Related Manuals for ActForNet LEGUANG N900
Summary of Contents for ActForNet LEGUANG N900
- Page 1 LEGUANG N900 Wireless Router Configuration Guide ActForNet Technologies Inc. February 2014...
-
Page 2: Table Of Contents
LEGUANG N900 Configuration Guide Contents What is included ..........................3 Installation Guide ..........................3 How to connect ........................... 3 How to reset ..........................4 How to configure your PC to set up the bridge ..............4 Login to the wireless router ....................... 5 Wireless Router Configuration ...................... -
Page 3: What Is Included
LEGUANG N900 Configuration Guide 1. What is included 2. Installation Guide How to connect N900 comes with 2 network ports, one of which (beside the four LEDs) is intended to connect local PC or switches and the other is intended to connect service provider to upper level router. -
Page 4: How To Reset
LEGUANG N900 Configuration Guide How to reset In some cases, you may need to factory reset the system. For example, you forget your password. After the system has boot up which takes about 1 minute, press the RESET button which is located between the power supply plug and LEDs(see diagram above) for around 15 seconds before release it, the system will be reset after reboot with default configuration. -
Page 5: Login To The Wireless Router
LEGUANG N900 Configuration Guide Login to the wireless router The factory default IP address: 192.168.1.1 Default username: admin Default password: admin Open your browser and type the default IP into the address field, and enter the default user credential as prompted, you should be able access the admin GUI of the wireless router. -
Page 6: Wireless Router Configuration
LEGUANG N900 Configuration Guide 3. Wireless Router Configuration Wireless Router Operating Modes LEGUANG N900 supports three operation modes: Gateway Mode: In this mode, the device works as a router, connecting to Internet with WAN port via ADSL/Cable Modem. Local PCs are connected to the router with LAN port or WiFi. -
Page 7: Gateway Mode Configuration
LEGUANG N900 Configuration Guide Gateway Mode configuration 1. Gateway mode is the default operating mode. If you are running a brand new system, you don’t have to make any change to be in this mode. Otherwise you can switch to Gateway mode on operation mode page as following: 2. - Page 8 LEGUANG N900 Configuration Guide 3. Configure WAN settings WAN is the port that connects to the service providers and it has to be configured to access the Internet. Wireless router supports Dynamic IP, PPPoE, Static IP or PPTP. Pick the appropriate the settings according to the service provider requirement.
- Page 9 LEGUANG N900 Configuration Guide At a minimum, you need to configure the SSID(network name), region, authentication scheme and the key. After you click apply, the system will take a few seconds to make the new settings take effect: In some cases, you may want to set up virtual access point to separate the wireless network.
-
Page 10: Bridge Mode Configuration
LEGUANG N900 Configuration Guide 5. Now you should be able to see the wireless network you just configured from your PC or tablet, smart phones, etc. Click the network and supply the password/key you just configured to access the network. - Page 11 LEGUANG N900 Configuration Guide Please OK and wait for the system to come back after reboot. 2. After the system switches to bridge mode, the GUI will be a bit different because some settings like WAN and Firewall are not applicable in bridge mode.
- Page 12 LEGUANG N900 Configuration Guide 4. Wireless settings Wireless settings in bridge mode is no difference than Gateway mode. At a minimum, you need to configure the SSID(network name), region, authentication scheme and the key. After you click apply, the system will take a few seconds to make the new settings take effect:...
-
Page 13: Wireless Isp Mode
LEGUANG N900 Configuration Guide In some cases, you may want to set up virtual access point to separate the wireless network. N900 supports up to 2 virtual access points. Click “Virtual AP”, supply the SSID, authentication scheme and key and then click “add”. After you click “Apply”, the system will reboot with newly added virtual access points: 5. - Page 14 LEGUANG N900 Configuration Guide Please OK and wait for the system to come back after reboot. 2. Wireless client setting In wireless ISP mode, the wireless router acts as a wireless client to the access point of the service provider. Click “Connect Setting” that leads to the connection setting page where all the wireless client related settings are configured.
- Page 15 LEGUANG N900 Configuration Guide After you select the AP from the list, the Authentication field will be auto-populated accordingly. You just need to type in the password that is supplied by your service provider. After you click “Apply”, the system will reboot to make the change take effect. If the setting...
- Page 16 LEGUANG N900 Configuration Guide default and all the PCs on the local network will share the WAN IP address to access Internet. In most case the default setting “dynamic IP” should work. But we can change it to static IP or PPPoE as well if needed.
- Page 17 LEGUANG N900 Configuration Guide and the key. After you click apply, the system will take a few seconds to make the new settings take effect: In some cases, you may want to set up virtual access point to separate the wireless network.
- Page 18 LEGUANG N900 Configuration Guide 6. Now you should be able to see the wireless network you just configured from your PC or tablet, smart phones, etc. Click the network and supply the password/key you just configured to access the network. After the wireless connection is up, you should be able to access Internet.