Page 1
Please use this service manual with referring to the operating instructions without fail. Some illustrations using in this service manual are slightly different from the actual set. u163 Denon Brand Company, D&M Holdings lnc. X0360 V.04 DE/CDM 0712 http://www.xiaoyu163.com...
Page 2
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
Page 4
http://www.xiaoyu163.com S-52/S-52DAB/S-32 WIRE ARRANGEMENT 3 7 63 1515 0 If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation.
Page 5
http://www.xiaoyu163.com S-52/S-52DAB/S-32 2. SIDE BRACKET(R) 3 7 63 1515 0 Fasten the CY091 9P PH- PH SHIELD CORD on the H/P PORTBLE IN UNIT to the SIDE BRACKET (R) with a cord holder 3. SIDE BRACKET(L) L 13942296513 Fasten the CY051 5P PH- PH CON. CORD on the USB TERM.
Page 6
http://www.xiaoyu163.com S-52/S-52DAB/S-32 4. FERRITE CLAMP102010N 3 7 63 1515 0 Coil and lock the primary side code of the power transformer with FERRITE CLAMP opened, then paste the EMIFILTER CUSHION to outer. Fasten the FERRITE CLAMP to the EMIFILTER CUSHION with a clamp band .
Page 7
http://www.xiaoyu163.com S-52/S-52DAB/S-32 DISASSEMBLY 3 7 63 1515 0 (Follow the procedure below in reverse order when reassem- bling.) 1. BOTTOM COVER & SPEAKER BLOCK (1) Remove the 2 screws 107 on the bottom side. (2) Detach the COVER PLATE in the direction of the arrow. (3) Disconnect the 4P VH CON.CORD from the [CY042] on the POWER AMP UNIT.
Page 8
http://www.xiaoyu163.com S-52/S-52DAB/S-32 2. SPEAKER UNIT 3 7 63 1515 0 (1) Remove the 4 screws 109 fixing the SPEAKER BOX. (Both left and right) (2) Remove the wire soldered to the SPEAKER terminal. (Both left and right) (3) Remove the 4 screws 112 fixing the speaker, then detach the SPEAKER in the direction of the arrow.(Both left and right) L 13942296513...
Page 9
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3A.CD MECHA BLOCK(S-52) 3 7 63 1515 0 (1) Remove the 7 screws 105 and the 1 screw 104. (2) Remove the 4 screws 104. (3) Disconnect the 9P PH-PH SHIELD CORD from the CY091 on the H/P PORTABLE IN UNIT. (4) Disconnect the 5P PH-PH CON.CORD from the CY051 on the USB TERM.
Page 10
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 (5) Disconnect the 9P/5P PH-PH CON.CORD in the direc- tion of each the arrow. (6) Lift up the CD MECHA BLOCK as shown in the photo and disconnect the 30P FFC(1.0) from the the [CX151] on the MAIN UNIT.
Page 11
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3B.MAIN CHASSIS(S-32) 3 7 63 1515 0 (1) Remove the 8 screws 105. (2) Remove the 2 screws 104. (3) Disconnect the 9P PH-PH SHIELD CORD from the CY091 on the H/P PORTABLE IN UNIT. 9P PH-PH SHIELD CORD L 13942296513 u163 http://www.xiaoyu163.com...
Page 12
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 (4) Disconnect the 9P PH-PH SHIELD CORD in the direction of the arrow A. (5) Disconnect the MAIN CHASSIS in the direction of the ar- row B. MAIN CHASSIS L 13942296513 u163 http://www.xiaoyu163.com...
Page 13
http://www.xiaoyu163.com S-52/S-52DAB/S-32 4. 1U-3851 CD ROM UNIT(S-52) 3 7 63 1515 0 (1) Remove each 2 screws D and E, then detach the MAIN CHASSIS and the MECHA BRACKET in the direction of the arrow. MAIN CHASSIS & MECHA BRACKET (2) Move the Pick Up to the rear side and solder the short- circuit, then disconnect the FFC.
