Maintenance - Superior DRT63STTEN Installation And Operation Instructions Manual

INNOVATIVE HEARTH PRODUCTS • SEE-THROUGH DIRECT-VENT GAS FIREPLACES (DRT63STTEN/P) • INSTALLATION INSTRUCTIONS

MAINTENANCE

(See Maintenance Schedule, Page 56)
Refer to the maintenance schedule for
maintenance tasks, procedures, frequency and
by whom they should be performed. Always
verify proper operation of the appliance after
servicing.
WARNING
Turn off gas and electrical power
to the fireplace and allow it to
cool before cleaning or servicing
the appliance.
CAUTION: Wear gloves and safety glasses
for protection while doing required
maintenance.
Verify proper operation after servicing.
S'assurer que l'appareil fonctionne adé-
quatement une fois l'entretien terminé.
Always turn off gas to the pilot before
cleaning. Before relighting, refer to
the lighting instructions in this manual.
Instructions are also found on a pull-out
panel located in the control compartment.
Before relighting the fireplace, refer
to the lighting instructions in this
manual. Instructions are also found on
pull-out panels located in the control
compartment.
Inspect Venting System
The appliance and venting system should be
thoroughly inspected before initial use and
at least annually by a qualified service techni-
cian (inspection should include ensuring that
exhaust or intake passages are unobstructed
and vent components are properly assembled
and not damaged). Homeowner must contact
a qualified service technician at once if any
abnormal condition is observed.
If the venting system is disassembled for any
reason, a qualified service technician should
follow vent installation instructions for proper
reassembly and proper sealing of the venting
system components. However, more frequent
periodic inspections and cleanings should be
performed by the homeowner.
Glass Cleaning
(For detailed glass door assembly removal/
installation instructions, see Page 44.)
Note: Clean glass after first two weeks of
44
operation (after burn-in period is over) and
then only when necessary and ONLY WHEN
THE APPLIANCE IS COOL. Wipe surface with
clean, dampened, soft cloth. Follow with dry,
soft towel as desired. Take care not to scratch
the glass surface.
IMPORTANT: Do not use abrasive
cleaners on glass. Never clean the glass
when it is hot.
Clean the glass periodically, to remove any
buildup caused by the following:
• Filmy coating (during initial use after instal-
lation). Initial curing of the high temperature
paint and burning off of lubricants used in
the manufacturing process may result in a
filmy coating on the glass.
• Dusty or dirty buildup. It is normal for con-
densation and fog to form on the inside of
the glass when first starting the appliance.
This condensation and fog will usually
disappear within a few minutes; however,
over time the moisture can cause lint, dust,
and other airborne particles to cling to the
glass surface.
• White coating. A white coating may form
on the glass as a result of impurities and
minerals in the fuel.
It is recommended that the glass be cleaned
two or three times during each heating season,
depending on the circumstances. The follow-
ing cleaning solutions are approved for use to
clean the glass:
• Non-ammonia based household cleaner
• 50% white vinegar and 50% water
• Gas fireplace/stove glass cleaner
Barrier (see Notice, Page 26)
NOTE: Make sure fireplace is OFF and unit is
COLD before removing barrier
To remove barrier follow these steps.
1.Lift barrier up by the frame at the top.
2.Remove lower filler piece by pulling down
off of the barrier.
3.Lower barrier and push barrier to left to
release right side.
4.Pull the right side out of fireplace.
5.Remove screen.
6. Install the new, approved factory barrier with
flat side of screen toward firebox.
Inspect Glass Gasket
Visually inspect the gasket on the backside of the
glass enclosure panels. The gasket surface must
be clean, free of irregularities and seated firmly.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Clean Control Compartment
Keep control compartment clean by vacuuming
or brushing at least twice a year. More frequent
cleaning may be required due to excessive lint
from carpeting, bedding materials, etc. It is
important that control compartments, burners
and circulating air passageways of the appliance
be kept clean.
Clean Logs and Burner
Carefully remove the logs (use care when han-
dling the fiber logs, as they become quite fragile
after curing). Vacuum out any foreign matter
(lint, carbon, etc.) on the burner. Ensure the
burner ports are "open." Remove any carbon
deposits from the under side of the logs using
a vacuum cleaner, or a soft bristled brush (i.e.
paint brush).
Note: Improper positioning of logs can create
carbon build-up and will alter the performance
of the appliance.
Replacing Logs
If the logs become damaged by accident or
improper handling and need replacement,
use only the proper replacement logs from
manufacturer (see Pages 51, 58, and 59 for
ordering information).
Reinstall Embers, Volcanic Stone,
and Logs
Carefully follow placement instructions on
Pages 46–48). All logs should fit onto cor-
responding pins and/or log stoppers. This will
ensure a proper flame and safe combustion.
Inspect Wiring
Refer to wiring diagram on Page 51.
CAUTION: Label all wires prior to disconnec-
tion when servicing controls. Wiring errors
can cause improper and dangerous operation.
Verify proper operation after servicing.
ATTENTION: Au moment de l'entretien des
commandes, étiquetez tous les fils avant
de les débrancher. Des erreurs de cáblage
peuvent entraîner un fonctionnement
inadéquat et dangereux.
Inspect and clean all wire connections. Ensure
that there is no melting or damage. Inspection
should include:
• Terminals at the valve
• OFF/ON Switch
Inspect Burner Flame Appearance
Ensure that the burner flame appearance
resembles the flame shown in Figures 76 and
77 and as described in Flame Appearance and
Sooting on Page 49. The homeowner must
contact a qualified service technician at once
if any abnormal condition is observed.