Orbit Timer Quick Start Manual

2. mount timer
TIMEr
quICk STArT guIDE
4.17"
(106mm)
PROGRAM
RAIN DELAY
RESET
3 dimensions:
proof no:
AUTO fl at: w: 9"
Use included mounting template to date: 10.05.07 fi nished: w 9"
des: SM spck: SM colors
job no:
mark screw locations. 07WTM005259
client: Orbit Registration
sku: 57880 K
p 801 295 9820 upc: ? ????? ????? ?
f 801 951 5815 additional instructions:
www.fl uid-studio.net fi le name: 07WTM005259 ·
1065 South 500 West 57880-04 rA.indd ·
Bountiful, Utah 84010 software: Illustrator CS2
rEquIrED TOOlS:
Phillips Screwdriver
Wire Strippers
Keyhole
Note: The quick start guide is intended to help you
get up and running with your new timer. It includes
basic installation and programming help. For more
detailed and advanced instruction, please download
the full manual "Outdoor Swing Panel Timer" at
www.orbitonline.com
PN 57896-50 rE
1. Select location
Pre-formed
Indoor mounting holes
AUTO
Hang timer on screw using keyhole.
Clean, dry, and out of direct sunlight
Allow 9 inch clearance for the swing door
. Or
. . .
.
.
.
. . . .
.
.
. .
. . .
. Outdoor . .
.
.
. . .
. . . .
Screw through one of the
pre-formed mounting holes.
.
For detailed instructions on outdoor wiring, please download the
full manual "Outdoor Swing Panel Timer" at www.orbitonline.com
Warning: Check state and local codes. Orbit recommends using
a licensed electrical contractor for outdoor wiring of timer.
3. connect SPrinkler
valveS to timer wireS
Common Wire
To
Wire Nut
Timer
MOUNTING TEMPLATE
GABARIT D`INSTALLATION
GUIA DE COLGAR
Solenoid
Printers are responsible for Valve
h: 7" meeting print production
d: 0" h 7" requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
crop color color designated specifi cations
non printing non printing on this form.
PMS PMS
PMS ???? ???? ???? © 2007 Fluid Studio. This
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.
Connect one of the two wires from each valve to the
common wire leading to the timer (usually white).
Connect the other wire from each valve to one of the
colored wires leading to the timer.
1/8"
4. connect valve wire
No. 8 Screw
to terminal
Do not connect to power
source until after wiring
Wall valves to timer
Only connect one valve to
each terminal (station)
Station 1 RESET
Strip wire
Push in
AUTO
Level
Push tab
upward to
release wire
5. connect to
electrical Power
Reset
Indoor
RESET
B
E
AUTO
A
Outdoor
PROGRAM
RAIN DELAY Indicator
RESET
AUTO
.
Button Function:
A EntEr - to confirm a new setting
Warning: See manual for outdoor wiring instructions
MAnuAl - to water manually
ClEAr - to clear a setting
B
6. activate Battery
proGrAM - to switch between
C
programs - A, B, and C
D ArroW [ ] - to skip to the next
setting / watering station or move to
other programs/settings
ArroW [ ] - to go back to the
E
previous setting / watering station or
Remove plastic
move to other programs/settings
PROGRAM strip to activate
battery
F rAin DElAy - to pause operation
RAIN DELAY
for 24-72 hours due to rain or other
factors
[+] - to increase a numeric setting
G
[ - ] - to decrease a numeric setting
H
Dial Position Function:
i Auto - Watering mode
J SEt CloCK - Set calendar and clock time
SEt DAtE - year, Month, and Day
K
One Lithium CR2032 battery (included) is required StArt tiME - Set time to begin watering
l
to retain the program in memory during power loss.
Annual replacement is recommended.
M run tiME - Set watering duration for
each station
Remove the plastic strip to activate the
pre-installed battery.
HoW oFtEn - Set frequency of
n
watering days
BuDGEt - Adjust overall watering as
o
a percentage
p oFF - turn all stations off
2
dimensions:
proof no: Printers are responsible for
flat: w: 32" h: 14" meeting print production
date: 09.14.12 finished: w 32" d: " h 14" requirements. Any changes
must be approved by the
colors
des: SM client and Fluid Studio.
printed piece must meet
fold color color
client: Orbit Registration non printing non printing designated specifications
on this form.
sku: PMS PMS
57896 PMS
K ???? ???? ???? © 2012 Fluid Studio. This
work is the property of Fluid
p 801 295 9820 upc: NA
f 801 951 5815 additional instructions: Studio, and cannot be used,
· Proofing Code: reproduced or distributed
www.fluid-studio.net file name: 57896-50 rE.indd
· in any way without their
1065 South 500 West
·
software: InDesign CS5 express permission.
