Sony D-EJ2000 Service Manual

Portable
Hide thumbs Also See for D-EJ2000:

Advertisement

SERVICE MANUAL
Ver 1.1 2002. 12
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance
of 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
D-A conversion
1-bit quartz time-axis control
Frequency response
+1
20 - 20 000 Hz
dB (measured by JEITA CP-
–2
307)
Output (at 3 V input level)
Line output (stereo minijack)
Output level 0.7 V rms at 47 kΩ
Recommended load impedance over 10 kΩ
Headphones (stereo minijack)
Approx. 5 mW + Approx. 5 mW at 16 Ω
(Approx. 0.5 mW + Approx. 0.5 mW
at 16 Ω)*
*For the customers in Europe
Optical digital output (optical output connector)
Output level: –21 - –15 dBm
Wavelength: 630 - 690 nm at peak level
Sony Corporation
9-874-158-02
2002L1600-1
Personal Audio Company
© 2002.12
Published by Sony Engineering Corporation
Photo : SILVER TYPE
Model Name Using Similar Mechanism NEW
CD Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
Power requirements
For the area code of the model you
purchased, check the upper left side of the
bar code on the package.
• Sony NH-14WM (A) rechargeable battery:
1.2 V DC
• LR6 (size AA) battery: 1.5 V DC
• AC power adaptor (DC IN 3 V jack):
US, Canadian models: 120 V, 60 Hz
UK model: 230 V, 50 Hz
Australian model: 240 V, 50 Hz
AEP, JE, E18, KR and EE models:
100 - 240 V, 50/60 Hz
HK model: 230 V, 50 Hz
Chinese model: 220 V, 50 Hz
Battery life* (approx. hours)
(When you use the CD player on a flat and stable
surface.)
Playing time varies depending on how the CD
player is used.
D-EJ2000
Canadian Model
• Abbreviation
E18 : 100 – 230 V AC area in E model
CDM-3325ES2
HK : Hong Kong model
JE
DAX-25E
KR : Korean model
EE
When using
NH-14WM (A)
(charged for
about 5 hours**)
External battery case
(alkaline battery***)
NH-14WM (A) and
external battery case
(alkaline battery***)
* Measured value by the standard of JEITA (Japan
Electronics and Information Technology
Industries Association).
** Charging time varies depending on how the
rechargeable battery is used.
*** When using a Sony alkaline battery LR6 (SG)
(produced in Japan)
Operating temperature
5°C - 35°C (41°F - 95°F)
Dimensions (w/h/d) (excluding
projecting parts and controls)
Approx. 127.0 × 133.8 × 13.4 mm
(5 × 5
×
3
17
8
32
Mass (excluding accessories)
Approx. 118 g (4.2 oz)
Design and specifications are subject to change
without notice.
PORTABLE CD PLAYER
US Model
AEP Model
UK Model
E Model
Chinese Model
Tourist Model
: Tourist model
: East European model
G-PROTECTION
"1"
"2"
25
22
39
34
63
55
in.)

Advertisement

Table of Contents
loading

Summary of Contents for Sony D-EJ2000

  • Page 1 ** Charging time varies depending on how the 307) Battery life* (approx. hours) rechargeable battery is used. *** When using a Sony alkaline battery LR6 (SG) (When you use the CD player on a flat and stable Output (at 3 V input level) (produced in Japan) surface.)
  • Page 2: Table Of Contents

    DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE also be added to ordinary solder. REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
  • Page 3: Servicing Note

    D-EJ2000 SECTION 1 SERVICING NOTE BEFORE REPLACING THE OPTICAL PICK-UP BLOCK NOTES ON HANDLING THE OPTICAL PICK-UP Please be sure to check thoroughly the parameters as par the “Optical BLOCK OR BASE UNIT Pick-Up Block Checking Procedures” (Part No.: 9-960-027-11) issued separately before replacing the optical pick-up block.
  • Page 4 D-EJ2000 SERVICE MODE 2. Operation when the Service Mode is set. When the Service Mode becomes active, following messages are The following confirmation can be performed when the Service displayed onthe remote control LCD. Mode is set. Remote control LCD display 1.
  • Page 5 D-EJ2000 5) C1 error rate display mode is active by pressing [DISPLAY] button • x button (the CD player) or x button (the remote control) All servos (Focus/Tracking/Sled) off (the remote control). • > / . button (the CD player) or > / . Rotary The remote control LCD displays the following message.
  • Page 6: General

    D-EJ2000 SECTION 2 GENERAL This section is extracted from instruction manual. Locating the controls CD player (front) Remote control 1 EXT BATT (external battery)/ qd x (stop) button qg Display DC IN 3 V (external power input) jack 2 Jog lever (u (play/pause)•...
  • Page 7: Disassembly