Page 14
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 (3) Disconnect the 2P, 3P, 4P Wire and the FFC, then re- move the 2 screws E. 3P Wire 4P Wire 2P Wire (4) Stand the CD ROM UNIT and disconnect the FFC. L 13942296513 u163 http://www.xiaoyu163.com...
Page 15
http://www.xiaoyu163.com S-52/S-52DAB/S-32 5. MAIN BLOCK 3 7 63 1515 0 (1) Remove the 5 screws 106 and the 5 screws 108 on the rear. (2) Disconnect the 10P ZH-JB CON.CORD from the [CX101] on the MAIN UNIT. (3) Disconnect the 13P PH-PH SHIELD CORD from the [CX131] on the MAIN UNIT.
Page 16
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 (4) Disconnect the 16P FPC from the [CX161] on the MAIN UNIT. (5) Disconnect the 6P ZH-ZH CON.CORD from the [CX064] the MAIN UNIT. 16P FPC 6P ZH-ZH CON. CORD (6) Detach the MAIN BLOCK in the direction of the arrow. L 13942296513 u163 http://www.xiaoyu163.com...
Page 17
http://www.xiaoyu163.com S-52/S-52DAB/S-32 6A. 1U-3854 STANDBY TRANS UNIT 3 7 63 1515 0 (for JP/E3/E2) Remove the 1 screw 113 and the 1 screw 105 on the rear. (2) Disconnect the 5P PH-PH CON.CORD from the [CX051] on the STANDBY TRANS UNIT. (3) Disconnect the 2P Wire from the [CX121] on the STAND- BY TRANS UNIT.
Page 18
http://www.xiaoyu163.com S-52/S-52DAB/S-32 6B. 1U-3854 STANDBY TRANS UNIT(for EK) 3 7 63 1515 0 Disconnect the 8P PH-PH SHIELD CORD from the [CY081] on 1U-3847-2. (2) Remove the 2 side screws 117, then detach the DAB SUB ASS’Y. 8P PH-PH SHIELD CORD DAB SUB ASSY (3) Remove the 2 screws 113 and the 1 screw 105 on the rear.
Page 19
http://www.xiaoyu163.com S-52/S-52DAB/S-32 7. POWER TRANS 3 7 63 1515 0 (1) Remove the 4 screws 105 on the rear. 8. 1U-3847-1 POWER AMP UNIT Disconnect the 6P PH-PH SHIELD CORD from the [CY062] on the POWER AMP UNIT. (2) Disconnect the 1P SIN EH CONN CORD from the [CY021] on the POWER AMP UNIT.
Page 20
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 (5) Remove the 2 inside screws 104 and the 2 rear screws 105. 9. 1U-3859-1 POWER UNIT Disconnect the 11P PH-PH CON.CORD from the [CY111] on the POWER UNIT. (2) Disconnect the 6P PH-PH CON.CORD from the [CY061] on the POWER UNIT.
Page 21
http://www.xiaoyu163.com S-52/S-52DAB/S-32 10. 1U-3846 MAIN UNIT 3 7 63 1515 0 Remove the 2 screws 104 where the code holder outside of the side bracket is fixed. (2) Cut off the 1 WIRE CLAMPER and remove.(S-52 only) (3) Disconnect the 16P CON.CORD from the [CX161] on the MAIN UNIT.(S-52E3 only) (4) Disconnect the 15P FFC CABLE from the [CX151] on the MAIN UNIT.(S-52JP/E2/EK,S-32E2/E3)
Page 22
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 (12) Disconnect the 1P SAN EH CON.CORD from CX021 on the Power Amp Unit, then pull out in the direction of the arrow. 1P SAN EH CON. CORD (13A)Remove the 4 screws 105 and the 1 screw 113.(E3 only) (13B)Remove the 3 screws 105 and the 1 screw 113.(JP/E2/ EK only)
Page 23
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 (15) Remove the 6 screws 105 and the 2 screws 104, the 2 washers 118. (16) Disconnect the 15P FFC CABLE from the AM FM TUN- ER.(S-52JP/E2/EK,S-32E2/E3) (17) Disconnect the 9P PH-PH SHIELD CORD from the [CX063] on the POWER UNIT.
