you to the growing family of new product owners. This implement has been designed with care and built by skilled workers using quality materials. Proper assembly, maintenance, and safe operating practices will help you get years of satisfactory use from the machine.
Tractor Requirements This powered rake is designed with a 3-Point category I hitch. Horse power rating of tractor should not exceed 50 PTO horse power on all PR2572 & PR2596 Powered Rakes. IMPORTANT: In order to maintain steering control, ballast may have to be added to the front end of your tractor.
(#8) and 1/2” nuts (9). 7. Install the bottom tine lift arms (#12) to the tine frame (#2) and secure with the 1” flatwashers (#5) and cotter pins (#6). Tines and Tine Frame Assembly Figure 1-3 PR2572 & PR2596 Powered Rakes 314-132M...
Page 12
Table of Contents Land Pride Section 1: Assembly & Set-up 10666 Lift Arm Location and Hose Routing Figure 1-4 10666 Tine Locations and Alignment Figure 1-5 PR2572 & PR2596 Powered Rakes 314-132M 6/06/06...
Round off all sharp edges and remove burrs. Grease sliding profiles. PR2572 & PR2596 Powered Rakes 314-132M Table of Contents Prior to initial operation and after long periods of inactivity, the Friction Clutch should be “run-in”. Refer to 1.
PTO, turning off tractor, and removing ignition key 14. The danish tine package option loosens rocks and trash below the surface of the ground. Normal operating depth is 1" to 4" deep when needed. PR2572 & PR2596 Powered Rakes 314-132M...
If the PR2572 & PR2596 Powered Rakes 314-132M Table of Contents powered rake is too high in the front then the rear portion of the roller will cut deeper than the front portion of the roller when angled.
(#4) and moving the material control blade front to rear in the slot (#5). Normally the dimension “A” should be close to 1 3/4”. 11539 Material Control Blade Adjustment Figure 3-2 PR2572 & PR2596 Powered Rakes 314-132M...
After using your Rotary Cutter for several hours, check all bolts to be sure they are tight. Replace any worn, damaged or illegible safety labels by obtaining new labels from your Land Pride Dealer. CAUTION BEFORE any maintenance is preformed, lower the power rake to the ground, stop tractor engine and remove key.
Figure 5-2 and Figure 5-3. Top Bearing Seal Location Figure 5-2 Bottom Bearing Seal Location Figure 5-3 PR2572 & PR2596 Powered Rakes 314-132M Table of Contents Friction Clutch PTO Refer to Figure 5-4: Powered Rake drive components are protected from shock loads by a two plate friction clutch located between the gearbox and the drive shaft.
Inspect friction disks and hub. 10435 6/06/06 Table of Contents Assembly 10449 PR2572 & PR2596 Powered Rakes 314-132M Step 1 Place the hub and friction disks into the housing. Step 2 Compress the Belleville Springs to the pressure plate by tightening the four hex nuts and then placing the assembly into the clutch housing.
Type of Lubrication: Multi-Purpose Grease Gauge Wheel Spindle Type of Lubrication: Multi-Purpose Grease Gauge Wheel Type of Lubrication: Multi-Purpose Grease Drive Chain Type of Lubrication: Multi-Purpose Grease Oil Level Plug PR2572 & PR2596 Powered Rakes 314-132M Required Required Required Required...
2190 4820 3560 mm x pitch = nominal thread diameter in millimeters x Tire Inflation Chart TireSize Inflation PR2572 & PR2596 Powered Rakes 314-132M Bolt Head Identification 10.9 Class 5.8 Class 8.8 Class 10.9 l215 1050 1150...