    D-EJ2000 SECTION 3 DISASSEMBLY Note : Disassemble the unit in the order as shown below. UPPER LID SECTION CABINET (MIDDLE) SECTION MAIN BOARD, OPTICAL PICK-UP SECTION (CDM-3325ES2) MOTOR ASSY (TURN TABLE)(M902), OPTICAL PICK-UP ASSY (DAX-25E) Note : Follow the disassembly procedure in the numerical order given.
  • Page 8: Cabinet (Middle) Section

    D-EJ2000 3-2. Cabinet (Middle) Section 3 claw 1 six screws 2 screw 3 claw 3 two claws 4 cabinet (middle) assy 5 spring (upper lid) 3-3. MAIN Board, Optical Pick-Up Section (CDM-3325ES2) The cautions at the time of attachment 1 spacer...
  • Page 9: Motor Assy Turn Table (M902)

    D-EJ2000 3-4. Motor Assy (Turn Table)(M902), Optical Pick-Up Assy (DAX-25E) 2 motor assy 1 three screws ( B 1.7 × 4 ) (turn table)( M902 ) 3 three screws ( B 1.7 × 4 ) 4 gear cover 5 gear (B)
  • Page 10: Electrical Adjustment

    D-EJ2000 SECTION 4 ELECTRICAL ADJUSTMENT Adjustment of VCPU Connection : • DC 3 V in DC IN jack (J402) Digital Voltmeter MAIN board TP (VCPU) TP402 (GND) – Procedure : 1. Connect a digital voltmeter to the test points TP (VCPU) and TP402 (GND).
  • Page 11: Diagrams

    D-EJ2000 SECTION 5 DIAGRAMS The CD section adjustments are done automatically in this set. RF Level Check NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS In case of operation check, confirm that RF level. Condition: • Hold the set in horizontal state.
  • Page 12: Block Diagram - Main (1/2) Section

    D-EJ2000 5-1. Block Diagram – Main Section (1/2) – IC601 RF AMP, DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, D-RAM CONTROLLER DETECTOR WDCK DOUT DOUT DIGITAL WFCK IC602 D-RAM RFDC RFAC XTAO D0-D3 XTAI VCPU OPGSW RFAC OPTICAL PICK-UP BLOCK OPSTB...
  • Page 13: Block Diagram - Main (2/2) Section

    D-EJ2000 5-2. Block Diagram – Main Section (2/2) – VCC3 DOUT J301 OPTICAL TRANSMITTER LINE OUT (OPTICAL) AOUTR AOUTL (LINE OUT JACK) Q101, 201 MUTING J302 IC301 HEADPHONE AMP IN_L OUT_L AOUTL AOUTR IN_R OUT_R Q302 BEEPO_L LINE MUTE CONTROL SWITCH...
  • Page 14: Block Diagram - Power Supply Section

    D-EJ2000 5-3. Block Diagram – Power Supply Section – IC402 (3/3) POWER CONTROL PA PC LDOUT LDIN Q412 SWITCH VLGO4 INM4 CHARGING BATTERY BATM1 VOLTAGE DETECTOR RF41 CHGSW CIRCUIT CHGMNT VOUT D408 L412 LINEAR SYNC SYNC INP1 CONSTANT CURRENT, RECHARGEABLE...
  • Page 15: Printed Wiring Board - Main Board (Side A)

    D-EJ2000 Ver 1.1 2002.12 5-4. Printed Wiring Board – MAIN Board (Side A) – • : Uses unleaded solder. MAIN BOARD (SIDE A) S806 MAIN BOARD (Side A) • Semiconductor Location Ref. No. Location D401 D801 D402 (CHARGE) D403 D405...
  • Page 16: Printed Wiring Board - Main Board (Side B), Sub Board

    D-EJ2000 5-5. Printed Wiring Board – MAIN Board (Side B), SUB Board – • : Uses unleaded solder. MAIN BOARD (SIDE B) TP609 (RF) SUB BOARD SUB BOARD (SIDE B) (SIDE A) OPTICAL S801 PICK-UP HOLD BLOCK HOLD DAX-25E TP411...
  • Page 17: Schematic Diagram - Main Board (1/3)

    D-EJ2000 Ver 1.1 2002.12 5-6. Schematic Diagram – MAIN Board (1/3) – • See page 11 for Waveform. • See page 20 for IC Block Diagrams. Q302 XP4312 CN601 R301 R107 L402 TP427 L403 TP428 C619 R207 L404 TP429 0.01...
  • Page 18: Schematic Diagram - Main Board (2/3)

    D-EJ2000 Ver 1.1 2002.12 5-7. Schematic Diagram – MAIN Board (2/3) – L416 L415 R440 TP417 L414 R449 Q410 2SD2216J-QR C460 (TX).SO IC405 TC75S58FU C439 Q407 C446 1000p TPC6201(TE85R) 4700p R458 100k R467 1M 0.5% C440 C451 1000p 6.3V Q409...
  • Page 19: Schematic Diagram - Main Board (3/3)