Page 24
http://www.xiaoyu163.com S-52/S-52DAB/S-32 11.ROTARY KNOB 3 7 63 1515 0 The SNAP FIT is bent from the back of the CABINET in the direction of the arrow (2) The ROTARY KNOB RING is rotated in the direction of the arrow and detach. (3) Detach the ROTARY KNOB in the direction of the arrow ROTARY KNOB RING SNAP FIT...
Page 25
http://www.xiaoyu163.com S-52/S-52DAB/S-32 DIAGNOSTICS OF OPTICAL PICKUP 3 7 63 1515 0 AND REPLACING TRAVERSE UNIT Make failure diagnostics of the Optical Pickup as follows. If the laser drive current (Iop) becomes more than 1.5 times of the initial value, the Optical Pickup should be replaced. The laser drive current initial value is checked by "Iop checked Method"...
Page 26
http://www.xiaoyu163.com S-52/S-52DAB/S-32 1. Iop checked Method 3 7 63 1515 0 Select the laser ON/OFF (CD) mode of the test mode, and check the lop value of CD laser. (See page 32 for test mode.) 1.1. CD Laser current check (1) Press the button to display the laser current value, and then select T21.
Page 27
http://www.xiaoyu163.com S-52/S-52DAB/S-32 4. Rewriting the default value of the laser 3 7 63 1515 0 current To rewrite the default value of the laser current, press the button for at least 5 seconds while the CD laser current is displayed, then press the button to select T23.
Page 28
http://www.xiaoyu163.com S-52/S-52DAB/S-32 HOW TO REPLACE TRAVERSE UNIT 3 7 63 1515 0 (S-52,S-52ADB) Caution: The optical pickup can be damaged easily by static electricity charged on human body. Take necessary anti-static measures when repairing around the optical pickup. (Follow the procedure below in reverse order when reas- sembling.) 1.
Page 29
http://www.xiaoyu163.com S-52/S-52DAB/S-32 2. Traverse Unit disassembly 3 7 63 1515 0 (1) Solder the short-circuit. (2) Remove 4 screws C. (3) Disconnect FFC from the Pick Up. Solder to short-circuit (4) Lift the Traverse Assy and disconnect FFC. L 13942296513 u163 http://www.xiaoyu163.com...
Page 30
http://www.xiaoyu163.com S-52/S-52DAB/S-32 SERVICE MODE 3 7 6 3 1 5 1 5 0 1. Initial Setting Mode 1.1. Preparation (1) Equipment used: None (2) Unit setting: No spec other than the following procedure. 1.2. Procedure SYSTEM Initialize the backup data when µcom, peripheral parts of µcom, or Main P.W.B. has been replaced in servicing. All user setting will be lost and its factory setting will be restored when this initialization is made.
Page 31
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3. Heat Run Mode (S-52) 3 7 6 3 1 5 1 5 0 3.1. preparation (1) Equipment used: CD (2) Unit setting : No spec other than the following procedure. 3.2. procedure Perform heat run of the CD. (1) Pressing the and DIMMER buttons simultaneously, plug the AC cord into a power outlet.
Page 32
http://www.xiaoyu163.com S-52/S-52DAB/S-32 4. Test mode (S-52) 3 7 6 3 1 5 1 5 0 4.1. Entering the test mode To set the test mode, press the RETURN button before pressing the button in the heat run mode.Not insert the disc. (To set the heat run mode, connect the AC cord and press the FUNCTION ON/OFF button while pressing the and DIMMER buttons simultaneously to turn on the set power.
Page 33
http://www.xiaoyu163.com S-52/S-52DAB/S-32 4.3. Setting the mode 3 7 6 3 1 5 1 5 0 With the mode selected, press the button to set that mode. In the laser on/off (CD) mode, laser on/off control is executed and the laser current is displayed. To save the current laser current value, press and hold in the button for at least 5 seconds to turn off the "mmmm"...
