Torque Values - Shindaiwa 300 Service Manual

14 Appendix Torque Values
Section
Location*
Engine Crankcase
Cylinder to Crankcase
Boot/Insulator to Cylinder
Flywheel Nut
Muffler Bolt
Spark Plug
Oil Pump
TCI/Spark Coil
Exciter Coil
Carburetor (4 mm)
Carburetor (5 mm)
Front Handle (5 mm)
Front Handle (5.5 mm)
Pulser Coil
*Use Three Bond 1401 to secure Phillips head screws and all other
fasteners 4mm in diameter and smaller. Except for screws pre-coated from
the factory, apply Three Bond
**Install with Three Bond 1401 and tighten per "Other Fasteners" (below).
DO NOT OVERTIGHTEN!
All Other Fasteners
4 mm
5 mm
6 mm
8 mm
130
Shindaiwa Inc. 1995
300, 300S, 360, 575, 680,
377, 488
61-70 (70-80) 70-80 (80-90)
61-70 (70-80) 70-80 (80-90)
** 17-22 (20-25)
104-122 (120-140) 122-140 (140-160) 200-208 (230-240) 200-208 (230-240) 104-122 (122-140)
61-70 (70-80) 70-79 (80-90)
148-165 (170-190) 148-165 (170-190) 148-165 (170-190) 148-165 (170-190) 148-165 (170-190)
17-22 (20-25) 17-22 (20-25)
35-44 (40-50) 26-30 (30-35)
35-44 (40-50) 26-44 (30-50)
17-25 (20-30) 17-25 (20-30)
25-35 (30-40) 25-35 (30-40)
25-35 (30-40) 25-35 (30-40)
25-44 (30-50) 25-44 (30-50)
N/A 26-44 (30-40)
1360 to all muffler and crankcase screws.
Socket Head Phillips Head
25-39 (30-45) 13-22 (15-25)
43-61 (50-70) 25-35 (30-40)
79-104 (90-120) 35-52 (40-60)
—
695 577
70-80 (80-90)
70-80 (80-90)
17-22 (20-25)
70-79 (80-90)
17-22 (20-25)
26-30 (30-35)
26-44 (30-50)
17-25 (20-30)
25-35 (30-40)
25-35 (30-40)
25-44 (30-50)
N/A
Nut
—
23-30 (26-35)
—
— 90-106 (104-122)
Values given in inch/pounds and (Kg-cm)
1 inch/pound = 1.152 Kg-cm
1 Kg-cm = 0.868 in. lbs.)
757 357
61-70 (70-80) 52-69 (60-80)
79-104 (90-120) N/A
79-104 (90-120) **
5 mm: 70-79 (80-90) 61-70 (70-80)
6 mm: 105 (120)
17-22 (20-25) 17-22 (20-25)
26-30 (30-35) N/A
26-44 (30-50) N/A
17-25 (20-30) 17-25 (20-30)
25-35 (30-40) 25-35 (30-40)
25-35 (30-40) 25-35 (30-40)
25-44 (30-50) 25-44 (30-50)
N/A N/A