Related Manuals for Graphic Products DuraLabel PRO 300
Summary of Contents for Graphic Products DuraLabel PRO 300
- Page 1 DuraLabel PRO 300 ® QuickStart Guide Read Me Graphic Products, Inc. First! 1-800-788-5572 503-644-5572 Local: www.DuraLabel.com www.GraphicProducts.com info GraphicProducts.com E-mail:...
-
Page 2: Minimum System Requirements
“Next.” 8. Check through the list provided and click “Finish.” 9. Click “Restart.” The DuraLabel PRO 300 printer driver may now be installed. Begin with page 7, Step 2 Connect Printer of the QuickStart Guide. Minimum System Requirements Operating System: Windows 2000 SP... - Page 3 ® the DuraLabel PRO 300. If you need more help with setting up your printer, please refer to the DuraLabel PRO 300 Manual (included on the installation CD), visit www.Duralabel.com or give us a call. Graphic Products, Inc. 1-800-788-5572 Please contact us for all your labeling needs.
-
Page 4: Table Of Contents
CONTENTS Contents of Package ......... pg. 3 1. Load Printer ..........pg. 4 Load Ribbon ..........pg. 4 Load Vinyl Tape ..........pg. 6 2. Connect Printer ..........pg. 7 3. Install Using USB Cable........ pg. 7 4. Install Using Parallel Cable ......pg. 8 5. -
Page 5: Contents Of Package
(black spindles, one will have a paper core on it) ▪ Label Supply Spindle ▪ 2 Fixing Tabs (for each end of the Label Supply Spindle) If you are missing a part, please call your Graphic Products Representative - 3 -... -
Page 6: Load Printer
PRO 300 have been optimized for compatibility and print quality. Only authorized supplies from ® Graphic Products will print correctly in the DuraLabel PRO 300. For more information about supply loading, please view the supply loading video on the installation CD. - Page 7 2. Place Ribbon Supply onto the empty Ribbon Supply Spindle and insert the spindle into the Rear Hub. 3. Place the Ribbon Rewind Spindle, with the paper core, on the Front Hub. Note: Make sure the flanges on the end of the ribbon spindles are on the right side of the printer when viewing from the front.
-
Page 8: Load Vinyl Tape
Load Vinyl Tape **IMPORTANT** Always turn OFF the power first! 1. With the Ribbon Mechanism still in upright position, center the Label Stock on the Label Supply Roll Spindle using the Fixing Tabs. (See Figure 4) Fixing Tab Figure 4 Vinyl Tape Printing Side Face Up... -
Page 9: Connect Printer
**IMPORTANT** These Steps need to be done in the order below! 1. Connect the power supply. 2. Connect the DuraLabel PRO 300 to your PC using the USB or parallel cable. 3. Turn on the DuraLabel PRO 300. (Switch is in back of printer, See Figure 6) Figure 6 1. -
Page 10: Install Using Parallel Cable
12. If given a choice to keep or replace the existing driver, select “Replace existing driver” and click “Next.” 13. Leave the default name as “Graphic Products DuraLabel PRO 300,” select if you wish to use it as the default printer and click “Next.”... -
Page 11: Set Up To Print
Perform these changes before opening the document you wish to print. Continuous Label Stock The Default Printing Preferences on your DuraLabel PRO 300 should be at the proper settings for printing on continuous vinyl and should require no adjustments. To change settings: 1. - Page 12 P.O. Box 4030 www.DuraLabel.com 1-800-788-5572 Beaverton, OR 97076 © 2008, 2009, Graphic Products, Inc. All Rights Reserved v. 1.0 - 8/11/09...
Need help?
Do you have a question about the DuraLabel PRO 300 and is the answer not in the manual?
Questions and answers