Page 34
http://www.xiaoyu163.com S-52/S-52DAB/S-32 4.4. Change within the mode 3 7 6 3 1 5 1 5 0 Changes within modes are made by pressing the buttons while the mode is set. In the laser on/off mode, laser on/off control is executed and the laser current is displayed. For the CD laser : Off, CD laser, Stored data: mm.mm [mA], Current value: nn.nn [mA]) When there is no saved data...
Page 35
http://www.xiaoyu163.com S-52/S-52DAB/S-32 4.5. Execution of trace mode (error rate display) (See "Table 2 - Trace mode details") 3 7 6 3 1 5 1 5 0 Trace will be performed if the button is pushed after choosing operation. (YY : selection mode [71 to 94], m : address [LBA][HEX], l : error rate [COUNT/SEC] [HEX]) Note) CD : Error rate of 75 frames is displayed (1 second).
Page 36
http://www.xiaoyu163.com S-52/S-52DAB/S-32 5. Product Mode 3 7 6 3 1 5 1 5 0 5.1. Setting the product mode The TUNER and AVAMP set to the puroduct mode. (1) Pressing the and SNOOZE buttons simultaneously, plug the AC cord into a power outlet. This sets the puroduct mode. (2) After power supply turn on, the function is displayed.
Page 37
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 TROUBLE SHOOTING ADV-S52 ADV 5 1. LCD doesn't display (1) Check the Set-up process of System -COM and BF(DSP) Check Power Supply Voltages for System uCOM. 1U-3846-1(MAIN UNIT) Check Soldering. +3.3V_DNS 1U-3859-4(STANDBY TRANS UNIT).
Page 38
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 Check Reset signal for LCD 1U-3846-1(MAIN UNIT) Check Soldering. [LCD_RST] CX262 on MAIN UNIT. "H"level O.K.? O.K. Check control signal for LCD. Check Soldering. 1U-3846-1(MAIN UNIT) IC102,IC103,IC106,IC107 on MAIN UNIT. [LCD_RS],[LCD_WR],[LCD_CS],[D0-7] IC701,TR703-705,CY064 on MAIN UNIT.
Page 39
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 3. No Sound,Noise generated (1) CD PLAY(S-52,S-52DAB only) Check Power Supply Voltages for AUDIO. 1U-3846-1(MAIN UNIT) Check Soldering. +12V_A1 1U-3859-1(POWER UNIT). CX111 on MAIN UNIT. O.K. Check Power Supply Voltages for CODEC(IC300). 1U-3846-1(MAIN UNIT) Check Soldering.
Page 40
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 Check Analog Audio Data output from CODEC to AMP. 1U-3846-1(MAIN UNIT) Check Soldering. [IC300] output and [IC301] input [IC300]:40,41pin on MAIN UNIT. [Lch],[Rch] [IC301] on MAIN UNIT. O.K. Check audio mute signal. Check Soldering.
Page 41
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 (2) AM/FM TUNER-in(S-52E2JP,S-52DAB,S-32 only) Check Power Supply Voltages for AM/FM TUNER. 1U-3846-1(MAIN UNIT) Check Soldering. +12V_A TR304,TR306,TR307,TR308 +5V_A CX151 on MAIN UNIT. O.K. Check Analog Audio Data output from TUNER PACK to CODEC.
Page 42
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 (4) IPOD-IN Check Power Supply Voltages for IPOD. 1U-3846-1(MAIN UNIT) Check Soldering. F/W PWR+:+12V OK? TR311,TR314,CX131 on MAIN UNIT. +5V_D1 O.K. Check control signal for IPOD. Check Soldering. 1U-3846-1(MAIN UNIT)/1U-3859-2(IPOD I/O UNIT) [IC701]:53,55,56pin on MAIN UNIT.