    D-EJ2000 Ver 1.1 2002.12 5-8. Schematic Diagram – MAIN Board (3/3) – • See page 11 for Wavefoms. (Not used) ∗ R817 22k:EXCEPT AEP, EE, UK R816 68k:AEP, EE, UK R817 ∗ R810 0.5% 0.5% AEP, R818 100k 0.5% C813 0.01...
  • Page 20: Ic Block Diagram

    D-EJ2000 5-9. IC Block Diagram IC301 TA2152FN (EL) IC402 TB2136F C-AMP MUTE OUTADJ BIAS_I BIAS_O BEEP_I PW_SW MU_TC VCC1 IN_L RFIN C-AMP SW BEEP PW/MUTE SW BIAS BEEPO_L OUT_L EQ_L OUT_C PWGND EQ_R OUT_R BEEPO_R VCC2 IN_R...
  • Page 21: Ic Pin Function Description

    D-EJ2000 5-10. IC Pin Funvtion Description • IC801 T5AJ4-4GC6 (SYSTEM CONTROLLER) Pin No. Pin Name Description — Ground (digital) System clock input from CXD3039AR (IC601) XOUT Crystal oscillator output terminal Not used (open) TEST Test terminal for IC Not used (open) VCPU —...
  • Page 22 D-EJ2000 Pin No. Pin Name Description PGMSEL Not used (open) VDSEL VD control signal output XPOWLT Latch signal output to the power control (IC402) CHGGND ON Ground control signal output at charging the rechargeable battery (fixed at “H”) HG XSTB Hologram control signal output (“L”...
  • Page 23: Exploded Views

    D-EJ2000 Ver 1.1 2002.12 SECTION 6 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Accessories are given in the last of the electri- • Color Indication of Appearance Parts Example: may have some difference from the original cal parts list.
  • Page 24 D-EJ2000 Ver 1.1 2002.12 6-2. Cabinet (Lower) Section CDM-3325ES2 not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3382-726-1 CABINET (LOWER) ASSY (B)(BLACK) 3-245-319-01 WINDOW (LED) (EXCEPT KR) 3-245-323-01 SPRING (UPPER LID) X-3382-727-1 CABINET (LOWER) ASSY (S)(SILVER)
  • Page 25 D-EJ2000 6-3. Optical Pick-Up Section (CDM-3325ES2) M902 not supplied M901 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-318-203-61 SCREW (B1.7X4), TAPPING A-3052-734-A FEED ASSY, SCREW 0 102 X-3380-950-1 OPTICAL PICK-UP (DAX-25E) 3-221-268-01 GEAR (B) 3-221-473-01 COVER, GEAR...
  • Page 26: Electrical Parts List

    D-EJ2000 Ver 1.1 2002.12 SECTION 7 MAIN ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • SEMICONDUCTORS When indicating parts by reference number, In each case, u: µ, for example: parts list may be different from the parts speci- please include the board name.
  • Page 27 D-EJ2000 Ver 1.1 2002.12 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C602 1-104-847-11 TANTAL. CHIP 22uF 20.00% 4V D405 8-719-404-50 DIODE MA111-TX C603 1-131-862-91 TANTAL. CHIP 47uF C604 1-164-874-11 CERAMIC CHIP 100PF 5.00% 50V...
  • Page 28 D-EJ2000 Ver 1.1 2002.12 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks L414 1-428-912-21 INDUCTOR 10uH R406 1-218-977-11 RES-CHIP 100K 1/16W L415 1-400-145-21 INDUCTOR 47uH R407 1-218-981-11 RES-CHIP 220K 1/16W R408 1-218-977-11 RES-CHIP 100K 1/16W...
  • Page 29 D-EJ2000 Ver 1.1 2002.12 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R466 1-208-951-81 METAL CHIP 470K 0.5% 1/16W R818 1-208-935-81 RES-CHIP 100K 0.5% 1/16W (AEP,EE,UK) R467 1-208-959-81 METAL CHIP 0.5% 1/16W R819 1-218-961-11 RES-CHIP 4.7K...
  • Page 30 D-EJ2000 Ver 1.1 2002.12 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < CONNECTOR > 3-245-379-51 MANUAL, INSTRUCTION (SLOVAK) (EE) 3-245-379-61 MANUAL, INSTRUCTION (KOREAN) (JE,KR) * CN401 1-817-020-21 CONNECTOR,FFC/FPC (NON-ZIF) 7P 3-245-379-71 MANUAL, INSTRUCTION (ENGLISH) (US) <...
  • Page 31 D-EJ2000 MEMO...
  • Page 32 D-EJ2000 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2002.09...

Table of Contents