Bountiful, Utah 84010
8. aDDitional FeatureS
7. Program timer
Set Current Time
A
Battery
(e.g. pacific,
rain Delay
mountain standard)
C
PROGRAM
F
RAIN DELAY
Turn dial to set clock enter current time (+/-)
• Turn dial to AUTO and Press the [RAIN DELAY] button.
G
• Push the [+/-] to select 24, 48 or 72 hours.
• Press [ENTER] to begin.
Set Date
B
D
Press [CLEAR] to cancel the rain delay.
manual watering
H
SET
DATE
Your timer has the ability to allow you to manually water without
disturbing the preset program.
Swing
Out Panel
• Turn dial to SET DATE to enter the Year, Month and Day.
Release
• Use the (+/-) button to select the Year.
• Press [ENTER] to advance to Month and Day.
Set Start Time
C
Time to begin To run all stations at the pre-programed duration
watering • Turn the dial to AUTO.
• Press the [MANUAL] button. Display will show A B and ALL.
• Press [ENTER] (or wait a few seconds) to begin manual watering.
All stations will water consecutively for their programmed duration.
To run a specific station for specified time
• Turn the dial to AUTO.
• Press the [MANUAL] button.
• Turn dial to START TIME position.
• Press [ENTER].
• Enter one start time using the (+/-) button.
• Press the [ / ] buttons until desired station number appears.
• Press the [ENTER] button to save.
• Press the [+/–] to enter the desired duration.
Note: Additional start times – Additional start times can be
• Press [ENTER] (or wait a few seconds) to begin manual watering.
entered if you want your sprinklers to water the same area
multiple times a day. For instructions please download the
To stop Manual Watering press [CLEAR].
"Outdoor Swing Panel Timer" manual at www.orbitonline.com.
note: After the [MANUAL] button has been pushed, if a selection
is not made within 5 seconds all stations and programs will begin
watering using the programmed RUN TIMES. If no RUN TIMES have
Select Watering Duration
D
been set, nothing will happen and the display will return to the time
Set for each station
of day.
then press enter
BackuP Battery
Your timer requires a CR2032 Lithium battery to maintain your
program in case of an AC power loss.
tip: The Battery should be replaced every year, to avoid loss of
programming.
Turn dial to run time enter the watering duration (+/- ) for each
station ([ENTER] or [ARROW] to move between stations). note: A battery alone will not operate the valves in your sprinkling
system. The sprinkler timer transformer must be connected to an
AC line voltage source.
E Set Watering Days
For instructions on "Water Budgeting", connecting the timer to a
or Interval
"Pump Start" relay, replacing the "Backup Battery" or for installing
your timer outdoor, please download the full manual "Outdoor
Swing Panel Timer" at www.orbitonline.com
Turn dial to how often to select watering days ([ARROWS]
to move and [ENTER] to select).
To water on Odd or Even days or to water using Intervals
days, please download the full manual "Outdoor Swing
Panel Timer" (at www.orbitonline.com) for instructions.
F Set Auto Mode
Turn dial to AUTO—you have programmed your timer!
helP
1-800-488-6156 or 1-801-299-5555
www.orbitonline.com
Before returning this sprinkler timer to the store, contact Orbit
®
Technical Service at: 1-800-488-6156, 1-801-299-5555.
liStingS
The sprinkler timer is tested to UL60730 standard & is ETL listed.
®
Appropriate international models are CSA ® and CE ® approved.
This Class B digital apparatus complies with Canadian ICES-003.
Disconnection : Type 1Y
Input: 120V, 60Hz, 0.2A; Output: 26V, SOOmA
Rated impulse voltage: 2500V
Pollution degree: 2
The supply cord of this control can be replaced only by the
manufacturer or his accredited service agent.
traDemark notice
WaterMaster is a registered trademark of Orbit Irrigation
® ®
Products, Inc. The information in this manual is primarily intended
for the user who will establish a watering schedule and enter that
schedule into the sprinkler timer. This product is intended to be
used as an automatic sprinkler timer for activating 24 VAC irrigation
valves, as described in this manual.
warranty anD Statement
Orbit ® Irrigation Products, Inc. warrants to its customers that its
products will be free from defects in materials and workmanship
for a period of six years from the date of purchase.
We will replace, free of charge, the defective part or parts found to
be defective under normal use and service for a period of up to six
years after purchase (proof of purchase required).
We reserve the right to inspect the defective part prior to
replacement.
Orbit ® Irrigation Products, Inc. will not be responsible for
consequential or incidental cost or damage caused by the product
failure. Orbit liability under this warranty is limited solely to the
®
replacement or repair of defective parts.
To exercise your warranty, return the unit to your dealer with a copy
of the sales receipt.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user's authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: This appliance is not intended for use by young children
or infirm persons without supervision. Young children should be
supervised to ensure that they do not play with the appliance.