Page 43
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 (6) XM RADIO-in(S-52E3 only) Check Power Supply Voltages for XM Ready circuit. 1U-3846-1(MAIN UNIT) Check Soldering. +5.3V_XM IC108,CY111 on POWER UNIT. +3.3V_XM IC711,CX111,CX081 on MAIN UNIT. O.K. Check Reset signal for XM Ready circuit. 1U-3846-1(MAIN UNIT) Check Soldering.
Page 44
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 Check Digital Audio Data Clock from Clock selector Check Soldering. to BF/CODEC. 1U-3846-1(MAIN UNIT) [IC305]:8,6,3pin on MAIN UNIT. [IC305]output and [IC101]/[IC300]input: [IC300]:24,11,10pin on MAIN UNIT. [CODEC_256FS],[CODEC_64_FS],[CODEC_FS] R314,R304,R303 on MAIN UNIT. O.K.
Page 45
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 (8) ETHERNET-in Check Power Supply Voltages for DM850(IC501) and PHY(IC504). 1U-3846-1(MAIN UNIT) Check Soldering. +3.3V_E1 IC511,IC512 on MAIN UNIT. +1.8V_E1 [IC701]:67pin on MAIN UNIT. [E_POWER]:"H"level OK? O.K. Check Reset signal for DM850. 1U-3846-1(MAIN UNIT) Check Soldering.
Page 46
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 Check Digital Audio Data output from DM850 to CODEC. 1U-3846-1(MAIN UNIT) Check Soldering. [DM850] output and [IC300] input [IC501]:39pin,R198 on MAIN UNIT. [SPDIF_ETHER] [IC300]:4pin on MAIN UNIT. O.K. Check Digital Audio Data output from CODEC to BF. 1U-3846-1(MAIN UNIT) Check Soldering.
Page 47
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 (10) WiFi-in Check Power Supply Voltages for WiFi. and PHY(IC504). 1U-3846-1(MAIN UNIT) Check Soldering. +3.3V_E1 IC511 on MAIN UNIT. O.K. Check Reset signal for WiFi. 1U-3846-1(MAIN UNIT) Check Soldering. [WL_RST]:"H"level O.K.? [IC501]:10pin,RR103,RR320 on MAIN UNIT.
Page 48
http://www.xiaoyu163.com S-52/S-52DAB/S-32 BLOCK DIAGRAMS S-52,S52DAB 3 7 6 3 1 5 1 5 0 S52 SYSTEM PART BLOCK DIAGRAM KEY/RC K8D3216UBC W9812G6GH K8D1716UBC 128M SDRAM W9812G6GH 32M Frash 16M Frash 128M SDRAM Broad Com WiFi Address/Data BUS Ad/Data BUS BD4727 Reset ADSP-BF532 DM-850E...
Page 49
http://www.xiaoyu163.com S-52/S-52DAB/S-32 S-32 3 7 6 3 1 5 1 5 0 S32 SYSTEM PART BLOCK DIAGRAM KEY/RC K8D3216UBC W9812G6GH K8D1716UBC W9812G6GH 32M Frash 128M SDRAM 16M Frash 128M SDRAM Broad Com WiFi Address/Data BUS Ad/Data BUS BD4727 Reset ADSP-BF532 DM-850E M30879FKBGP X'TAL...
Page 51
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. 1. IC’s DM850E (IC502) L 13942296513 u163 http://www.xiaoyu163.com...
Page 52
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 DM850E Pin Assignment by Pin Number Name Name Name Name VSSIO USBREF A[19] VSSIO AV0CLK VSSIOUSB A[2 0] VDDIO VDDIO VDDIOUSB A[2 1] A[5 ] AV0DATA[0] VDDUSBPLL NW E A[6 ] AV0DATA[1] VSSUSBPLL NCS[2] AV1DATA[0] AV0DATA[2]...
Page 53
http://www.xiaoyu163.com S-52/S-52DAB/S-32 ADSP-BF532 (IC101) 3 7 63 1515 0 9 10 11 12 13 14 KEY : DDINT DDRTC DDEXT ROUT (Top View) ADSP-BF532 Ball Number Ball No. Signal Ball No. Signal Ball No. Signal Ball No. Signal VDDEXT DT0PRI SCAS DT0SEC TFS0...
