Table of Contents
Related Manuals for PSA LIFESAVER LIFPE10LP
Summary of Contents for PSA LIFESAVER LIFPE10LP
- Page 1 Low Profile Photoelectric Smoke Alarm Model LIFPE10LP Lithium (non-replaceable sealed in) Battery-Operated Photoelectric Smoke Alarm. Designed with style in mind, this smoke alarm has a slim line profile while providing maximum protection.
-
Page 2: Product Description
Thank you for purchasing this PSA LIFESAVER smoke alarm! Please read these instructions carefully and store them in a safe place where you can access them easily. Product description This alarm detects particles of combustion using photoelectric technology. This smoke alarm has an expected service life of ten years under normal conditions. -
Page 3: Product Specifications
Product Specifications Detection method Photo-electric Technology Power supply Sealed battery (3V DC) Battery spec CR123A Battery lifetime 10 years Alarm volume ≥ 85 dB (A) at 3 meters Operating temperature 0 °C - 40 °C Operating humidity < 93 % Date of replacement See product label Individual alarm indicator... -
Page 4: Where To Install A Smoke Alarm
Each State or Territory may differ in building codes and regulations. PSA Products can only recommend the locations. • Locate an alarm for each separate sleeping area in the immediate vicinity of the bedrooms. Try to monitor the exit path as the bedrooms are usually farthest from an exit. - Page 5 • Locate an alarm in every room where a smoker sleeps. • Locate an alarm in every room where electrical appliances are operated (i.e. portable heaters or humidifiers). • Locate an alarm in every room where someone sleeps with the door closed. The closed door may prevent an alarm not located in that room from waking the sleeper.
- Page 6 Location of smoke alarm Apex Of Sloping Ceiling Ceiling / Wall Junction Typical Multiple Floor Single Floor Installation...
-
Page 7: Where Not To Install A Smoke Alarm
Where not to install a smoke alarm • Do not locate your smoke alarm in the garage - products of combustion are present when you start your automobile. Use Lifesaver Heat Alarm in this location. • Do not locate your smoke alarm in front of forced air supply ducts used for heating and air conditioning and other high air flow areas. - Page 8 Activation Before commissioning the smoke alarm, it is important to activate it and test it for correct operation. • Install the smoke alarm onto the mounting bracket. The smoke alarm will give a short beep when the alarm is fully connected to the bracket. •...
- Page 9 • Place the smoke alarm on the mounting bracket and secure it by turning it clockwise. Test the correct operation of your smoke alarm by pressing the test button. • If no sound is generated, the smoke alarm is not functioning properly and should not be used! Alarm silence facility...
-
Page 10: Low Battery Mode
Low battery mode When the battery is running low, the smoke alarm will indicate this with a repetitive beep and flash for approximately 30 days. WARNING: This smoke alarm is equipped with a non- replaceable battery. When this warning occurs, replace the device as soon as possible! The low battery warning beep can be hushed for 10 hours by pressing the test/hush button. - Page 11 Alarm Tamper-Resist Feature A tamper resist feature has been provided. To activate this feature, you must break out the tamper- resist blocks on the mounting plate. Using this feature will deter children and others from removing the alarm from the mounting plate. Disassembling To disassemble the smoke alarm, take a screw driver and push it into the mounting hole.
-
Page 12: Maintenance
Maintenance • This smoke alarm is equipped with a self-testing mechanism. We recommend to test the smoke detector manually at least once every three months by using the test facility. If the smoke alarm functions correctly, it will generate a loud beep. Due to the loudness of the alarm, make sure that you always stand at arm’s length distance from the unit when you are testing. -
Page 13: Product Warranty Registration
Product warranty registration Thank you for purchasing and installing the most trusted brand in fire, security and intercoms. To ensure you receive excellent after-sale product service we encourage you to register your products. There are a few important reasons to register your product: It will ensure your investment is protected in case it is damaged or broken and we can effectively carry out any warranty claims. - Page 14 Overview visual & acoustic signals Operating Visual signal Acoustic signal Description mode (flash) (beep) mode Device is 1 x per Normal None functioning 40 second properly 1 x per second 1 x per seconds Test (3 x) / pause (3 x) / pause Device is tested of 1.5 seconds of 1.5 seconds...
-
Page 15: Warranty And Liability
Warranty and Liability PSA Products Pty Ltd (ABN: 99 076 468 703) of 17 Millicent Street, Burwood 3125 Victoria, Australia warrants the model LIFPE10LP for a period of five (5) years from the date of purchase, as reflected on the Authorised Reseller’s or Distributor’... - Page 16 4. To the extent permitted by law, PSA Products Pty Ltd., makes no warranty, expressed or implied, written or oral, including that of merchantability or fitness for any particular purpose, with respect to the consumer replaceable battery if any. A product with non-serviceable built-in battery is covered under warranty of the product.
Need help?
Do you have a question about the LIFESAVER LIFPE10LP and is the answer not in the manual?
Questions and answers