1. Manuals
  2. Brands
  3. PSA Manuals
  4. Smoke Alarm
  5. Lifesaver HA240
  6. Installation and user manual

PSA Lifesaver HA240 Installation And User Manual

Heat alarm psa lifesaver ha240
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
1004-7201-01(HA240)_V2:_
MODEL HA240
FIXED TEMPERATURE DESIGN HEAT ALARM
IMPORTANT! READ ALL INSTRUCTIONS BEFORE INSTALLATION AND
SAVE THIS MANUAL FOR FUTURE REFERENCE.
WARNING! THIS HEAT ALARM IS NOT DESIGNED AS AN EARLY WARNING
TO A FIRE BECAUSE IT DOES NOT DETECT SMOKE.
SEE LIMITATIONS OF THE HEAT ALARM IN SECTION 12 FOR
DETAILS
WARNING! REMOVAL OF HEAT ALARM BATTERY AND DISCONNECTING
OR LOSS OF AC POWER WILL RENDER THIS UNIT INOPERA-
TIVE.
DO NOT TRY TO REPAIR THIS HEAT ALARM YOURSELF.
REFER TO INSTRUCTIONS IN SECTION 4 FOR MAINTENANCE.
CONTENTS
1.
SPECIFICATIONS
2.
3.
4.
5.
6.
7.
8.
9.
12. LIMITATIONS OF HEAT ALARMS
1. SPECIFICATIONS
240Vac 50Hz, 80mA max, 9V long life battery back up, single and or multiple station (24 units maximum).
The heat alarm is designed to activate at 73°C when the temperature range is between 58°C and 88°C.
Temperature rating -------------------- 73°C (163.4°F) Fixed temperature only
Maximum ambient -------------------- 88°C (190.4°F) temperature at heat alarm
Recommended coverage ---------------- 230 square metres (Note "A")
Recommended spacing -------------------15.3 metres
Maximum distance from wall ----------------- 7.6 metres (Note "B")
Note A: Maximum coverage is based on providing equal response time as sprinkler devices spaced at 3.0 metre
intervals (9.4 square metres) on a smooth ceiling approximately 4.6 metres high.
Higher ceilings may adversely affect response time and earlier response time may be obtained by
reducing the spacing between alarms.
Note B: Maximum distance is from any wall or ceiling projection extending down more than 30cm.
ELECTRICAL RATING: 240Vac, 50Hz, 80mA max per alarm with 24 alarms interconnected.
Interconnect compatible with smoke alarms of Models LIFESAVER LIF5000, LIF5800, LIF5800RL and
Lifesaver Visual Signalling Device SL240 And LANSON 240I, Isolation Relay LIFRK10A/9.
This Heat Alarm must only be wired to a 240Vac 50Hz sine wave current supply.
2010.9.2
9:20 AM
Page 1
INSTALLATION AND USER MANUAL
1

Advertisement

Table of Contents
loading

Related Manuals for PSA Lifesaver HA240

Summary of Contents for PSA Lifesaver HA240

  • Page 1: Table Of Contents

    1004-7201-01(HA240)_V2:_ 2010.9.2 9:20 AM Page 1 MODEL HA240 FIXED TEMPERATURE DESIGN HEAT ALARM INSTALLATION AND USER MANUAL IMPORTANT! READ ALL INSTRUCTIONS BEFORE INSTALLATION AND SAVE THIS MANUAL FOR FUTURE REFERENCE. WARNING! THIS HEAT ALARM IS NOT DESIGNED AS AN EARLY WARNING TO A FIRE BECAUSE IT DOES NOT DETECT SMOKE.

  • Page 2: Recommended Locations Of Alarms

    PSA advises that additional detec- tion devices, installed within rooms, may be necessary.

  • Page 3: Locations To Avoid

    1004-7201-01(HA240)_V2:_ 2010.9.2 9:20 AM Page 3 2.6: In rooms with open joists or beams,all ceiling mounted alarms shall be located on the bottom of such beams. (See diagram “C”) 2.7: Alarms installed on an open-joist ceiling shall have the smooth ceiling spacing reduced to no more than half of the listed spacing when measured at right angles to the solid joist.

  • Page 4: Mounting Instructions

    1004-7201-01(HA240)_V2:_ 2010.9.2 9:20 AM Page 4 The maximum wire run distance between the first and last unit in an interconnected system is 307 metres. Figure 1 illustrates interconnection wiring. Improper connection will result in damage to the alarm, failure to operate, or electrical shock hazard. Make certain alarms are wired to a continuous (non-switched) final sub-circuit.

  • Page 5: Installing The Base Plate

    1004-7201-01(HA240)_V2:_ 2010.9.2 9:20 AM Page 5 7. INSTALLING THE BASE PLATE CONNECTOR SQUEEZE LOCKING ARMS AND PULL MARKS TAMPER RESIST LOCKING PIN REMOVE INSTALL FIGUE 5 FIGURE. 3 FIGURE. 4 After installation TEST your alarm by pressing and holding the test button for several seconds. You can also use a hand held hair dryer to test your heat alarm.

  • Page 6: 10. Maintenance

    1004-7201-01(HA240)_V2:_ 2010.9.2 9:20 AM Page 6 10. MAINTENANCE 10.1: ALARM REMOVAL: Turn off the AC power supply to the heat alarm at the main distribution board. To replace the battery remove the alarm from the trim ring by rotating the alarm in the direction of the TURN TO REMOVE arrow on the cover (see Section 7 fig.4 and Section 10.2 fig 5).

  • Page 7: 13. Good Safety Habits

    16.1 PSA Products Pty Ltd warrants that for two years from the date of purchase of the Heat Alarm, it will re- pair or replace the Heat Alarm (at the option of PSA Products Pty Ltd) due to any manufacturing defect, at the cost of PSA Products Pty Ltd (excluding any labour costs relating to removal or re-installation of product, and transport costs).
  • Page 8 1004-7201-01(HA240)_V2:_ 2010.9.2 9:20 AM Page 8 AUSTRALIAN ELECTRICAL AUTHORITY - CS:SGSE/100434 Another Quality Product By: PSA Products Pty Ltd 17 Millicent Street, Burwood 3125 Victoria, Australia Telephone : (03) 9888 9889 Facsimile: (03) 9888 9993 E-mail: enquiry@psaproducts.com.au Website: http://www.psaproducts.com.au N10116...

Table of Contents