Page 60
http://www.xiaoyu163.com S-52/S-52DAB/S-32 PRINTED WIRING BOARDS 3 7 6 3 1 5 1 5 0 1U-3846 MAIN P.W.B. UNIT (1/2) 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 COMPONENT SIDE http://www.xiaoyu163.com...
Page 61
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 1U-3846 MAIN P.W.B. UNIT (2/2) 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 FOIL SIDE http://www.xiaoyu163.com...
Page 62
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 1U-3847 VIDEO P.W.B. UNIT (1/2) 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 COMPONENT SIDE COMPONENT SIDE http://www.xiaoyu163.com...
Page 63
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 1U-3847 VIDEO P.W.B. UNIT (2/2) 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 FOIL SIDE FOIL SIDE http://www.xiaoyu163.com...
Page 64
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 1U-3851 L.PWR/DISP P.W.B. UNIT (1/2) 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 COMPONENT SIDE http://www.xiaoyu163.com...
Page 65
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 1U-3851 L.PWR/DISP P.W.B. UNIT (2/2) 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 FOIL SIDE http://www.xiaoyu163.com...
Page 66
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 1U-3859 D.AMP/SMPS P.W.B. UNIT (1/2) 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 COMPONENT SIDE http://www.xiaoyu163.com...
Page 67
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 6 3 1 5 1 5 0 1U-3859 D.AMP/SMPS P.W.B. UNIT (2/2) 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 FOIL SIDE FOIL SIDE http://www.xiaoyu163.com...
Page 68
http://www.xiaoyu163.com S-52/S-52DAB/S-32 NOTE FOR PARTS LIST 3 7 63 1515 0 • Parts for which "nsp" is indicated on this table cannot be supplied. • When ordering of part, clearly indicate "1" and "I" (i) to avoid mis- supplying. • Ordering part without stating its part number can not be supplied.
Page 69
http://www.xiaoyu163.com S-52/S-52DAB/S-32 PARTS LIST OF P.W.B. UNIT 3 7 63 1515 0 Parts for which "nsp" is indicated on this table cannot be supplied. The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks"...
Page 70
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 Ref. No. Part No. Part Name Remarks Q'ty New IC707 00D 262 3742 905 F2621E-01 for S-52E3 IC708 00D 273 0492 902 SP8K3FU6TB for S-52E3 IC711 00D 262 2977 946 BA33BC0FP-E2 +REF for S-52E3/DABEK IC871 00D 263 0673 902 BA10393F-E2...
Page 78
http://www.xiaoyu163.com S-52/S-52DAB/S-32 1U-3859 POWER /IPOD UNIT P.W.B. UNIT ASS'Y 3 7 63 1515 0 Ref. No. Part No. Part Name Remarks Q'ty New SEMICONDUCTORS GROUP IC100 00D 263 1100 021 KIA7812API-U/P IC101-103 00D 263 1219 006 BD9702T-V5 IC108 00D 263 1223 005 PQ20RX11J00H for S-52E3/DABEK IC306...
Page 79
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 Ref. No. Part No. Part Name Remarks Q'ty New C147-149 00D 254 4708 905 CE04W1E221MT HB5(KY) C150 CK73F1H103ZT +1608 C200 00D 254 4533 934 CE04W0J221MT SMG/RE3 for S-52 C201-203 CK73F1E104ZT +1608 for S-52 C206 CK73F1E104ZT +1608...
Page 80
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 Ref. No. Part No. Part Name Remarks Q'ty New F103 00D 206 1015 029 FUSE 1A T for S-52DABEK F103 00D 206 1035 054 FUSE 1.6A (T) for S-52JP FB100 00D 235 0147 909 E.FIL(BLM21PG221SN1)+2125 for S-52 FF100-103...
