Mitsubishi Electric PUMY-P100VHMB Service Manual page 9

Model
Power source
Cooling capacity
(Nominal)
Power input
Current input
COP (kW/kW)
Indoor
Temp. range of
Outdoor
cooling
Heating capacity
(Nominal)
Power input
Current input
COP (kW/kW)
Indoor temp.
Temp. range of
Outdoor temp.
heating
Total capacity
Indoor unit
Model/Quantity
connectable
Noise level
(measured in anechoic room)
Liquid (High press.)
Diameter of
refrigerant pipe
Gas (Low press.)
External finish
External dimension H × W × D
Net weight
Heat exchanger
Compressor Type
Manufacturer
Starting method
Motor output
Case heater
Lubricant
FAN Air flow rate
External static press.
Type × Quantity
Control, Driving mechanism
Motor output
HIC circuit (HIC: Heat Inter-Changer)
Protection
High pressure protection
Inverter circuit (COMP./FAN)
Compressor
Fan motor
Defrosting method
Refrigerant Type × Original charge
Control
Standard Document
attachment Accessory
Optional parts
Remark
* 1 Nominal cooling conditions
Note :
Indoor :
27˚CDB/19˚CWB (81˚FDB/66˚FWB)
Outdoor :
35˚CDB (95˚FDB)
Pipe length :
7.5 m (24-9/16 ft)
Level difference : 0 m (0 ft)
* Nominal conditions * 1, * 3 are subject to JIS B8615-1.
* Due to continuing improvement, above specifications may be subject to change without notice.
PUMY-P100YHMB(-BS)
PUMY-P100YHMBR1(-BS)
PUMY-P100YHMBR2(-BS)
kW
11.2
* 1
kcal/h
* 1 9,600
Btu/h
* 1 38,200
kcal/h
* 2 -
kW
3.30
A
5.28-5.02-4.84
3.39
W.B.
D.B.
10 to 46˚CD.B. (50 to 115˚FD.B.): in case of connecting PKFY-P15/P20/P25 type indoor unit.
* 3 kW 12.5
kcal/h
* 3 10,800
* 3 Btu/h
42,700
kW
3.63
A
5.81-5.52-5.32
3.44
D.B.
W.B.
P15 ~ P125/1 ~ 8
dB <A>
49/51
mm (in.)
ø9.52 (ø3/8") Flare
mm (in.)
ø15.88 (ø5/8") Flare
mm
1,350 × 950 × 330
in.
53-3/16" × 37-7/16" × 13"
kg (lb) 142 (313)
Salt-resistant cross fin & copper tube
Inverter scroll hermetic comp.
kW
1.9
kW
-
FV50S × 2.3 L
m /min 100
3
L/s 1667
cfm
3532
0 Pa
Propeller fan × 2
DC-control, Direct-driven by motor
kW 0.06 × 2
Discharge thermo protection, Over-current protection (PUMY-P·VHMB(-BS), PUMY-P·VHMBR1(-BS))
Compressor thermo protection, Over-current protection (PUMY-P·VHMBR2(-BS))
R410A × 8.5kg (19 lb)
Joint: CMY-Y62-G-E
Header:CMY-Y64/68-G-E
Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items
shall be referred to the Installation Manual.
* 2 Nominal cooling conditions
27˚CDB/19.5˚CWB (81˚FDB/67˚FWB)
35˚CDB (95˚FDB)
5 m (16-3/8 ft)
0 m (0 ft)
PUMY-P125YHMB(-BS)
PUMY-P125YHMBR1(-BS)
PUMY-P125YHMBR2(-BS)
3-phase 4-wire 380-400-415V 50Hz
14.0
12,000
47,800
12,500
4.27
6.83-6.49-6.26
3.28
15 ~ 24˚C (59 ~ 75˚F)
- 5 ~ 46˚C (23 ~ 115˚F)
16.0
13,800
54,600
4.29
6.87-6.52-6.29
3.73
15 ~ 27˚C (59 ~ 81˚F)
-15 ~ 15˚C (5 ~ 59˚F)
50 ~ 130% of outdoor unit capacity
P15 ~ P140/1 ~ 10
50/52
ø9.52 (ø3/8") Flare
ø15.88 (ø5/8") Flare
Galvanized steel sheet
<MUNSELL 3Y 7.8/1.1>
1,350 × 950 × 330
53-3/16" × 37-7/16" × 13"
142 (313)
Salt-resistant cross fin & copper tube
Inverter scroll hermetic comp.
MITSUBISHI ELECTRIC CORPORATION
Inverter
2.4
-
FV50S × 2.3 L
100
1667
3532
0 Pa
Propeller fan × 2
DC-control, Direct-driven by motor
0.06 × 2
-
High pressure sensor, High pressure switch 4.15 MPa
Over-heat protection, Over-current protection
Over-heat protection, Voltage protection
Auto-defrost mode (Reversed refrigerant circle)
R410A × 8.5kg (19 lb)
LEV circuit
Installation Manual
Grounded lead wire x 2
Joint: CMY-Y62-G-E
Header:CMY-Y64/68-G-E
* 3 Nominal heating conditions
20˚CDB (68˚FDB)
7˚CDB/6˚CWB (45˚FDB/43˚FWB)
7.5 m (24-9/16 ft)
0 m (0 ft)
9
PUMY-P140YHMB(-BS)
PUMY-P140YHMBR1(-BS)
PUMY-P140YHMBR2(-BS)
15.5
13,300
52,900
14,000
5.32
8.51-8.09-7.80
2.91
18.0
15,500
61,400
5.32
8.51-8.09-7.80
3.38
P15 ~ P140/1 ~ 12
51/53
ø 9.52 (ø3/8") Flare
ø 15.88 (ø5/8") Flare
1,350 × 950 × 330
53-3/16" × 37-7/16" × 13"
142 (313)
Salt-resistant cross fin & copper tube
Inverter scroll hermetic comp.
2.9
-
FV50S × 2.3 L
100
1667
3532
0 Pa
Propeller fan × 2
DC-control, Direct-driven by motor
0.06 × 2
R410A × 8.5kg (19 lb)
Joint: CMY-Y62-G-E
Header:CMY-Y64/68-G-E
Unit converter
×
kcal/h = kW 860
×
Btu/h = kW 3,412
×
3
cfm = m /min 35.31
lb = kg/0.4536
*Above specification data is
subject to rounding variation.