Torque Values - Shindaiwa 300 Service Manual

Values glven in Illch/pounds and (Kg cm)
Section
14
Appendix Torque Values
1 inch/pound '" 1.152 Kg-cm
1 Kg-cm
=
0.868
In
lbs,)
300, 300S , 360, 575 ,680,
Location* 377, 488 695 577 757 357
E ng lne C ran kcase 61 -70 (70-80) 70-80 (80-90) 70-80 (80-90) 61-7D (70-80) 52-69 (60-80)
Cyli nder lo C rankcase 61 -70 (70-80) 70-80 (80-90) 70-80 (80-90) 79-104 (90-120) N/A
Boo t/lnsulalor lo Cylinder 17-22 (20-25) 17-22 (20-25) 79-104 (90- 120)
Flywh ee l Nul 104-122 (120­ 140) 122-140 (140-160) 200-208 (230-240) 200-208 (230-240) 104-122 (122-140)
Mu ftle r Bo lt 61-70 (70-80) 70-79 (80-90) 70-79 (80-90) 5 mm 70- 79 (80-90) 61-70 (70-80)
6 mm 105 (120)
Spark Plug 148-165 (1 70- 190) 148-165 (1 70-190) 148-165 (170-190) 148-165 (170-190) 148-165 (170-190)
O il Pump
17 -22 (20-25) 17-22 (20-25) 17-22 (2 -25)
17-22 (20-25)
17-22 (20-25
TC I/Spark Coi l 35 -44 (40-50) 26 -30 (30-35) 26-30 (30-35) 26-30 (30-35)
N/A
E xc iter Coil 35-44 (40-50) 26-44 (30-50) 26-44 (30-50) 26-44 (30-50) N/A
Carburelor (4 mm) 17 -25 (20-30) 17 -25 (20-30) 17-25 (20-30) 17-25 (20-30) 17-25 (20-30)
C arburetor (5 mm) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40)
Front Handle (5 mm) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40)
Front Hand le (55 mm) 25 -44 (30-50) 25-44 (30-50) 25 -44 (30-50) 25-44 (30-50) 25-44 (30-50)
Pulser Coil
N /A
26-44 (30-40)
N /A
N/A
N/, C l ,
"Use Three Bond'M 140110secure P hillips head screws and all olher
lasteners 4mm in diameter and smaller. E xcepl lor screws pre-coaled Irom
Ihe laclory, apply Three Bond
' M
1360 lo all muffler and crankcase screws.
** In stall wilh ThreeBond
T.
1401an lighlen per "Other Fas tener " (below)
DO NO T OVE R TIGHTENI
AII Other Fasteners Socket Head Ph illips Head Nut
4 mm 25-39 (30-45) 13-22 (15-25)
5mm 43-61 (50-70) 25-35 (30-40) 23-30 (2 6-35)
6mm 79-104 (90-120) 35-52 (40-60)
8mm 90-106 (104-122)
~> Shlrdalwa In e. 995
130