Page 81
http://www.xiaoyu163.com S-52/S-52DAB/S-32 EXPLODED VIEW 3 7 6 3 1 5 1 5 0 S-52/S-52DAB model only S-52/S-52DAB model only S-52/S-52DAB model only 4-10 4-11 4-12 S-52/S-52DAB model only For details on , refer to exploded view of CD mechanism unit. 1 3 9 4 2 2 9 6 5 1 3 WARNING: Parts marked with this symbol...
Page 82
http://www.xiaoyu163.com S-52/S-52DAB/S-32 PARTS LIST OF EXPLODED VIEW 3 7 63 1515 0 Parts for which "nsp" is indicated on this table cannot be supplied. ASS’Y ASS’Y P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts. The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
Page 83
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 Ref. No. Part No. Part Name Remarks Q'ty New WINDOW for S-52JP WINDOW for S-32E2 WINDOW for S-32E3 METAL NET (L) MATAL NET (R) BLIND SHEET SUPPORT SHEET DOCK LID ASSY 4-10 DOC LID COVER 4-11 DOCK ESC 4-12...
Page 84
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 Ref. No. Part No. Part Name Remarks Q'ty New TOP BRACKET PWB BRACKET PROTECTION SHEET PUSH RIVET CORD HOLDER FGDVS202MS CD MECHA UNIT for S-52 MAIN CHASSIS for S-32 E2 LASER CAUTION for S-52E2/DABEK LABEL(A) for S-52E3 BOTTOM COVER...
Page 85
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 Ref. No. Part No. Part Name Remarks Q'ty New NOISE INSULATE (BTM) for S-52 SCREWS 2.6X5 CBTS (S)-Z 2.6X8 CBTS (P)-Z 3X4 CBTS (S)-Z 3X6 CBTS(S)-Z 3X6 CBTS(S)-B 3X6 CBTS (S)-B 3X8 CBTS (P)-B 3X8 CBTS(B)-B 3X10 CBTS (P)-Z 3X10 CBTS(B)-Z...
Page 86
http://www.xiaoyu163.com S-52/S-52DAB/S-32 EXPLODED VIEW OF CD MECHANISM UNIT 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
Page 87
http://www.xiaoyu163.com S-52/S-52DAB/S-32 PARTS LIST OF CD MECHANISM UNIT(S-52) 3 7 63 1515 0 Parts for which "nsp" is indicated on this table cannot be supplied. The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Ref.
Page 89
http://www.xiaoyu163.com S-52/S-52DAB/S-32 PARTS LIST OF PACKING & ACCESSORIES 3 7 63 1515 0 Parts for which "nsp" is indicated on this table cannot be supplied. The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks"...
Page 90
http://www.xiaoyu163.com S-52/S-52DAB/S-32 WIRING DIAGRAMS S-32 3 7 6 3 1 5 1 5 0 Jumper 1U-3847-7 JOG ENCODER UNIT S32 WIRING DIAGRAM H/P OUT JACK Portable IN JACK iPod DOCK Connector 1U-3847-3 REMOTO SENSOR Jumper 1U-3847-4 1U-3847-6 1U-3847-5 /LCD UNIT 1U-3859-2 H/P PORTBLE IN UNIT ALARM UNIT...
Page 91
http://www.xiaoyu163.com S-52/S-52DAB/S-32 S-52 3 7 6 3 1 5 1 5 0 Jumper 1U-3847-7 S52 WIRING DIAGRAM JOG ENCODER UNIT USB Connector JACK (S52 ONLY) H/P OUT JACK Portable IN JACK iPod DOCK Connector 1U-3847-3 REMOTO SENSOR 1U-3859-3 Jumper 1U-3847-4 1U-3847-6 1U-3847-5 /LCD UNIT...
Page 92
http://www.xiaoyu163.com S-52/S-52DAB/S-32 MEASURING METHOD AND WAVEFORMS 3 7 63 1515 0 To check the waveforms on the FEP, the GND (-) probe of the oscilloscope to “VHALF” point. (Except for lnner SW, TRVSW) NOTES Measuring Disc: CD/TCD-784 (It is better to use wires for extending between the probe and test points.) •...
