Table of Contents
Advertisement
3. Editing
3. Editing
In Play mode and Individual mode, you can edit each
effect, set noise reduction and program level, and
modify the program name.
In Phrase Trainer mode, it is possible to edit the DRIVE-
AMP and CABINET effect blocks, but it is not possible to
perform editing operations that use the name display or
MASTER/VALUE display, or the cursor switches or the
MASTER/VALUE switches.
During editing, the edit icon in the display will blink.
Edit icon
Editing effects
Rotate the effect select knob of the effect block that you
wish to edit, or press the corresponding effect block
select switch. The effect block LED will begin blinking,
indicating that it has been selected for editing.
Use the effect select knob, effect block select switch,
and value knobs to edit the settings.
If you wish to save the edited effect, perform the
"Program write" operation. If you fail to do this, the effect
program will revert to its original settings when you turn
off the power or select a different program.
As an example, we will explain how to edit the TUBE
OD (Tube Overdrive) effect of the DRIVE-AMP block.
1. If the name display indicated "TUBE OD" when
you pressed the effect block select switch, simply
continue. If not, turn the DRIVE-AMP effect select
knob to the TUBE OD position. If the effect select
knob was already located at TUBE OD, first select a
different effect model, and then turn the knob back
to TUBE OD.
2. The effect block LED will begin blinking, indicating
that it has been selected for editing. (The name
display will indicate the model name as "TUBE
OD.") If you selected a programmed effect, the
ORIG icon will light.
3. The five value LED's will light, and the correspond-
ing value knobs will be assigned to DRIVE,
LEVEL, TREBLE, MIDDLE, and BASS respec-
tively, and will function as knobs that adjust the
value of each parameter. (Refer to p.16, "Effect
parameters.")
4. Rotate the knobs and the sound will change. The
name display will indicate the name of the
parameter assigned to that knob, and the MAS-
TER/VALUE display will indicate the value. At this
time, the ORIG icon will light when the position of
the knob matches the original value — i.e., the
value before you began editing.
12
The parameter assigned
to the knob you moved
Value of the parameter
Modifying a parameter value
TREBLE MIDDLE BASS
DRIVE LEVEL
Instead of the five value knobs, you can also use the
cursor switches to select parameters, and use the
MASTER/VALUE switches ( ,
of the parameter currently shown in the name display.
If you do not wish to use the DRIVE-AMP effect block,
press the DRIVE-AMP effect block select switch until
the LED goes dark. The DRIVE-AMP effect block is
now bypassed, and the name display will indicate "-
OFF-."
For some effects, it is not possible to simultaneously use
the MODULATION and PEDAL effect blocks, or the
PEDAL and AMBIENCE effect blocks. If you attempt to
turn on both effect blocks in such a combination, the
block that had been turned on will automatically be
turned off.
Quick Editing for the DRIVE-AMP
effect block
In the default state of each mode, the DRIVE-AMP
effect block parameters used by the selected program
are assigned to the value knobs (except when the effect
is off).
By rotating the respective value knobs, you will enter
Edit mode (the effect block LED will blink); the name
display will indicate the parameter name, the MAS-
TER/VALUE display will show the value, and the
sound will change.
If you wish to change an effect that is in use, use the
effect select knobs to select the desired effect.
It is not possible to edit when other functions are
assigned to the value knobs, when the AX1000G is
bypassed, muted, or recording in Phrase Trainer mode.
Selecting a parameter
) to adjust the value
Hide quick links:
Advertisement
Table of Contents