Page 93
http://www.xiaoyu163.com S-52/S-52DAB/S-32 WAVEFORMS 3 7 63 1515 0 IU-3851 FEP Unit CD PLAY Disc : TCD-784 RF waveform SEARCH (INNER OUTER) NARF TRSDRV RANGE 20 msec RANGE .2 v CD PLAY (INNER) CD LOADING PLAY FODRV L 13942296513 SPDRV RANGE .1 v 1 msec .5 v...
Page 94
http://www.xiaoyu163.com S-52/S-52DAB/S-32 3 7 63 1515 0 IU-3846 MAIN Unit Wave form 3 : CLOCK Waveform (12.288MHz) Wave form1: PWR_OFF_DET 50/60 Waveform CX051 5pin X301 (Refer to the SCHEMATIC DIAGRAMS 4/7) (Refer to the SCHEMATIC DIAGRAMS 3/7) L 13942296513 Wave form 4 : A/D Waveform Wave form 2 : CLOCK Waveform (11.2896MHz) CH1:IC300 10pin X302...
Page 95
http://www.xiaoyu163.com S-52/S-52DAB/S-32 NOTE FOR SCHEMATIC DIAGRAM 3 7 63 1515 0 WARNING: Parts marked with this symbol ! have critical characteristics. Use ONLY replacement parts recommended by the manufactur- CAUTION: Before returning the unit to the customer, make sure you make µ...
Page 96
SCHEMATIC DIAGRAMS (1/7) S-52 / S-52DAB / S-32 http://www.xiaoyu163.com 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 SIGNAL LINE SCHEMATIC DIAGRAMS (1/7) 1U-3846-1 MAIN UNIT(1/4) Note :...
Page 97
SCHEMATIC DIAGRAMS (2/7) S-52 / S-52DAB / S-32 http://www.xiaoyu163.com 3 7 6 3 1 5 1 5 0 Wifi ETHERNET 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 SIGNAL LINE SCHEMATIC DIAGRAMS (2/7) 1U-3846-1 MAIN UNIT(2/4)
Page 98
SCHEMATIC DIAGRAMS (3/7) S-52 / S-52DAB / S-32 http://www.xiaoyu163.com 3 7 6 3 1 5 1 5 0 HD Analog iPod TUNER Portable In ETHERNET/Wifi/USB 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 SIGNAL LINE SCHEMATIC DIAGRAMS (3/7) Note :...
Page 99
SCHEMATIC DIAGRAMS (4/7) S-52 / S-52DAB / S-32 http://www.xiaoyu163.com 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 SIGNAL LINE SCHEMATIC DIAGRAMS (4/7) 1U-3846-1 MAIN UNIT(4/4) Note :...
Page 100
SCHEMATIC DIAGRAMS (5/7) S-52 / S-52DAB / S-32 http://www.xiaoyu163.com 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 w w w SCHEMATIC DIAGRAMS (5/7) SIGNAL LINE u 1 6 3 1U-3847 POWER AMP/KEY UNIT(1/1) 1U-3847-1 SENSOR UNIT 1U-3847-2 DAB INTERFACE UNIT (EK model only)
Page 101
SCHEMATIC DIAGRAMS (6/7) S-52 / S-52DAB / S-32 http://www.xiaoyu163.com 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 Note : [Sheet 1] : SCHEMATIC DIAGRAMS (1/7), 1U-3846 MAIN UNIT - BF block [Sheet 2] : SCHEMATIC DIAGRAMS (2/7), 1U-3846 MAIN UNIT - ETHER/USB/WiFi block [Sheet 3] : SCHEMATIC DIAGRAMS (3/7), 1U-3846 MAIN UNIT - ANALOG AUDIO IF/CODEC block [Sheet 4] : SCHEMATIC DIAGRAMS (4/7), 1U-3846 MAIN UNIT - SYSTEM uCOM block...
Need help?
Do you have a question about the S-52 DAB and is the answer not in the manual?
Questions and answers